Setting Of Menu Switch (Menu); Menu Switch Composition - Canon Super G3 3rd Line FAX Board-AE1 Service Manual

5
Service Mode Service Mode > Setting of Menu Switch (MENU) > Menu Switch Composition

Setting of Menu Switch (MENU)

Menu Switch Composition

Sssw Menu Num Ncu Type ISDN
001
xxxxx
002
xxxxx
003
xxxxx
004
xxxxx
005
xxxxx
006
xxxxx
007
xxxxx
008
xxxxx
No. Function
005 NL equalizer
006 telephone line monitor
007 transmission level (ATT)
008 V.34 modulation speed upper limit
009 V.34 data speed upper limit
005: NL Equalizer
Use it to enable-disable the NL equalizer.
If errors occur often during communication because of the condition of the line, enable (ON)
the NL equalizer.
NOTE:
Any of the following error codes may be indicated at time of transmission because of the line
condition
##100, ##101, ##102, ##104, ##201, ##281, ##282, ##283, ##750, ##755, ##765, ##774,
##779, ##784, ##789
Any of the following error codes may be indicated at time of transmission because of the line
condition
##103, ##107, ##114, ##201, ##790, ##793
5 Service Mode > Setting of Menu Switch (MENU) > Menu Switch Composition Service Mode
Print Clear Test Report
<READY>
<1/3>
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
OK
F-5-11
Range of settings
1: ON, 0: OFF
from 0 to 3
from 8 to 15 (ex: 15= -15 dBm)
0:3429, 1:3200, 2:3000, 3:2800, 4:2743, 5:2400
from 0 to 13
006: Telephone Line Monitor
Use it to the telephone line monitor function:
0 (DIAL): generate the monitor sound of the telephone line using the speaker from the start of
transmission to DIS.
1: generate the monitor sound of the telephone line using the speaker from the start of
communication to the end of it.
2: not used
3 (OFF): do not generate the monitor sound of the telephone line usng the speaker.
007: ATT Transmission Level
Use it to set the transmission level (ATT).
Raise the transmission level if errors occur frequently at time of communication because of
the condition of the line. (It means close to 8)
NOTE:
Any of the following error codes may be indicated at time of transmission because of the line
condition
##100, ##101, ##102, ##104, ##201, ##280, ##281, ##282, ##283, ##284, ##750, ##752,
##754, ##755, ##757, ##759, ##760, ##762, ##764, ##765, ##767, ##769, ##770, ##772,
##774, ##775, ##777, ##779, ##780, ##782, ##784, ##785, ##787, ##789
Any of the following error codes may be indicated at time of reception because of the line
condition
##103, ##106, ##107, ##201, ##793
008: V.34 Modulation Speed Upper Limit
T-5-18
Use it to set an upper limit to the modulation speed (baud rate) for the V.34 primary channel.
When '4 (2743 baud)' is selected, the actual communication is executed with 2400 baud.
009: V.34 Data Speed Upper Limit
Use to set an upper limit to the data transmission speed for the V.34 primary channel between
2.4K and 33.6K bps in increments of 2400 bps. (0: 2.4K to 13: 33.6K bps).
5-13
5-13