Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell PW7K1R1
Summary of Contents for Honeywell PW7K1R1
- Page 1 PW7K1R1 INSTALLATION AND SPECIFICATIONS Install Guide...
- Page 2 All product and brand names are the service marks, trademarks, registered trademarks, or registered service marks of their respective owners. Printed in the United States of America. Honeywell reserves the right to change any information in this document at any time without prior notice.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Chapter 1 - Installation And Specification ..........1 General............................1 PW7K1R1 Hardware....................... 2 Reader wiring..........................3 Door Strike Relay Wiring ....................... 4 Communication Wiring ......................5 Address Baud Rate and Encryption Configuration Switch ........6 Status LEDs ..........................7 Specifications.......................... - Page 4 (This page is intensionally left blank) Installation Guide, Document 800-26499...
-
Page 5: Chapter 1 - Installation And Specification
SPECIFICATION General The PW7K1R1 reader interface provides a solution to the OEM system integrator for interfacing to a TTL (D1/D0, Clock/Data), F/2F or RS-485 device, and door hardware. It also provides a tri-stated LED control and buzzer control. Two Form-C contact relay outputs may be used for strike control or alarm signaling. -
Page 6: Pw7K1R1 Hardware
PW7K1R1 Hardware The PW7K1R1 requires filtered 12 to 24 Vdc ± 10% for power. Two inputs are typi- cally used for door contact and exit push button monitoring. End of line resistors are required input supervision, shown below. Note: The input power is passed through to the reader terminal strip and is available for powering a reader. -
Page 7: Reader Wiring
Reader wiring The reader port supports a reader with TTL (D1/D0, Clock/Data), F/2F, or 2-wire RS-485 signaling. **Refer to the reader manufacture specifications for cabling requirements. In the 2-wire LED mode the buzzer output is used to drive the sec- ond LED. -
Page 8: Door Strike Relay Wiring
Door Strike Relay Wiring The PW7K1R1 has two Form-C contact relays for controlling a door strike or other devices. See specifications section for the relay contact ratings. Load switching can cause abnormal contact wear and premature contact failure. Switching of inductive loads (strike) also causes EMI (electromagnetic interference) which may interfere with normal operation of other equipment. -
Page 9: Communication Wiring
Communication Wiring The PW7K1R1 communicates to a Honeywell Security intelligent controller (EP2500 for example) via a half-duplex multi-drop 2-wire RS-485 interface. The total cable length is limited to 4,000 feet (1,219 meters). Shielded cable of 24 AWG with characteristic impedance of 120 ohm is specified for the 2- wire RS-485 inter- face. -
Page 10: Address Baud Rate And Encryption Configuration Switch
Address Baud Rate and Encryption Configuration Switch Switches 1 to 5 select the device address. Switch 6 and 7 select the communication baud rate. Switch 8 enables encrypted communication. All other configuration settings are set via host software. SECTION OFF OFF OFF OFF OFF Address 0 OFF OFF OFF OFF ON... -
Page 11: Status Leds
SECTION OFF ON Address 25 OFF Address 26 Address 27 OFF OFF Address 28 OFF ON Address 29 OFF Address 30 Address 31 OFF OFF 115,200 BPS OFF ON 9,600 BPS 19,200 BPS 38,400 BPS Encrypted communication not required Encrypted communication required Status LEDs Power-up: All LED’s OFF Initialization:... -
Page 12: Specifications
On-line: Non-encrypted communication: 1 second rate, 80% ON, 20% OFF Encrypted communication: .1 S ON,.1 S OFF,.1 S ON,.1 S OFF,.1 S ON,.1 S OFF,.1 sec ON,.3 S OFF D1 LED Error Indication: Waiting for the downloaded of the application firmware:.1 S ON,.1 S OFF D2 LED: SIO Communication Port Status: Indicates communication activity on the SIO communication port Specifications... -
Page 13: Warranty
5 to 95 % RHNC Warranty Honeywell Security warrants the product is free from defects in material and work- manship under normal use and service with proper maintenance for one year from the date of factory shipment. Honeywell Security assumes no responsibility for products damaged by improper handling or installation. - Page 14 (This page is intentionally left blank) Installation Guide, Document...
- Page 16 Honeywell Integrated Security, 135 W. Forest Hill Avenue Oak Creek, WI 53154 United States 800-323-4576 414-766-1798 Fax www.security.honeywell.com ™ Document 800-26499 11/2020...