Casio CP-2070 Owner's Manual

INITIAL SETUP
B
WALL/DESK USE
A wall mount bracket is included and can be installed if needed. Tightly
coil the telephone cord around the four guides on the inside of the wall
mounting bracket. Pull the telephone cord through the center opening on
the wall mounting bracket. Refer to the drawing. The handset can be
charged face out or face down, even when wall mounted.
TONE/PULSE SWITCH
This switch tells the CP-2070 to dial out with either touchtone or pulse signals to match the service you
TONE/PULSE SWITCH
have with your local telephone company. The CP-2070 is shipped with the
in the TONE position. If you do not have touchtone service, set the switch to pulse on the back of the
charging cradle.
TONE = for Touchtone systems
PULSE = for Rotary dialing or Pulse systems
PULSE TONE
RINGER ON/OFF
The CP-2070 is shipped with the handset RINGER ON/OFF SWITCH in the ON position and the base
RINGER OFF/LOW/HIGH SWITCH in the HIGH position. You can independently set the ringers of the
CP-2070.
HANDSET / TELEPHONE OPERATION
HANDSET VOLUME CONTROL
STANDBY MODE
Whenever the CP-2070 is in "Talk" mode, the
1
The CP-2070 is in "Standby" mode
handset volume will be displayed.
whenever it is idle, waiting for a call. If the
1
handset is in the charging cradle, the Press the DOWN or UP ARROW KEY
display will either be blank
to adjust the volume during a call. The
volume will remain at that level for your
OR
next call.
1 If you have new caller ID entries from
recent unanswered calls, it will show the
CALL TIMER
"NEW CALLERS" message with the
number of new callers at the lower far About 10 seconds after you enter "Talk" mode, a
right of the display screen. Press Call Timer will appear on the display. The timer
CALLER ID to view the names and will automatically be reset whenever you place a
numbers of "New Callers". new call.
NOTES:
NOTE:
The length of time shown on the display is intended
If the handset is in "Standby Mode" but not in the
only to be an estimate duration of a phone call.
charging cradle, the display will go blank after a short
CASIO makes no guarantees regarding the accuracy
time to conserve battery power.
of this timer.
TO PLACE A CALL The Call Timer will not be disrupted if HOLD is
pressed. The Hold timer (5 minute count down timer)
will display and the Call Timer will continue, hidden
1 TALK
Pick up the handset and press . The
from view, during any Hold mode.
following display will be briefly shown. This
display indicates that the handset is estab- LAST CALL TIME DISPLAY
lishing contact with the charging cradle.
1 RIGHT ARROW (CHANNEL)
Press the
KEY
to view the approximate length of the
last call after you have hung up the phone.
2 A dial tone will be established. (In this
example, CH03 is the current channel
CHANGING CHANNELS
number of 60 available channels in your
MANUALLY
area.) Wait for dial tone and dial the phone
number. The number will appear in the
1 After TALK is pressed, the CP-2070 selects
display as you dial.
the best of 60 available channels in your
area. If you hear noise or interference while
CHANNEL
using the CP-2070, press on
NOTE:
the handset to change channels.
The HANDSET LINE IN-USE INDICATOR on the
charging cradle lights solid to show the handset is in
use.
FLASH/CALL WAITING
1
TO END A CALL If you subscribe to a call waiting service
and you receive another call while using the
phone, press FLASH to answer the
1 TALK
To hang up, press or return the
second call. To return to the first call, press
handset to the charging cradle.
FLASH
again.
NOTE:
When you return the handset to the charging cradle, FLASH may also be used on a business phone
you are hanging up the phone and returning to system (CENTREX, PBX) for transferring calls.
Standby Mode. The CP-2070 is now ready to receive
a call and the CHARGING INDICATOR lights solid to HOLD
show that the battery is charging.
You may place a call on hold while using the
cordless handset.
IF YOU MISDIALED
1 HOLD
Press to place a call on hold. The
A NUMBER
LINE IN-USE INDICATOR will flash slowly.
NOTE:
1 TALK
Press twice ("off" and "on.") Wait You can place a call on hold for up to 5 minutes.
During HOLD , do not return the handset to the
for dial tone and dial the correct number.
charging cradle. Doing so will disconnect the caller.
TO RECEIVE A CALL 2 To continue your phone conversation,
TALK HOLD
press , , or pick up an
1 When the phone rings, pick up the cordless extension phone connected to the same
TALK
handset and press . You will briefly line. When the extension phone is picked
up, the CP-2070 automatically disconnects
see the "SCANNING CHANNELS" display,
itself from the line. Extension phone pick-
followed by the "VOLUME" display. Speak
up during HS Hold mode will discontinue
to the caller.
the Hold mode, connect the call to the new
2 To hang up, press TALK on the handset or
extension phone, and cause the CP-2070 to
return the handset to the charging cradle.
go idle after a 10 -second display time out.
NOTE:
The Call Timer will not be disrupted if HOLD is
pressed. The Hold timer (5 minute count down timer)
will display and the Call Timer will continue, hidden
from view, during any Hold mode.
CALL WAITING & CALLER ID
NOTE:
CALLER ID SERVICE OPTIONS
The display illustrations in the remainder of this
section are presented with the assumption that your
You must subscribe to a Caller ID service
Caller ID service provides both name and number. If
(available from most local telephone companies)
you have a number-only service, the name will be
in order to receive Caller ID information. Most blank.
Caller ID services offer the following two options:
ANSWERING
1.Standard Caller ID with name and number
CALLER ID CALLS
The name, phone number and local time (if
available) of the incoming call are received
When you receive a call, the CP-2070 will receive
after your phone rings.
the Caller ID information from your phone
2.Call Waiting Caller ID with name and number company within the first two rings. Caller ID
The name, phone number and local time (if information will display even if the ringer is set to
available) of the incoming call are received off.
after your phone rings. If you are on the phone
When all of the data is received, you will hear a
and receive another call, you will hear a tone,
low-high confirmation tone and the Caller ID
telling you there is a call waiting. The Call
information will appear on the display:
Waiting Caller ID information will appear on the
display.
C
DIALING A NUMBER USING BATTERY CONDITION
THE SEND KEY You can check the power level of the battery to
avoid battery depletion.
(DISPLAY & DIAL)
1 BATTERY
Press when the handset is out
Send-Key Dialing is extremely reliable because
of the charging cradle. The following
you can see the number you have entered before
display will appear when the battery is fully
actually dialing it. charged:
1 Make sure the CP-2070 is in "Standby
Mode". Without pressing the TALK button,
enter the number you wish to dial. If you
DELETE
make a mistake, use to make As the battery discharges, the stack symbols will
changes. The last digit entered will be disappear, starting from the right. When the
DELETE
deleted. Each time is pressed, the battery is low, the display will look like:
previously entered digit will be erased.
2
After you have correctly entered the entire
SEND
number you wish to dial, press . The
2
BATTERY
CP-2070 will dial the number. Press again or wait a few
seconds to leave battery condition mode.
NOTES:
REDIAL
Charge the battery for 12-15 hours before using.
If BATTERY is pressed while the handset is in the
The CP-2070 remembers the last number you
cradle, "CHARGING" will appear in the LCD.
dialed. The redial memory will hold up to 32
digits. Every time you dial a new telephone
number, the redial memory is updated with that
LOW BATTERY INDICATOR
new number.
1 The CP-2070 will automatically detect a low
Press TALK and wait for a dial tone.
battery. If this happens, you will hear a double
beep, and the "LOW BATTERY" display will
2
REDIAL appear.
Press .
If the Low Battery indicator appears while you are
talking on the CP-2070, you may only have a few
minutes left before the battery discharges
REDIAL WHEN BUSY
completely, in which case you will be
If you receive a busy signal after placing a call disconnected. To prevent this, simply pick up an
and you wish to try again immediately, there is no extension phone and place the CP-2070 back in
need to hang up the phone. the charger. Place the handset in the charger for
12 - 15 hours to recharge the battery.
1 REDIAL
Press while hearing a busy signal
NOTE:
and the CP-2070 will automatically hang
The battery can be recharged many times, but if you
up, reconnect, and dial the number again.
get a low battery indication even after 12-15 hours of
charging, you should replace the battery pack. See
the Accessories order form to purchase a battery
DISPLAY REDIALING
pack.
Display Redialing allows you to view the contents
of the redial memory before dialing. This is
useful if you aren't sure what number was last OUT OF RANGE ALARM
dialed on the CP-2070.
The CP-2070 cordless handset operates like any
1
Make sure the unit is in "Standby" mode.
other cordless handset. You can use it in the
REDIAL
Press . You will be able to view
yard, at the pool, at the mailbox, or any place
the last 15 digits of the last number dialed.
within the operating range of the charging cradle.
2 If you move out of the charging cradle's operating
Press SEND to dial.
range, you may hear a triple beep warning tone
and/or static interference. Move closer to the
charging cradle to deactivate the alarm and
prevent disconnection. If you remain out of range
PAGING THE HANDSET FROM
for too long, the CP-2070 will disconnect from
THE CHARGING CRADLE
the line.
PAGE
1 Press on the charging cradle. The If the handset loses its security code, you will
base unit will issue beeps to confirm that also hear an alarm tone. To reset this security
the paging signal to the HS has been code, place the handset in the charging cradle for
enabled. You will hear the handset ring. a few seconds. Pick up the handset and try your
call again.
2 PAGE
To cancel the page, either press
Interference from other appliances may also
TALK
again or twice on the handset or
cause the alarm to sound. To prevent
place the handset in the charging cradle.
interference, move the charging cradle to
NOTE: another location and raise its antenna.
After seven rings the page will stop.
D
1 Once you hear the confirmation tone, you
"BLOCKED" AND
TALK
can press to answer the call and
"UNAVAILABLE" MESSAGES
automatically retain all the Caller ID
information received.
If a caller chooses to partially or completely
"block" Caller ID information, a message will
NOTE:
If you press TALK before you hear the Caller ID appear on the display indicating that the name
confirmation tone, the Caller ID information for that
and/or phone number has been blocked. If, for
call will be lost. any other reason, the name and/or number
information is currently not available from your
ANSWERING CALL WAITING
local phone company, an "Unavailable" message
will appear on the display. The time and date
CALLER ID CALLS
information for the call will still be recorded into
If you subscribe to a Call Waiting Caller ID service
the CP-2070's memory.
with your telephone company and you program
DIALING STORED CALLER ID
Call Waiting Caller ID to "ON," the CP-2070 can
receive a Caller ID call while you are on the line
NUMBERS
with another party.
The CP-2070 allows you to place calls using
1 If a second call comes while you are on the
stored Caller ID information.
phone, your CP-2070 will beep.
1 CALLER ID
Press . (You may press TALK
2 You can now view the LCD screen to see the
first if you wish. Caller ID can be dialed
name and number of the incoming caller.
from off hook mode or on hook mode).
You can decide whether to answer the
second call or ignore it and continue with 2
Locate the desired numbers by scrolling
the first call.
through saved Caller ID information using
DOWN UP ARROW KEY
the or .
3 If you choose to take the second call, press
(Holding down the DOWN or UP ARROW
FLASH
to answer it.
KEYS will automatically fast scroll through
4 FLASH Caller ID records).
You may continue to press to
switch between the two calling parties
3
SEND .
indefinitely. Press
SAVING CALLER ID
4
If your area code is set to 000 in the
INFORMATION
CP-2070 the LCD will display the first of the
three different dialing options. Press the
The CP-2070 automatically saves up to 50 Caller
UP DOWN ARROW KEY
or to view the
ID entries. Any Caller ID information (name,
rest of the dialing option.
phone number, date, time) that is transmitted will
be stored for your reference or use in the 5 Select one of the three dialing options and
autodialer and redial memory. SEND
press again . The CP-2070 will
automatically establish a dial tone and
All Caller ID names and numbers are stored in
reverse order of receipt (last call is displayed as place the call.
highest memory number.) If the memory
NOTES:
becomes full, the newest entries will be saved
If you have programmed your local area code into
and the oldest ones will be erased.
the CP-2070 before using this feature then the
CP-2070 will not prompt you for different dialing
RECEIVING CALLER ID
options. See "Programming the CP-2070" for more
information.
INFORMATION IF CALL
If no button is pressed for 30 seconds during
IS NOT ANSWERED viewing of Caller ID information the LCD will time-out
to a blank display.
Even if Caller ID calls are not answered, the
CP-2070 will automatically store the Caller ID
DELETING INDIVIDUAL
information into memory.
If the handset is in the charger, "NEW CALLERS" CALLER ID ENTRIES
will appear on the display. This message will stay
Specific Caller ID entries may be deleted.
on the screen and go away after you review the
stored Caller ID information. 1
CALLER ID
Press .
The NEW CALLS count in the LCD indicates all
CPID records not yet viewed. The NEW CALLS
2 DOWN UP ARROW KEY
Press the or
INDICATOR on the base will light until you have
to locate the entry you wish to delete.
pressed the Caller ID button to review stored
Caller ID records. 3 DELETE
Press and release . You will hear
NOTE: a double beep and the "Delete ?" message
If the handset is out of the cradle, the LCD screen will
will appear.
only say <NEW CALLERS> for 5 seconds and then
4
go blank. It will say <NEW CALLERS> again if put Press DELETE again within 5 seconds to
back into the charging cradle.
confirm. The entry will then be deleted.
REVIEWING STORED
DELETING ALL CALLER ID
CALLER ID INFORMATION
INFORMATION
If you received calls while you were away from
1
CALLER ID
your CP-2070, you can retrieve the stored Caller Press .
ID entries from memory. CPID records can also
be viewed and scrolled while off-hook (while you
2 DELETE
Press and hold until you see the
are on an active call).
"Delete All ?" message appear on the
1
Press CALLER ID . The entry for the display.
most recently received call will be
3 DELETE
displayed. Press again within 5 seconds to
confirm. All Caller ID entries will then be
The name will be displayed on the top line, the
deleted.
number on the second line, and the time and date
of that call will be displayed on the third line of the
USING THE CORDLESS PHONE
display (all information is displayed at once). The
word NEW indicates that this is a new caller ID WITHOUT CALLER ID
record. The word NEW will be displayed for each
If you do not subscribe to a Caller ID service, you
record that is being viewed for the first time. The
can still benefit from most of the CP-2070's
two digit number (example "22") in the lower right
advanced features. However, you should be
corner of the display indicates that N Johnson is
aware of the following:
your most recent caller and it is your twenty-
1. Pressing CALLER ID will simply display the
second call. This helps you keep track of how
"NO CALLS" message
many entries are currently stored in your CP-2070.
2. The Call Waiting Caller ID and Outside Line
2 DOWN UP ARROW KEY program options will have no effect.
Use the or to
DOWN NOTE:
see the other entries. scrolls
UP Certain sounds and voice pitches may occasionally
through older records and scrolls the
cause the CP-2070 to incorrectly "think" that the
opposite direction.
local phone company is sending Call Waiting Caller
ID information. Although no Caller ID data will show
up on the display, the CP-2070 may mute the phone
line for a second or so. To prevent this annoyance,
simply make sure that the Call Waiting Caller ID
program option is set to "OFF".
AUTODIAL
3 LEFT RIGHT ARROW
STORING NAMES AND Press the or
KEY
to locate the number you wish to
NUMBERS IN AUTODIAL
edit.
You may store up to 20 of your most frequently
4
UP ARROW KEY
dialed names and numbers into the autodial Press the . The entire
memory. Autodial names can be up to 16 phone number will flash. When the entire
phone number is flashing, entering a
characters long, and the accompanying phone
number on the keypad will erase the
numbers can be up to 24 digits each.
previously stored phone number from the
1
PROGRAM
Press . display and replace it.
2
AUTODIAL 5
Press . If you only wish to change a few digits,
LEFT ARROW KEY
press the to activate
RIGHT
the cursor, and then use the or
3 LEFT RIGHT ARROW
Press the or
LEFT ARROW DELETE
, , and
KEY
to locate a memory location.
NUMBER
keys to make changes.
4
Enter a telephone number on the keypad.
6 UP ARROW KEY
Press the . The entire
name will now flash. As in the previous step,
5 UP ARROW KEY
Press the to move
entering a number key (for a character
the cursor to the name field.
entry) at this point will erase the flashing
name from the display and replace it.
6
Enter the name using the keypad.
Pressing a key once displays the first
7 If you only wish to change a few letters,
upper case letter on that key. Pressing it
press the RIGHT ARROW KEY to
repeatedly will cycle through all of the
activate the cursor, and then use the
upper and lower case characters on that
RIGHT LEFT ARROW DELETE
or , , and
key. Stop when the desired character
NUMBER
keys to make changes.
appears in the display. The "1" key
provides unique characters and icons.
8
AUTODIAL
Press once the correct
information is entered and your changes
7 RIGHT ARROW KEY
Press the to
will be saved.
move the cursor one space to the right.
9
8 AUTODIAL PROGRAM
Press again when you finish Press to exit the
to save the new entry. Nothing will be programming mode.
stored until the AUTODIAL key is pressed.
9
PROGRAM ERASING AUTODIAL NAMES
Press to exit the mode.
AND NUMBERS
PROGRAMMING PAUSES IN
1 To erase numbers in autodial, press
AUTODIAL
AUTODIAL .
When you are programming numbers into the 2 DOWN UP ARROW KEY
Press the or
autodialer, the HOLD (PAUSE) key can be used to to find the autodial name and number you
insert a two-second "pause" (wait period) wish to erase.
between digits.
3 DELETE
Press and release . "DELETE ?"
For example, if you need to dial a "9" in order to
will appear in the display.
obtain an outside line, you can use the PAUSE
key to insert a two second pause for the second DELETE
4 Press again within 5 seconds to
dial tone.
confirm. The entry will then be deleted.
1 9 PAUSE/HOLD
Just press " ", , and
then the number you wish to program.
ERASING ALL AUTODIAL
NAMES AND NUMBERS
USING AUTODIAL
1
If you wish to delete all Autodial names
1 AUTODIAL
Press . (You may press AUTODIAL
and numbers, press .
TALK
first if you wish. Autodial can be
2 Press and hold DELETE until "DELETE
dialed from off hook mode or on hook
ALL?" appears in the display.
mode). If phone numbers are programmed
into the autodial memory, the first
3 DELETE
programmed number will appear in the Press again within 5 seconds to
confirm. All autodialer entries will then be
display.
deleted.
2
DOWN UP ARROW KEY
Press the or
to select an autodial number.
TRANSFER CALLER ID TO
3
When you locate the number, press AUTODIAL MEMORY
SEND to dial it. The CP-2070 will
This feature allows you to transfer a phone
automatically dial the number on the
number from Caller ID memory directly into the
display.
Autodial Memory. This saves you time and
NOTE: eliminates the chance of entering an incorrect
If no button is pressed for 30 seconds during
phone number into memory. You can even edit
viewing of autodial records the LCD will time-out to a
the name and number before you complete the
blank display.
transfer.
1 Press PROGRAM . The "PROGRAM
A FASTER WAY TO USE THE MODE" display will flash on the screen.
AUTODIALER NOTE:
If you make a mistake or change your mind at any
time during this procedure, simply press PROGRAM
If you know the autodial number (01 - 20) of the
name and number that you wish to call, you can again to quit.
enter it directly.
2 Press AUTODIAL . You will see 01
1 For example, if you know that the name flashing in the lower right-hand corner of
and number of the person you are calling the display. (The rest of the display may
are stored in autodial 06 just press or may not be blank, depending on the
AUTODIAL 6 SEND
, " ", . The CP-2070 current contents of location #1).
will then establish a dial tone and dial the
3 LEFT RIGHT ARROW KEY
number. Use the or
to select the autodial location where you
wish to transfer the Caller ID number.
EDITING AUTODIAL ENTRIES (Again, the rest of the display may or may
not be blank. If it is not blank, the
contents of this location will be written
1
PROGRAM
Press .
over once you complete the transfer.)
2 4 Press CALLER ID . The most recently
UP ARROW KEY
Press the two times or
received Caller ID entry will appear in the
DOWN ARROW KEY
the five times (or
display.
just press AUTODIAL ).
E
5 DOWN UP ARROW KEY TRANSFER REDIAL NUMBER
Use the or to
select the Caller ID entry you wish to save.
TO AUTODIAL MEMORY
This feature allows you to transfer a phone
6
You can either save the entry exactly as it
number from the Redial Memory directly into the
appears, or you can edit the name and/or
Autodial Memory. If you wish, you can add a
number. To save the entry without any
name before you complete the transfer.
editing, just press AUTODIAL . To edit
the entry, press the UP ARROW KEY 1
Follow steps 1-3 under "TRANSFER
and proceed as described in the "TO EDIT
CALLER ID TO AUTODIAL MEMORY".
AUTODIAL ENTRIES" section.
2 Press REDIAL . The contents of the
Redial Memory will appear in the display.
7
When you are finished, press
PROGRAM
to exit "Program" mode.
3 Follow steps 6-7 under "TRANSFER
CALLER ID TO AUTODIAL MEMORY" to edit
and save your autodial entry.
PROGRAMMING THE CP-2070
F
PROGRAMMING OPTIONS
PROGRAM OPTION 5:
1. Ringer Tone
CALL WAITING CALLER ID
2. Autodialer (see section E)
The Call Waiting Caller ID option is factory preset
3. Local Area Code Setting
to "OFF." If you subscribe to Call Waiting Caller
4. Outside Line
ID, you should set this option to "ON," otherwise
5. Call Waiting Caller ID
6. On-Screen Help leave it off.
NOTE:
1
PROGRAM
Press .
If no button is pressed for 30 seconds during
programming functions the LCD will time-out to a
blank display.
2
UP ARROW KEY
Press the five times.
PROGRAM OPTION 1:
The "Call Waiting Caller ID" Option display
RINGER TONE
will appear.
You can select one of 4 ringer tones for the
3
CP-2070. Use the LEFT or RIGHT ARROW KEY
to turn this option ON or OFF.
1
PROGRAM
Press .
4
PROGRAM
2 UP ARROW KEY Press again to finish.
Press the once. The
words "RINGER TONE" and its current
setting (1-4) will be displayed.
3 LEFT RIGHT ARROW
Press the or PROGRAM OPTION 6:
KEYS
to select a ringer tone. The CP-
ON-SCREEN HELP
2070 will ring once to confirm the tone you
Two modes of on-screen help are available while
have selected.
you program the CP-2070. These are:
4 1. Automatic Help
PROGRAM
Press again to finish.
A help message will automatically scroll
across the screen whenever you wait 15
seconds without pressing a key. If you do not
PROGRAM OPTION 3:
wish to wait 15 seconds, you can always see
the help message immediately by pressing the
LOCAL AREA CODE SETTING
SEND key.
The CP-2070 can make returning phone calls
2. "SEND key" Help
easier for users who reside in a 7-digit dialing
The help messages (with the exception of the
area by automatically dialing stored Caller ID
initial message) will not appear unless you
numbers. In order for this feature to work
press the SEND key.
correctly, it is necessary to program your local
NOTE:
area code into the unit.
In either mode, you can stop the help message at any
1 time by pressing any key.
PROGRAM
Press .
2 Press the UP ARROW KEY three times.
TO CHANGE THE HELP
The "Area Code" program display will
OPTION
appear. (000 is the factory default setting).
1
3 PROGRAM
Use the keypad to enter the three digits of Press .
your local area code.
2
UP ARROW KEY
Press the six times.
4
PROGRAM
Press again to finish. The "Help" display will appear.
If you have the 10 or 11 digit dialing system in
3 LEFT RIGHT ARROW KEY
Use the or
your area, leave the area code setting at 000. The
to switch between the two help modes.
CP-2070 will prompt you to choose between 7,
10, or 11-digit dialing each time you make a
4
PROGRAM
Press again to finish.
caller ID call.
PROGRAM OPTION 4:
OUTSIDE LINE
If your telephone system requires that you enter
an extra digit in order to obtain an outside line,
the CP-2070 can dial this digit for you automa-
tically whenever you dial a stored Caller ID
number. This may be useful if you use your
CP-2070 at a business that uses a PBX telephone
system.
1
PROGRAM
Press .
2 UP ARROW KEY
Press the four times.
The "Outside Line" display will appear.
3 LEFT RIGHT ARROW KEY
Use the or
to select a digit.
4
PROGRAM
Press again to finish.