Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zanussi ZWF71463W
Summary of Contents for Zanussi ZWF71463W
- Page 1 User Manual GETTING STARTED? EASY. ZWF71463W EN User Manual Washing Machine...
-
Page 2: Safety Information
VISIT OUR WEBSITE TO: Get usage advice, brochures, trouble shooter, service and repair information: www.zanussi.com/support SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage. -
Page 3: Safety Instructions
The ventilation opening in the base must not be covered by a • carpet, mat, or any floor covering. The appliance must be connected to the water mains using the • new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. -
Page 4: Water Connection
• Make sure not to cause damage to the mains • Follow the safety instructions on the detergent plug and to the mains cable. Should the mains packaging. cable need to be replaced, this must be carried • Do not put flammable products or items that are out by our Authorised Service Centre. -
Page 5: Product Description
PRODUCT DESCRIPTION APPLIANCE OVERVIEW Worktop Detergent dispenser Control panel Door handle Rating plate Quick Reminder sticker Feet for levelling the appliance The rating plate reports the electrical ratings (C), model name (A), product number (B) and serial number (D). Mod. xxxxxxxxx Prod.No. -
Page 6: Installation
Maximum Load Cotton 7 kg Spin Speed Maximum spin speed 1400 rpm Spin drying performance Remaining moisture 48 % 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 2) At the end of spinning phase. INSTALLATION hose from the hose holders. - Page 7 4. Connect the water inlet hose to the cold water We recommend that you keep tap with 3/4'' thread. the packaging and the transit Water drainage bolts for any transport of the appliance. The drain hose should stay at a height of no less than 60 cm and not more than 100 cm.
-
Page 8: Electrical Connection
ø16 W011 Connect the drain hose to the spigot and tighten it with a clamp. Make sure that the drain hose makes 4. To a stand pipe with vent hole - Insert the drain a loop to prevent particles going into the appliance hose directly into a drain pipe. -
Page 9: Special Features
CONTROL PANEL SPECIAL FEATURES area for regular maintenance and cleaning. Refer to chapter 'Care and Cleaning' for best maintenance Your new washing machine meets all modern and care of the appliance. requirements for an effective treatment of laundry with low water, energy and detergent consumption The AutoSense System automatically adjusts the and will care for fabrics. -
Page 10: Programme Chart
DISPLAY A. The time area: • : the programme duration • : the "finish in" time • : the alarm codes • : the message of error • : the programme is completed. B. The child lock indicator: • The indicator comes on when you activate Finish In this device. - Page 11 Maximum load Programme Programme description Reference spin Temperature range (Type of load and soil level) speed 1 kg A very short cycle for cotton and synthetic items with Refresh 20 1200 rpm light soil level or worn only once. 40°C - 30°C 2 kg Special programme for cotton, synthetic and mixed fabrics Mix 20°...
- Page 12 • Set this option to deactivate all spin phases. The related indicator comes on. Only the drain phase is available. • The related indicator comes on. RINSE ONLY • Set this option for very delicate fabrics. With this option you can perform only a last rinse of •...
-
Page 13: Before First Use
• The programme is completed. Activate this option after you touch the button • The appliance has a malfunction. the buttons are locked (except for the button To deactivate/activate the acoustic signals, touch the buttons at the same time for 4 This option stays active even when you seconds. - Page 14 When the flap is in position B and you want to use Compartment for liquid additives powder detergent: (fabric conditioner, starch). 1. Remove the drawer. 2. Adjust the flap in position A. CAUTION! Do not 3. Put back the drawer in the recess. exceed the MAX level.
- Page 15 CANCELLING A PROGRAMME After approximately 15 minutes from 1. Press the button On/Off for some seconds to the start of the programme: cancel the programme and to deactivate the • The appliance adjusts automatically appliance. the programme duration agree with 2.
-
Page 16: Auto-Off Option
AUTO-OFF OPTION • The door lock indicator is on. The indicator The AUTO-OFF stand-by option automatically of button flashes. The door stays locked. deactivates the appliance to decrease the energy • You must drain the water to open the door. consumption. -
Page 17: Stubborn Stains
STUBBORN STAINS Insufficient detergent may cause: • unsatisfactory washing results, For some stains, water and detergent is not • the wash load to turn grey, sufficient. • greasy clothes, We recommend that you pre-treat these stains • mould in the appliance. before you put the items in the appliance. -
Page 18: Maintenance Wash
DESCALING After each cycle, keep the door and the detergent dispenser slightly ajar to get air circulation and dry If the water hardness in your area is the humidity inside the appliance: this will prevent high or moderate, we recommend that mildew and odours. -
Page 19: Cleaning The Detergent Dispenser
CLEANING THE DETERGENT DISPENSER CLEANING THE INLET HOSE AND THE VALVE FILTER 45° 20° FROST PRECAUTIONS If the appliance is installed in an area where the temperature can be less than 0 °C, remove the remaining water from the inlet hose and the drain pump. -
Page 20: Troubleshooting
TROUBLESHOOTING WARNING! Refer to Safety chapters. ALARM CODES AND POSSIBLE FAILURES The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the tables). WARNING! Deactivate the appliance before carrying out any check. With some problems, the display shows an alarm code and the button may flash continuously: Problem... - Page 21 If the display shows other alarm codes, deactivate and activate the appliance. If the problem continues, contact the Authorised Service Centre. In case of different problem with the washing machine check the table below for possible solutions. Problem Possible solution •...
-
Page 22: Consumption Values
Problem Possible solution Too much foam in the • Reduce the quantity of detergent. drum during the wash- ing cycle. After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the Authorised Service Centre. The necessary data for the service centre on the rating plate. -
Page 23: Environmental Concerns
Approximate Energy con- Water con- programme du- Programmes Load (kg) sumption sumption (litre) ration (mi- (kWh) nutes) Wool/Handwash 0.45 30°C 1) This programme at 60 °C with a load of 7 kg is the reference programme for energy label data, in com- pliance with UAE. - Page 24 WWW.ZANUSSI.COM/SHOP...