Advertisement
Quick Links
NEC Installation
PROJECTOR COMMUNICATIONS KIT
PLEASE READ THIS DOCUMENT FOR IMPORTANT
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: NEC
Included Communications Adapter(s):
Quantity
1
1
1
1
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER'S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE " " IN THE "CONFIG AS" COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
CONFIG
MODEL
AS
NEC XG
NEC/Runco
NEC MT Series
NEC GT 2000
NEC host comm*
NEC GT 1150
* As of printing: MT1045/1040, XT5000, VT440/540
Extron • System 4 xi xi xi xi xi Switcher Series • User's Manual • P/N 68-413-02 Rev. E
SYSTEM 4xi xi xi xi xi
ATTENTION!
INSTALLATION INSTRUCTIONS
Part Number
26-472-01
26-458-01
26-494-01
26-467-01
SW1
1
2
3
4
off on on off
off on on off
off on off on
off on off on
off on off on
off on off on
Configuration and Connections
Description
ADP, UNV, "D"
ADP, NEC MT
ADP, UNV, "K"
ADP, UNV, "A"
NEC XG
SW2 SW3 SW4 SW5 SW6
0
0
4
F
0
0
7
5
0
0
0
F
0
0
4
E
0
0
5
E
0
0
5
E
PROJ
COMM
CABLE
ADAPTER
0
J9
26-472-01
0
J9
26-472-01
0
J15
26-458-01
0
J15
26-494-01
0
J15
26-467-01
0
J15
26-467-01
Page 1
Advertisement
Related Manuals for NEC 4xi NEC
Summary of Contents for NEC 4xi NEC
- Page 1 SYSTEM 4xi xi xi xi xi PROJECTOR COMMUNICATIONS KIT ATTENTION! PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATION INSTRUCTIONS THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS: Kit Type: NEC Included Communications Adapter(s): Quantity Part Number Description 26-472-01 ADP, UNV, “D”...
- Page 2 1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the NEC/Runco or NEC XG projector. Apply power to the System 4xi and do the following: a. Press to display the M on the LCD screen.
- Page 3 9. Apply AC power to the System 4xi. ____________ For the NEC XG: always apply AC power to the projector and place it in Stand- by power before applying AC power to the System 4 xi . This procedure must be followed anytime AC power to the system has been interrupted or the CC cable detached.
- Page 4 NEC Installation Configuration and Connections Example 1: System 4 with SW4 ARMX or SW6 ARMX Switcher and Projector in SW_LEVEL 1 Mode NEC SLOT EXTRON SYSTEM 4 (Host) ASSIGNMENT (SW_LEVEL 1) EXTRON CHANNEL NUMBER NEC SLOT M01 M02 M03 M04...
- Page 5 Channel List Display for an NEC Projector System 4xi xi xi xi xi - NEC/Runco and NEC XG Projector Connections Use the following diagrams as a guide when connecting the System 4xi to an NEC/Runco or NEC XG projector. Refer to NEC/Runco or NEC XG documentation to continue the installation.
- Page 6 CC 50' Male 15-Pin Connecting the System 4 xi xi xi xi xi to an NEC XG 135 Projector Extron • System 4 xi xi xi xi xi Switcher Series • User’s Manual • P/N 68-413-02 Rev. E Page 6...
- Page 7 System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the NEC MT Series projector. Apply power to the System 4xi and do the following: a. Press to display the M on the LCD screen.
- Page 8 9. Apply AC power to the System 4xi. System 4xi xi xi xi xi - NEC MT Series Projector Connections Use the diagram below as a guide when connecting the System 4xi to the NEC MT Series Projector. Refer to NEC documentation to continue the installation.
- Page 9 Connecting System 4xi xi xi xi xi to NEC GT 2000 (or equivalent) Projector If the System 4xi is already configured for an NEC GT 2000 projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board.
- Page 10 9. Apply AC power to the System 4xi. System 4xi xi xi xi xi - NEC GT 2000 Projector Connections Use the diagram below as a guide when connecting the System 4xi to the NEC GT 2000 Projector. Refer to NEC documentation to continue the installation.
- Page 11 Connecting System 4xi xi xi xi xi to NEC XT 5000 (or equivalent) Projector If the System 4xi is already configured for an NEC XT 5000 projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board.
- Page 12 9. Apply AC power to the System 4xi. System 4xi xi xi xi xi - NEC XT 5000 Projector Connections Use the diagram below as a guide when connecting the System 4xi to the NEC XT 5000 Projector. Refer to NEC documentation to continue the installation.