Digital news editing workstation, editing control panel, extended input and keyer board, video effects board, 3d/lighting/trail effects board, operating program (72 pages)
Page 20
Table of contens WARNING WARNING: THIS WARNING IS APPLICABLE FOR USA ONLY. (for the DNE-1000) To prevent fire or shock hazard, do not expose the unit to If used in USA, use the UL LISTED power cord specified rain or moisture.
Page 21
Features ................... 2(E) Overview of Options ...............3(E) System Configuration ..............4(E) Location and Function of Parts ............5(E) DNE-1000 Digital News Editing Workstation ........ 5(E) BKNE-1010 Editing Control Panel ..........8(E) BKNE-1011 Editing Fader Panel ............ 9(E) Example Connections ................ 10(E) Example Configuration of Stand Alone System ......
Audio Inputs/outputs and processing Digital audio processing As an audio mixer, the DNE-1000 can handle 20 channels of digital audio input signals (with 20-bit processing on each channel). It is equipped with input and output routers, highpass filters, notch filters, mix down and master fader controls.
Connect the time code to be used as the basis for all of confirmation of two pictures) during editing. the editing operations to the REF TC IN connector on the DNE-1000. BKNE-1040 Video Effects Board Wide range of systems supported This board adds a variety of video effects.
Overview System Configuration The following figure shows an example system configuration based on the DNE-1000. Computer Video monitor A/V server network BKNE-1010 BKNE-1011 Editing Control Editing Fader Ethernet interface board Panel Panel Ethernet interface board Video overlay board CONTROL EDITOR...
If the indicator does not light even when the POWER switch is in the on position, there may be a fault in the power supply circuit. In this case, return the switch to the off position, and contact your Sony service representative. 5(E)
Page 26
100 to 240 V AC power supply. 7 REF IN (reference input) connectors (BNC) 3 Signal ground terminal To synchronize the DNE-1000 with an external device, If necessary, use this to ground the unit. input an analog reference video signal (black burst signal or sync signal).
Page 27
Rear panel (left part) 1 AUX INPUT 1 to 4 connectors 2 PGM OUT 1/2, 3/4 connectors 3 MONITOR L, R connectors 4 DEVICE CONTROL connectors 9 REF TC IN connector 8 PANEL connector 7 GPI connector 6 RS232C connector 5 GUI connectors 1 AUX (auxiliary) INPUT 1 to 4 connectors (XLR 5 GUI (graphical user interface) connectors (D-...
(XLR 3-pin, upper female, lower male) Connect to the BKNE-1010 control panel. When the DNE-1000 is used in a system connected to a server, connect the in-house reference time code signal to the upper connector. The lower connector provides a loop-through output of the same reference signal.
BKNE-1011 Editing Fader Panel For details of the use of the knobs and levers on the control panel, refer to the BZNE-2020 User’s Guide. 1 Function knobs 2 Faders 3 Function indicators 4 Audio indicators 5 Transition lever KNOB LEVER INPUT CONTROL PANEL Connector panel...
Audio A/D converter INPUT Microphone Headphones WORD SYNC OUTPUT 2 EDIT PVW OUTPUT MONITOR L,R PANEL DEVICE DNE-1000 Digital News CONTROL Editing Workstation Audio monitor system CAPTURE OUTPUT AC IN REF IN BKNE-1010 Editing Control Panel PGM OUTPUT 3 Overlay...
Audio A/D converter INPUT Microphone Headphones WORD SYNC OUTPUT 2 EDIT PVW OUTPUT MONITOR L,R PANEL DEVICE DNE-1000 Digital News CONTROL Editing Workstation Audio monitor system CAPTURE OUTPUT AC IN REF IN BKNE-1010 Editing Control Panel PGM OUTPUT 3 Overlay...
Design and specifications are subject to change BNC (× 2, loop-through), 75 Ω without notice. REF IN 0.3 to 2 Vp-p, analog black burst signal or composite sync, 525/ DNE-1000 Digital News Editing 625 common Workstation Audio input/output connectors General Digital input PRIMARY INPUT BNC (×...
Control connectors Accessories not supplied D-sub 15-pin, female 10BASE-5 AC power cord compliant • For customers in the USA and Canada PANEL D-sub 15-pin, female RS-422A DK-2401 (UC): Power cord (125 V, 10 A, 2.4 m compliant, including +12 V (8 feet)) power output and LED control Plug retainer...
General To guarantee operation: 5 to 40°C (41 to 104°F) Power requirements To guarantee performance: 10 to +12 V (supplied from DNE-1000 35°C (50 to 95°F) through BKNE-1010) Relative humidity To guarantee operation: at least Power consumption 4.2 W (including BKNE-1010...
BKNE-1030 Extended Input and BKNE-1031 Frame Memory Keyer Board Board General General Power requirements Power requirements +5 V±0.2 V +5 V±0.2 V –5 V±0.1 V Power consumption Power consumption 25 W 20 W Temperature Storage: –20 to +55°C Temperature Storage: –20 to +55°C (–4 to +131°F) (–...
Specifications BKNE-1041 3D/Lighting/Trail Effects Board Power requirements +5 V±0.2 V Power consumption 20 W Temperature Storage: –20 to +55°C (– 4 to +131°F) To guarantee operation: 5 to 40°C (41 to 104°F) To guarantee performance: 10 to 35°C (50 to 95°F) Relative humidity To guarantee operation: at least To guarantee performance: at least 307 ×...
Page 37
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any...