Page 1
Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http:// ZZZYLHZVRQLFFRP LQ (QJOLVK RU LQ VSHFL¿F ODQJXDJHV XVLQJ WKH 5HJLRQDO VHOHFWLRQ box in the upper right corner of our website.
Page 2
Thank you for choosing ViewSonic As a world leading provider of visual solutions, ViewSonic is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity. At ViewSonic, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic product you have chosen will serve you well.
Page 3
Compliance Information FCC Compliance Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 4
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Proposed Maximum Substance...
Page 5
Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this unit near water. Clean with a soft, dry cloth. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions.
Page 6
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation. Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
Page 7
Product Registration To fulfill possible future product needs, and to receive additional product information as it becomes available, please visit your region section on ViewSonic’s website to register your product online. The ViewSonic CD also provides an opportunity for you to print the product registration form.
Table of contents Important safety Using the CEC function..... 34 Using the 3D functions ...... 34 instructions .......2 Using the projector in standby mode. 35 Introduction......4 Adjusting the sound ......35 Shutting down the projector ....36 Projector features ......... 4 Menu operation........
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions Please read this manual before you operate your projector.
Page 10
Do not block the ventilation holes. If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire. - Do not place this projector on a blanket, bedding or any other soft surface. - Do not cover this projector with a cloth or any other item. - Do not place inflammables near the projector.
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features. • Dynamic mode adjusting the power consumption of the lamp according to the brightness of the image being projected •...
The supplied accessories will be suitable for your region, and may differ from those illustrated. Projector Power Cord VGA Cable Multi-language User Quick Start Guide Remote Control & Batteries Manual CD Optional accessories Replacement lamp (RLC-092 for PJD5353LS. RLC-093 for PJD5553LWS.) Soft carry case VGA-Component adapter Dust filter Cable management cover...
Projector exterior view External control panel Front/upper side (See "Projector" on page 7 details.) Lamp cover Vent (heated air exhaust) Front IR remote sensor Adjuster foot Focus ring Projection lens Lens cap Audio signal output socket Audio signal input socket Video input socket S-Video input socket HDMI port...
Controls and functions Projector Focus ring (My Button) Adjusts the focus of the projected image. Allows user to define a short cut key on Menu this button, and the function item is selected in OSD menu. Turns on the On-Screen Display (OSD) menu.
Page 15
Remote control COMP1 COMP2 HDMI Auto Source Sync Enter Menu Exit PgUp PgDn Mouse Pattern Blank Color Mode Mode Enter To use the remote mouse control keys (Page Up, Page Down, , and ), see Enacts the selected On-Screen Display "Using the remote mouse control"...
Page 16
Mouse Exit Switches between the normal and mouse Goes back to previous OSD menu, exits modes. and saves menu settings. PgUp (Page Up)/PgDn (Page Down) PgUp, PgDn, : active after pressing Operates your display software program Mouse. An icon appears on the screen to (on a connected PC) which responds to indicate the activation of the mouse mode.
Page 17
Using the remote mouse control The capability of operating your computer with the remote control gives you more flexibility when delivering presentations. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer’s mouse. See "Connecting a computer"...
Page 18
Replacing the remote control batteries To open the battery cover, turn the remote control over to view its back, press on the finger grip on the cover and pull it up in the direction of the arrow as illustrated. Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment.
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.
Projection dimensions The "screen" mentioned below refers to the projection screen usually consisting of a screen surface and a support structure. PJD5353LS • 4:3 image on a 4:3 screen • 16:9 image on a 4:3 screen (e): Screen (f): Center of lens...
Page 21
PJD5553LWS • 16:10 image on a 16:10 screen • 16:10 image on a 4:3 screen (e): Screen (f): Center of lens 16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen (a) Screen (c) Image (d) Vertical (c) Image (d) Vertical Size Projection...
Connection When connecting a signal source to the projector, be sure to: Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents"...
Connecting a computer or monitor Connecting a computer Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER IN 2 signal input socket on the projector.
Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: • HDMI • Component Video • S-Video • Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality.
Page 25
Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly. VGA-Component adapter (ViewSonic P/N: CB-00008906) Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: •...
If you have already made a Component Video connection between the projector and this S- Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality.
Operation Starting up the projector Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). (If available) Remove the lens cap. Press Power to start the projector. As soon as the lamp lights up, a "Power On Ring Tone"...
H. Size Language English Zoom Projector Position Front Table Menu Settings Blank Timer Disable Splash Screen ViewSonic Analog RGB MENU Exit My Button Auto Advanced Analog RGB MENU Exit Press Exit twice* to leave and to highlight the SYSTEM save the settings.
Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus"...
Page 30
Press and hold Auto Sync on the remote control RECALL PASSWORD for 3 seconds. The projector will display a coded Please write down the recall code, number on the screen. and contact ViewSonic Customer Center. Write down the number and turn off your Recall code: projector.
Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.
• Normal: Sets the HDMI color range as 15 - 235. • Auto: Sets the projector to detect the HDMI range of the input signal automatically. This function is only available when the HDMI input port is in use. Refer to the documentation of the device for information on the color space and HDMI range settings.
Fine-tuning the image clarity If necessary, sharpen the image by rotating the focus ring. Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps.
Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.
16:10 aspect ratio. 4:3 picture Panorama (PJD5353LS): Scales a 4:3 image vertically and horizontally in a non-linear manner so that it fills the screen.. 4:3 picture 2.35:1: Scales an image so that it is displayed in...
Page 36
Standard mode: Is designed for presentations under daylight environment to match PC and notebook coloring. ViewMatch mode: Switches between high brightness performance and accurate color performance. Movie mode: Is appropriate for playing colorful movies, video clips from digital cameras or DVs through the PC input for best viewing in a blackened (little light) environment.
Page 37
Adjusting Brilliant Color Go to the PICTURE > Advanced > Brilliant Color menu and press This feature utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in the projected picture. It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors.
Color Management Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it. If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc., you can project any image from the disc on the screen and enter the Color Management menu to make adjustments.
Page 39
Highlight Timer Period and decide the time period by pressing . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5- minute increments. If the timer is already on, the timer will restart whenever the Timer Period is reset. Press to highlight Timer Display and choose if you want the timer to show up on the screen by pressing...
Hiding the image In order to draw the audience's full attention to the presenter, you can press Blank to hide the screen image. Press any key on the projector or remote control to restore the image. The word 'BLANK' appears at the lower right corner of the screen while the image is hidden. SYSTEM SETTING: BASIC >...
Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance. If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over-heating.
Using the projector in standby mode Some of the projector functions are available in standby mode (plugged in but not turned on). To use these functions, be sure you have turned on the corresponding menus under SOURCE > Standby Settings, and the cable connections are correctly made. For the connection methods, see the Connection chapter.
Shutting down the projector Press Power and a confirmation message is displayed prompting you. If you don't respond in a few seconds, the message will disappear. Press Power a second time. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time.
Main menu Sub-menu Options Off/Blackboard/Greenboard/ Screen Color Whiteboard Auto/4:3/16:9/16:10 (PJD5553LWS)/Wide Aspect Ratio (PJD5553LWS)/Panorama (PJD5353LS)/2.35:1/ Anamorphic DISPLAY Keystone Position Phase H. Size Zoom Color Mode Brightest/Dynamic/Standard/ViewMatch/Movie Brightness Contrast...
Page 45
25 sec/30 sec Menu Settings Center/Top-Left/Top-Right/ Menu Position Bottom-Left/Bottom-Right Disable/5 min/10 min/15 min/ Blank Timer 20 min/25 min/30 min Splash Screen Black/Blue/ViewSonic/Off Auto/Projection (Projector Position)/Menu SYSTEM Position/Color Temp./Brightness/Contrast/3D SETTING: My Button Settings/Screen Color/Splash Screen/Message/ BASIC Quick Auto Search/CEC/Lamp Mode/DCR/Closed Caption/Power Saving/Freeze/INFORMATION...
Page 46
Main menu Sub-menu Options High Altitude Mode On/Off On/Off Mute On/Off Audio Volume Audio Settings Power On/Off Ring On/Off Tone Closed Caption Off/CC1/CC2/CC3/CC4 Normal/Economic/ Lamp Mode Dynamic/Sleep Mode Lamp Settings SYSTEM Reset Lamp Hours SETTING: Lamp Hours ADVANCED Filter Mode On/Off Filter Settings Reset Filter Hours...
Page 47
Description of each menu Function Description "Using Screen Color" on page 29 for details. Screen Color This function is only available when a PC input signal is selected. Aspect Ratio "Selecting the aspect ratio" on page 27 for details. Keystone "Correcting keystone"...
Page 48
Function Description Color "Adjusting Color" on page 29 for details. Tint "Adjusting Tint" on page 29 for details. This function is only available when a Composite video or S-Video input signal with NTSC system is selected. Sharpness "Adjusting Sharpness" on page 29 for details.
Page 49
Function Description Power Saving "Setting Power Saving" on page 48 for details. Auto Power Off Sleep Timer "Setting Sleep Timer" on page 48 for details. Selecting Enable enables you to restart the projector immediately within 120 seconds after turning it off. After 120 seconds, if the projector is not turned on again, it will directly enter the standby mode.
Page 50
Function Description Allows you to select which screen will be displayed during Splash Screen projector start-up. My Button Sets a hotkey on remote control. Pattern The projector can display several test patterns. It helps you adjust the image size and focus and check that the projected image is free from distortion.
Page 51
Function Description Selects a preferred closed captioning mode when the selected input signal carries closed captions. • Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings). Closed Caption This function is only available when a Composite video or S-Video input signal with NTSC system is selected.
Page 52
Function Description Source Shows the current signal source. Color Mode Shows the selected mode in the PICTURE menu. Resolution Shows the native resolution of the input signal. Current System Color System Status Shows input system format. Lamp Hours Displays the number of hours the lamp has been used. Filter Hours Displays the number of hours the filter has been used.
Maintenance Care of the projector You need to keep the lens and/or filter (optional accessory) clean on a regular basis. Never remove any parts of the projector. Contact your dealer when any part of the projector needs replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface.
Using the dust filter (optional accessory) CAUTION • It is important to clean the dust filter every 100 hours after the dust filter is installed. • Be sure to turn off the projector and unplug it from power source before installing or detaching the filter.
Highlight Reset and press Enter. The lamp time will be reset to '0'. CAUTION Remember to set Filter Mode to Off in the SYSTEM SETTING: ADVANCED > Filter Settings menu when using the projector with the dust filter removed. Setting Filter Mode to Off does not reset the filter timer.
Page 56
Open the OSD menu and go to the SOURCE > Auto Power Off menu. Press Enter and the Auto Power Off page is displayed. Highlight Sleep Timer and press If the preset time lengths are not suitable for your presentation, select Disable. The projector will not automatically shut down in a certain time period.
Page 57
Replacing the lamp Turn the power off and disconnect the projector from the power outlet. Please contact qualified service personnel for changing the lamp. Type number for the replacement lamp: • PJD5353LS: RLC-092 • PJD5553LWS: RLC-093...
Page 58
Indicators Light Status & Description Power events Blue Stand-by mode Flashing Powering up Blue Normal operation Blue Blue Normal power-down cooling (3 sec) Flashing Downloading Lamp events Blue First Lamp-Lit error cooling (60 sec) Flashing Lamp error in normal operation (30 sec) CW start fail (30 sec) Blue Lamp life exceeded...
Troubleshooting The projector does not turn on. Cause Remedy Plug the power cord into the AC inlet on the projector, and plug the power cord into the power There is no power from the power cord. outlet. If the power outlet has a switch, make sure that it is switched on.
All specifications are subject to change without notice. • Not all models can be purchased in your region. General Product name DLP Projector Optical Resolution PJD5353LS: 1024 x 768 XGA PJD5553LWS: 1280 x 800 WXGA Display system 1-CHIP DMD Lamp 190 W lamp...
Output terminal RGB output D-Sub 15-pin (female) x 1 Audio signal output Audio jack x 1 Speaker 2 watt x 1 Control terminal RS-232 serial control 9 pin x 1 USB serial control Type mini B IR receiver x 1 (Front) Environmental Requirements Operating temperature 0°C–40°C at sea level...
Timing chart Analog RGB Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) 640 x 480 60/72/75/85 SVGA 800 x 600 60/72/75/85 1024 x 768 60/70/75/85 1152 x 864 1280 x 768 15:9 WXGA 1280 x 800 16:10 60/75/85 1360 x 768 16:9 Quad-VGA 1280 x 960...
Page 63
HDMI Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) 640 x 480 SVGA 800 x 600 1024 x 768 1280 x 768 15:9 WXGA 1280 x 800 16:10 1360 x 768 16:9 Quad-VGA 1280 x 960 SXGA 1280 x 1024 SXGA+ 1400 x 1050 WXGA+...
Page 64
3D (HDMI signal included) Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SVGA 800 x 600 60* / 120** 1024 x 768 60* / 120** 1280 x 720 16:9 60* / 120** WXGA 1280 x 800 16:9 60* / 120** for Video Signal Signal Resolution (dots)
Page 65
Component video Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) HDTV (1080p) 1920 x 1080 16:9 50 / 60 HDTV (1080i) 1920 x 1080 16:9 50 / 60 HDTV (720p) 1280 x 720 16:9 50 / 60 SDTV (480p) 720 x 480 4:3 / 16:9 SDTV (576p) 720 x 576...
Copyright 2015. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation. Disclaimer...
Appendix IR control table Format Byte1 Byte2 Byte3 Byte4 PgDn PgUp Blank Auto sync Down Left Right Color Mode Enter Power ON Magnify Presentation Timer Exit D. ECO (Eco mode) Menu Mouse Mouse Left Mouse Right Source Pattern My button HDMI Volume+ Volume-...
Page 72
color temperature 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66 Warm color temperature 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67 Normal Write color Color temperature 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68 temperature Neutral color...
Page 79
Latin America C= http://www.viewsonic.com/ www.viewsonic.com/la/ soporte@viewsonic.com (Mexico) la/soporte/servicio-tecnico Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F. Tel: 55) 6547-6454 55)6547-6484 Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico Latin America C= http://www.viewsonic.com/ www.viewsonic.com/la/ soporte@viewsonic.com (Peru) la/soporte/servicio-tecnico Macau www.hk.viewsonic.com T= 853-2840-3687 service@hk.viewsonic.com...
Page 80
If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
Page 81
Exclusion of damages: ViewSonic's liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: Damage to other property caused by any defects in the product, damages based upon...
Page 82
Exclusion of damages: ViewSonic's liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.
Page 83
Tel: (52) 999-925-1916 Tel: 01(52)95-15-15-22-22 E-Mail: rrrb@sureste.com Fax: 01(52)95-15-13-67-00 E-Mail. gpotai2001@hotmail.com Tijuana: FOR USA SUPPORT: ViewSonic Corporation Av Ferrocarril Sonora #3780 L-C 14035 Pipeline Ave. Chino, CA 91710, USA Col 20 de Noviembre Tel: 800-688-6688 (English); 866-323-8056 (Spanish); Tijuana, Mexico E-Mail: http://www.viewsonic.com...