Honeywell PC8900A Manual page 32

Canceling Program Settings.
Each period can be canceled.
6. Canceling Period
a. Press DAY until the desired day appears in the
display.
SYSTEM
CHECK
DAY
SET SYSTEM
CLOCK
HEAT OFF COOL DAY
SELECT
HUMIDITY
PERIOD TIME
TIME
CANCEL
b. Press and hold SELECT PERIOD until the desired
period to cancel for that day appears in the display.
SYSTEM
CHECK
SELECT
PERIOD
SET SYSTEM
CLOCK
HEAT OFF COOL DAY
SELECT
HUMIDITY
PERIOD TIME
TIME
CANCEL
c. Press CANCEL. The time and temperature disap-
pears from the display.
SYSTEM
CHECK
CANCEL
SET SYSTEM FAN
CLOCK HEAT OFF COOL DAY AUTO ON CIRC
SELECT
PERIOD HUMIDITY VENTILATE
TIME
TIME
CANCEL
d. Press RUN to return to normal operation.
SYSTEM
CHECK
RUN
SET SYSTEM
CLOCK HEAT OFF COOL
SELECT
PERIOD HUMIDITY
CANCEL
Review Program Settings and Current Readings
1. Review All of Program Settings
IMPORTANT
Changes can be made to the program when using
this review process.
— Press SELECT PERIOD to enter the program.
SYSTEM
CHECK
SELECT
PERIOD
SET SYSTEM
CLOCK
HEAT OFF COOL DAY AUTO ON CIRC
SELECT
HUMIDITY VENTILATE
PERIOD TIME
TIME
CANCEL
— Press DAY for each day of the week and press
SELECT PERIOD to review each period. The display
shows the day, period, time, temperature setpoints,
fan and vent settings.
SYSTEM
CHECK
DAY
SET SYSTEM
CLOCK HEAT OFF COOL DAY AUTO ON CIRC
SELECT
PERIOD HUMIDITY VENTILATE
TIME
TIME
CANCEL
— Press RUN to exit the review.
SYSTEM
CHECK
RUN
SET SYSTEM
CLOCK HEAT OFF COOL
SELECT
PERIOD HUMIDITY
CANCEL
68-0173—3
PM
FAN HEAT/COOL
SETPOINTS
AUTO ON CIRC
VENTILATE HOLD THU LEAVE
RUN
PM
FAN
HEAT/COOL
SETPOINTS
AUTO ON CIRC
VENTILATE HOLD THU RETURN
RUN
HEAT SETPT
HEAT/COOL
SETPOINTS
MON
HOLD
RUN
AM
FAN HEAT/COOL
DAY AUTO ON CIRC SETPOINTS
MON
VENTILATE HOLD
TIME
TIME
RUN
M6230
HEAT SET PT COOL
AM
FAN HEAT/COOL
SETPOINTS
MON
HOLD WAKE
RUN
HEAT SET PT COOL
AM
FAN HEAT/COOL
SETPOINTS
WAKE
HOLD SAT
RUN
AM
FAN HEAT/COOL
DAY AUTO ON CIRC SETPOINTS
MON
VENTILATE HOLD
TIME
TIME
RUN
M6230
2. Review Current Setpoints and Readings
Use the following instructions to check the setpoints for the
current period only and to check the actual humidity and
outdoor readings.
NOTE: Return to the program at any time by pressing RUN.
a. Press CHECK to display the current humidity or
outside temperature (if outside sensor is installed).
M6249
CHECK
M6250
b. Press CHECK again to display the current humidity
reading.
COOL
CHECK
RETURN
M6251
c. Press HUMIDITY to display the setpoint.
HUMIDITY
d. Press CHECK to display two temperatures and
HEAT SET PT or COOL SET PT in the display.
CHECK
e. Press HEAT/COOL SETPOINT to display the other
setpoint.
HEAT/COOL
SETPOINTS
f. Press CHECK again to display the current FAN set-
M6234
ting.
CHECK
g. Press CHECK again to display the current VENT
setting.
M6235
CHECK
32
SYSTEM
CHECK
SET SYSTEM FAN HEAT/COOL
CLOCK DAY SETPOINTS
HEAT OFF COOL AUTO ON CIRC
SELECT
HUMIDITY VENTILATE HOLD
PERIOD TIME
TIME
CANCEL RUN
OR
SYSTEM
CHECK
SET SYSTEM FAN HEAT/COOL
CLOCK HEAT OFF COOL DAY AUTO ON CIRC SETPOINTS
SELECT
PERIOD HUMIDITY VENTILATE HOLD
TIME
TIME
CANCEL RUN
SYSTEM
CHECK
SET SYSTEM FAN HEAT/COOL
CLOCK DAY SETPOINTS
HEAT OFF COOL AUTO ON CIRC
SELECT
HUMIDITY VENTILATE HOLD
PERIOD TIME
TIME
CANCEL RUN
SYSTEM HEAT COOL SET PT
CHECK
SET SYSTEM FAN HEAT/COOL
CLOCK SETPOINTS
HEAT OFF COOL DAY AUTO ON CIRC
SELECT
HUMIDITY VENTILATE HOLD
PERIOD TIME
TIME
CANCEL RUN
SYSTEM
HEAT SET PT COOL
CHECK
SET SYSTEM FAN HEAT/COOL
CLOCK SETPOINTS
HEAT OFF COOL DAY AUTO ON CIRC
SELECT
HUMIDITY VENTILATE HOLD
PERIOD TIME
TIME
CANCEL RUN
SYSTEM
CHECK
SET SYSTEM FAN HEAT/COOL
CLOCK HEAT OFF COOL DAY AUTO ON CIRC SETPOINTS
SELECT
PERIOD HUMIDITY VENTILATE HOLD
TIME
TIME
CANCEL RUN
SYSTEM
CHECK
SET SYSTEM FAN HEAT/COOL
CLOCK DAY SETPOINTS
HEAT OFF COOL AUTO ON CIRC
SELECT
HUMIDITY VENTILATE HOLD
PERIOD TIME
TIME
CANCEL RUN
M6200
M6252
M6253
M6255
M6256
FAN
AUTO
M6257
M6258