Lanpro LP-N24 Manual
123 manual, ptp and mtp mode installation
Hide thumbs
Also See for LP-N24:
- User manual (60 pages) ,
- Manual (12 pages) ,
- Installation instructions (5 pages)
Related Manuals for Lanpro LP-N24
Summary of Contents for Lanpro LP-N24
- Page 1 Wireless - Equipment LP-N24, 123 Manual, PTP and MTP mode Installation. LPN24_M123_ENC01W LP-N24 123 Manual, PTP and MTP mode Installation. www.lanpro.com...
- Page 2 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation This document´s intention is to help the user setup the LP-N24 in Point to Point, and Point to Multi-Point modes. In order to perform these connections, two(2) or more LP-N24´s are needed.
- Page 3 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation The figures 2 to 5 show examples of PTP and MTP possible connections with the LP-N24. Figure 2 Figure 3 Figure 4 Figure 5 www.lanpro.com...
- Page 4 1. Please review package contents (Figure 7). Figure 7 II.1 .2. Please turn the equipment over and take note of the Mac Addresses of both LP-N24´s involved. In figure 8, you can see where to find them on the printed label.
- Page 5 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation II.2. “A” Network LP-N24 configuration. II.2 .1. Connect power as shown in figure 9. Figure 9 II.2 .2. Connect your PC to a LAN port of the LP-N24 as shown in figure 10.
- Page 6 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation II.2 .4. Please go to your network card Properties and change the IP address as shown in figures 12 and 13. Figure 12 Figure 13 II.2...
- Page 7 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation II.2 .8. The configuration window will pop-up, select option: Next, as shown in figure 16. Figure 16 II.2 .9. Select option that corresponds to your Internet Service Provider (ISP), (Most of them recommend Dynamic IP), select: Next as shown in figure 17.
- Page 8 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation II.2 .11. A Window named: Network Status pops-up showing the WAN connection status, it obtains the IP Address like the one shown in figure 19 (This address is for reference purposes only), if not, please verify the cable connection from the LP-N24´s WAN port to the...
- Page 9 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation II.2 .13. Proceed to input the wireless LAN client password in the field named: Pass Phrase and select: Apply, as shown in figure 22. Figure 22 II.2...
- Page 10 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation II.2 .16. Proceed to input the encryption phrase for WDS and the MAC address of the equipment that will be connected to it (Network B), then select: Apply, as shown in figure 25.
- Page 11 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation With the steps already followed, you are now through with the first part of the configuration. This equipment must remain turned on for the second part of the configuration to take place which is explained in the following paragraphs.
- Page 12 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation II.3 .4. A window will pop-up asking for the user and password, by default, user is: admin and the password is: admin; select: OK, as shown in figure 32.
- Page 13 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation II.3 .7. Proceed to input the WLAN password in the field: Pass Phrase and select: Apply, as shown in figure 35. Figure 35 II.3 .8. In this step, we will change the IP address of the LP-N24 of the B network.
- Page 14 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation II.3 .10. Input the new IP address in your browser as shown in figure 38. Figure 38 II.3 .11. Input your User and Password and selct : OK, as shown in figure 39.
- Page 15 Wireless - Equipment - 2.4 GHz - LP-N24, 123 Manual, PTP and MTP mode Installation II.3 .14. Select the Type of Encryption for WDS, remember to use the same you configured in paragraph 18, because this is the link between both networks (A and B);...
- Page 16 II.3 .19. Once these steps are finished you will have configured a Point to Point network with Access to both LP-N24 for wireless connections. In order to test its operation, open a command window and send a PING to the destination router, in this example we use: 192.168.0.1, as shown in figure 30.