Related Manuals for Toshiba VTD1551
Summary of Contents for Toshiba VTD1551
- Page 1 MODEL VTD1551 USER GUIDE DIGITAL VIDEO Region discs only Combination 15” Flat TV and DVD Video Player TELETEXT 5Q40201A Cov-In 8/4/04, 1:57 PM...
- Page 2 WARNING To prevent fire or shock hazard, do not expose this equipment to rain or moisture. MAINS SUPPLY This unit is designed to operate from AC 230V~240V 50Hz household mains supply. This unit is supplied with an approved 13 amp (BS 1363) fused mains plug. When replacing the fuse always use a 5 amp (BS 1362) approved type.
-
Page 3: Precautions
PRECAUTIONS SOME DOS AND DON'TS ON THE SAFE USE OF EQUIPMENT This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. -
Page 4: Table Of Contents
FEATURES • Multi-Angle • Auto Set up (Channel) • Repeat Playback • Auto Channel Memory • Memory/Random Playback • TELETEXT Function • Zoom • On-Screen Programming • Video Aspect Ratio • Picture Control Adjustments • Parental Control • Auto Power Shut Off •... -
Page 5: Location Of Controls
LOCATION OF CONTROLS Front Disc tray Phones socket Remote sensor VIDEO/AUDIO IN (L/R) jacks (AV2) Main Power Switch OPEN/CLOSE button FWD SKIP button STANDBY Indicator REV (Reverse) SKIP button VOLUME buttons STOP button CHANNEL buttons PLAY button Rear Indoor Aerial Holder Mains Lead to AC outlet RF IN jack 21 pin SCART (AV1) -
Page 6: Remote Control
REMOTE CONTROL Page TV/DVD Select to operate TV or DVD 8,13,21 OPEN/CLOSE Open or Close the tray 22,24,25,38 ON/STANDBY Power on/off 9,13,21,22 Direct channel selection of TV 13,14 Input setting 25,28,30 Enter a security code 36,37 VOLUME ▲/▼ Volume Up/Down 13,14 MUTE Mute... - Page 7 REMOTE CONTROL BATTERY INSTALLATION Slide the battery compart- Install two “AAA/R03/UM-4” Replace the cover. ment cover in the direction (penlight size) batteries, of the arrow. paying attention to the polarity diagram in the battery compartment. BATTERY CAUTIONS • Use two “AAA/R03/UM-4” size batteries for the remote control transmitter. •...
-
Page 8: Aerial Connections
AERIAL CONNECTIONS Connect an indoor or outdoor aerial to the aerial socket at the rear panel as shown below. For all aerial circuit problems, please consult your local dealer. Aerial socket Mains lead INDOOR AERIAL A loop aerial is supplied with the unit. Insert the aerial holder into the mounting hole on the back cabinet until it locks into place. -
Page 9: Connection To Other Equipment
CONNECTION TO OTHER EQUIPMENT The exact arrangement you use to interconnect various video and audio components to the unit is dependent on the model and features of each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs. - Page 10 CONNECTION TO OTHER EQUIPMENT Input Selection If you connect the unit to a VCR, camcorder or games console, you can select this input by pressing the 0/AV button. AV1(Scart socket) Press the TV/DVD button to select TV mode and then press the 0/AV button repeatedly to select AV1 AV2(Front AV input) or AV2.
-
Page 11: Automatic Tuning System
AUTOMATIC TUNING SYSTEM Your television has an Automatic Tuning System which makes tuning in your television easy. This Automatic tuning System scans the entire reception range in your area and automatically stores all available channels of suitable signal strength in the correct order e.g. BBC1 will tune into channel 1, BBC2 will tune into channel 2, etc. ONLY WHEN YOU TURN ON THIS UNIT FOR THE FIRST TIME, THE AUTOMATIC TUNING PROCESS WILL BE AVAILABLE. -
Page 12: Presetting The Channels
PRESETTING THE CHANNELS Once you have connected up this unit, - Automatic tuning The stations will be preset in the order that you will need to tune in the channels in they appear when the automatic tuning is order to watch TV stations. There are two activated. - Page 13 PRESETTING THE CHANNELS MANUAL TUNING How to tune a station to channel 10 position. Press MENU. MENU Press to select the CHANNEL SETUP CHANNEL SETUP mode, then PICTURE press ENTER. AV COLOUR PAL PRESS: ▲ / ▼ / ENTER / MENU Press to select the MANUAL mode, then press...
- Page 14 PRESETTING THE CHANNELS TO CHANGE THE CHANNELS EXAMPLE: Changing of channel position from CH2 and CH5. Press MENU. MENU Press to select the CHANNEL SETUP CHANNEL SETUP mode, then PICTURE press ENTER. AV COLOUR PAL PRESS: ▲ / ▼ / ENTER / MENU Press to select the CH ALLOCATION mode, then press...
-
Page 15: Tv Operations
TV OPERATIONS After completing the connection and Press Power ( ) on the front panel of the unit. Then press presetting the channels, follow these ON/STANDBY on the remote control (STANDBY indication steps for viewing. will goes off). Press TV/DVD to select TV mode. Direct Channel Selection buttons (0-9) Press the Direct Channel Selection buttons on the remote control. -
Page 16: Convenient Functions
CONVENIENT FUNCTIONS The following functions are available TV/AV Selection from the remote control handset only. For receiving the desired signal: Press 0/AV to select the TV or AV mode. +0 # TV position - to view a AV position - to receive through the direct Video normal TV. -
Page 17: Picture Adjustments
PICTURE ADJUSTMENTS The picture settings have been Press MENU. adjusted at the factory under optimum signal reception conditions. However, you can adjust for BRIGHTNESS, Press to select the CONTRAST, COLOUR and SHARP- MENU PICTURE mode, then press NESS to your preference. ENTER. -
Page 18: Av Colour Adjusting
AV COLOUR ADJUSTING When connecting external equipment Press MENU on your remote to the unit, the picture may become MENU control. The on screen display black and white. This can be corrected will appear. CHANNEL SETUP by selecting AV (Extension) Colour as Press ▲... -
Page 19: Reception Of Interference
RECEPTION OF INTERFERENCE The most common types of television interference are as follows. IGNITION Black spots and horizontal streaks may appear, the picture may flutter or drift. This is usually caused by interference from car ignition system, neon lamps, electric drills or other electrical appliances. -
Page 20: Teletext
TELETEXT Most broadcasters offer a Teletext service in addition to their standard TV program. Teletext offers news, weather forecast, winning Lotto numbers, TV listings and other interesting news. The text is received page by page, as soon as you select the broadcasting station. A single page can be displayed on the screen. - Page 21 TELETEXT To call a teletext page Leaf through the pages with the PAGE ( ) - button (forward or Enter the three-digit page number with the backward). number buttons. NOTE: You will not necessarily find a page for every page number you Example: enter.
-
Page 22: Disc
DISC The region number of this unit is 2. If region numbers, which stand for their playable area, are printed on your DVD video disc and you do not find , disc playback will not be allowed by the player. (In this case, the unit will display a message on-screen.) Playable Discs The loaded Disc (DVD, Video-CD, Audio-CD, SVCD and MP3/WMA/JPEG-CD) will be recognized automatically. -
Page 23: Preparation
PREPARATION/STATUS DISPLAY OF DISC The following pages describe the Preparation setup/operation in DVD mode. Before DVD/CD operation, please make preparations as follows. Insert the AC cord plug into a standard 230V~240V 50Hz AC outlet. • If the AC cord plug is plugged in for the first time, wait for about 5 seconds before pressing Power ( ) button on the front. -
Page 24: Playback Procedure
PLAYBACK PROCEDURE Press (OPEN/CLOSE) on the unit or OPEN/ CLOSE on the remote control. The disc tray will open. Place a disc onto the tray. Position it with the printed label side up, align it with the guides, and place it in its proper position. -
Page 25: Special Playback
SPECIAL PLAYBACK Note: There may be a slight delay be- Fast Forward Playback tween when you press the button and Press SEARCH during normal playback. the function activating. Each press of the SEARCH button will increase the speed of the search (x 2), (x 4), (x 8),... -
Page 26: Mp3/Wma/Jpeg Playback
MP3/WMA/JPEG PLAYBACK This player can play back the MP3/WMA/JPEG- MP3/WMA/CD playback data which has been recorded on CD-R or CD- RW. To produce the MP3/WMA/JPEG-data, you Press (OPEN/CLOSE). need a Windows-PC with CD-R/RW drive and a The disc tray will open. MP3/WMA/JPEG-encoding Software (not sup- Place a disc on which MP3 or WMA plied). - Page 27 MP3/WMA/JPEG PLAYBACK JPEG CD playback Press (OPEN/CLOSE). The disc tray will open. Place a disc on which JPEG files have been recorded onto the tray. Press (OPEN/CLOSE) or 1 Reading (PLAY). The disc tray closes au- tomatically. On the TV-screen, “Reading”...
-
Page 28: Setting The Jpeg Interval
SETTING THE JPEG INTERVAL Setting the JPEG Interval You can continuously play back all JPEG files automatically. Press SETUP in the stop Language Picture Sound Parental mode. Press to select “Pic- ture”, then press ENTER. /Enter/Setup/Return Press to select Language Picture Sound Parental... -
Page 29: Setting The Select Files
SETTING THE SELECT FILES When playing back a CD containing a mix- Press SETUP in the stop mode. Language Picture Sound Parental ture of MP3 and JPEG files, only MP3 or Press to select “Picture”, JPEG files can be displayed on the file menu. then press ENTER. -
Page 30: Zooming
ZOOMING/LOCATING DESIRED SCENE Zooming This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame. Press ZOOM during play- back. The centre part of the image will be zoomed in. Each press of ZOOM will change the ZOOM (Min.),... -
Page 31: Repeat Playback
REPEAT PLAYBACK Title, Chapter, Track Playback Press PLAY MODE during playback or stop mode. VCD/CD Repeat Play Mode /Enter/Play Mode Repeat /Enter/Play Mode /Enter/Play Mode Press ENTER once or twice to select “Chapter” or “Title”. In case of CD, at first press to select “Repeat”... -
Page 32: Program Playback/Random Playback (Vcd/Cd)
PROGRAM PLAYBACK/RANDOM PLAYBACK (VCD/CD) Program playback You can arrange the order of tracks on the disc. Press PLAY MODE in the stop mode. Play Mode Repeat /Enter/Play Mode Press ENTER repeatedly until Play Mode Program the program table shown at right Repeat appears. -
Page 33: Marking Desired Scenes
MARKING DESIRED SCENES The unit stores the points that you Marking the Scenes want to watch again. You can resume Press MARKER during playback from that scene. Marker playback. Marker Marker /Enter/Cancel/Marker Select the blank Marker Marker using , then press Marker ENTER at the desired Marker... -
Page 34: Changing Soundtrack Language/Subtitles
CHANGING SOUNDTRACK LANGUAGE/SUBTITLES Changing soundtrack language You can select the language when you play a multilingual disc. Press AUDIO during play- back. 1/8 Eng Dolby Digital The current soundtrack language will appear. Press AUDIO repeatedly until the desired language 2/8 Fra Dolby Digital is selected. -
Page 35: Changing Angles
CHANGING ANGLES/TITLE SELECTION/DVD MENU Changing Angles When playing back a disc recorded with multi-angle facil- ity, you can change the view angle. Press ANGLE during play- back. The current angle will ap- pear. Press ANGLE repeatedly until the desired angle is selected. Title Selection Two or more titles are recorded on some discs. -
Page 36: Setting The Aspect Ratio Of Tv Screen
SETTING THE ASPECT RATIO OF TV SCREEN/SETTING ON SCREEN DISPLAY Setting the aspect ratio of TV screen You can select the aspect ratio of the picture. Press SETUP in the stop mode. Language Picture Sound Parental Press to select “Picture”. /Enter/Setup/Return Press or ENTER, then press... -
Page 37: Dynamic Range Control
DYNAMIC RANGE CONTROL DRC (Dynamic Range Control) ena- Press SETUP in the stop Language Picture Sound Parental bles you to control the dynamic range mode or No Disc. so as to achieve a suitable sound for Press to select your equipment. “Sound”. -
Page 38: Parental Control Setting
PARENTAL CONTROL SETTING Some discs are specified not suitable Language Picture Sound Parental Press SETUP in the stop mode for children. Such discs can be limited or No Disc. not to play back with the unit. Password Press to select “Pa- Parental rental”. -
Page 39: To Change The Parental Level
TO CHANGE THE PARENTAL LEVEL Language Picture Sound Parental Press SETUP in the stop mode or No Disc. Password Press to select Parental “Parental”. Then press 0 9/Cancel ENTER. /Enter/Setup/Return Language Picture Sound Parental Press Number buttons (0-9) to enter the password you Password 1234 have stored. -
Page 40: Temporary Disabling Of Rating Level By Dvd Disc
TEMPORARY DISABLING OF RATING LEVEL BY DVD DISC Depending on the DVD disc, the disc Load a DVD disc and press PLAY may try to temporarily cancel the or OPEN/CLOSE (see page 22). rating level that you have set. It is up to you to decide whether to cancel the rating level or not. -
Page 41: Setting Menu Language
SETTING MENU LANGUAGE You can select the language of the Press SETUP in the stop mode. disc menu messages of DVDs. Language Picture Sound Parental Press to select “Lan- guage”. /Enter/Setup/Return Press or ENTER. Language Picture Sound Parental Then press to select Menu English... -
Page 42: Setting Subtitle Language
SETTING SUBTITLE LANGUAGE The same subtitle language can Press SETUP in the stop mode. Language Picture Sound Parental always be selected even if you replace Press to select “Lan- the disc or turn the power off. guage” /Enter/Setup/Return Press or ENTER. Language Picture Sound... -
Page 43: Setting Audio Soundtrack Language
SETTING AUDIO SOUNDTRACK LANGUAGE The same audio soundtrack language Press SETUP in the stop mode. Language Picture Sound Parental can always be selected by your unit Press to select “Language”. even if you replace the disc or turn the power off. /Enter/Setup/Return Press or ENTER. -
Page 44: Language Code List
LANGUAGE CODE LIST Enter the appropriate code number for the initial settings "AUDIO", "SUBTITLE" and/or "MENU LANGUAGE" (see pages 39~41). Language Name Code Language Name Code Language Name Code Language Name Code Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919 Afar 1111 Finnish 1619 Lithuanian... -
Page 45: Before Requesting Service
BEFORE REQUESTING SERVICE If your unit does not work properly check the following before calling a service engineer. SYMPTOMS CAUSE SOLUTION PAGE POWER The Mains lead is not connected. Connect Mains lead to AC outlet. No power. ON/STANDBY button is OFF. Set it to ON. -
Page 46: Specifications
Exemptions ■ Toshiba is not liable for any damage caused by fires, natural disaster (such as thunder, earthquake, etc.), acts by third parties, accidents, owner’s misuse, or uses in other improper conditions. - Page 47 5Q40201A P38-LAST 8/4/04, 1:59 PM...
- Page 48 04/08 U 5Q40201A P38-LAST 8/4/04, 1:59 PM...