Arris RUCKUS T811-CM Quick Setup Manual

T811-CM Access Point
Quick Setup Guide
NOTE: The minimum software revision for the T811-
CM is SmartZone (SZ) 3.4.2, or 3.6.1, or later. (SZ 3.5.x
and 3.6 do not support the T811-CM).
This Quick Setup Guide provides brief instructions on how
to field-install the Ruckus Wireless T811-CM access point
(AP). For detailed information on planning the
installation, performing a site survey, and operating the
T811-CM, refer to the T811-CM Cable Modem Access Point
Installation Guide, available at https://
support.ruckuswireless.com.
WARNING! Only trained and qualified personnel
should be allowed to install, replace, or service this
equipment.
WARNING! Installation of this equipment must comply
with local and national electrical codes.
CAUTION! Make sure that you form a 80mm - 130mm
(3"-5") drip loop in any cable that is attached to the AP
or the building. This will prevent water from running
along the cable and entering the AP or the building
where the cable terminates.
CAUTION! Be sure that grounding is available and that
it meets local and national electrical codes. For
additional lightning protection, use lightning rods and
lightning arrestors.
CAUTION! Make sure that proper lightning surge
protection precautions are taken according to local
electrical code.
WARNING! Ruckus Wireless strongly recommends that
you wear eye protection before mounting the T811-
CM.
Copyright © 2018 ARRIS Enterprises LLC. All rights reserved.
Published October 2018, Part Number 800-71744-001 Rev C
This Guide in Other Languages
• 请从以下网站获得该指南的简体中文版
support.ruckuswireless.com.
• Vous trouverez la version française de ce guide à
l'adresse suivante https://support.ruckuswireless.com.
• このガイドの日本語版は https://
support.ruckuswireless.com でご覧ください。
• 이 가이드의 한국어 버전은 웹 사이트
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
• Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
• Puede ver la versión en español (América Latina) de
esta guía en https://support.ruckuswireless.com.
Before You Begin
Before deploying Ruckus Wireless products, please check
for the latest software and the release documentation.
• Release Notes and other user documentation are
available at http://support.ruckuswireless.com/
documents.
• Software upgrades are available at http://
support.ruckuswireless.com/software.
• Open source information is available at
opensource.ruckuswireless.com.
• Software license and limited warranty information are
available at http://support.ruckuswireless.com/
warranty.
Before deploying your Ruckus Wireless Access Point,
verify that all items listed in Package Contents are
included in the package. If any item is damaged or
missing, notify your authorized Ruckus Wireless sales
representative. Also, make sure that you have the
required hardware and tools.
Required Hardware and Tools
• No. 2 Phillips screwdriver bit
– Torque screwdriver (Ranges from 7 to 40 in-lbs)
• Small flat-blade screwdriver
• Torque wrench and torque screwdriver with sockets
– 7/16 wrench for F connector (30 in-lbs)
– 11mm socket for attenuation and impedance
matching caps (35 in-lbs)
– 19mm socket for Strand nut (16 to 20 ft-lbs) and F-
connector stinger (40 in-lbs)
• Long-nose pliers
• Electrical wire stripping and terminal crimping pliers
• Cable strand
https://
Package Contents
A Ruckus Wireless T811-CM package contains the items
listed below:
• Ruckus Wireless T811-CM unit with cable strand
hangers, includes one 12mm long stainless steel M6x1
earth ground panhead screw with split lock and flat
(https://
washers
• A one-meter green/yellow earth ground wire with ring
terminal
• Safety cable kit
• Cable gland/cable gland extender:
– 2 cable glands
– Cable gland extender
– Dual-hole cable gland insert for zip cord SFP fiber
• Service Level Agreement/Limited Warranty Statement
• Regulatory Statement
• Declaration of Conformity, if required
• T811-CM Access Point Quick Setup Guide
Mounting Instructions
http://
AP and CM MAC Addresses, Connectors
and Ground Point
The T811-CM MAC address label lists separate addresses
for the internal AP and the cable modem (CM).
The MAC address label (1 in the Figure below) is mounted
on the end of the T811-CM with the F type connector and
the ground screw (2 and 3 in the Figure). The following
table describes the label, connector and the ground point
screw.
FIGURE 1 T811-CM MAC address label, F type connector and
ground point
Page 1 of 4