Summary of Contents for NAMCO TEKKEN TAG TOURNAMENT
Page 2
INTRODUCTION Thank you very much for purchasing TEKKEN TAG TOURNAMENT PC BOARD KIT (hereafter called “this product”). This operation manual explains the following: Installing and connecting this product to a general-purpose game cabinet (hereafter called “cabinet”) safely, Dismounting, safekeeping, and transporting this product safely,...
1. SAFETY PRECAUTIONS - Be sure to read this part for safe use - To the owner: connect, to adjust for operation, to operate, to inspect, to clean, to troubleshoot, to disassemble. to keep, to transport and to dispose, direct such a person(s) to read the applicable part of this manual before conducting the task and to observe the instructions.
Do not perform any works with wet hands. Otherwise it may cause an electrical shock. conducting any works such as installation and connection (except transferring the data to be displayed on the Namco-made CYBERLEAD cabinet), inspection, cleaning, troubleshooting, disassembling. Otherwise an electrical shock may happen.
l-3-3 Safety Precautions When Operating operation. Then unplug the power cord from an electrical outlet and contact your distributor. If the machine is kept operating without solving the trouble, it may cause an electrical shock or fire. procedure specified in this operation manual (Ref. “5. INSTALLING AND CONNECTING” on p-9) before operation.
TABLE OF CONTENTS SAFETY PRECAUTIONS - Be sure to read this part for safe use - ............ l-1 Level ofDanger ..........................1-2 Readers of this operation manual ....................Safety Precautions........................... 1-3-1 General Safety Precautions....................l-3-2 Safety Precautions When Installing and Connecting............l-3-3 Safety Precautions When Operating ..................
Page 7
6-2 Display Test (Check/adjustment of the display) ................79 _ Operation ......................6-2-l Common 6-2-2 CONVERGENCE (Checking/adjusting the size, position, aspect ratio, distortion of the picture) ..........................6-2-3 COLOR EDIT, COLOR BAR (Adjustment the shade and tone balance of the picture signal outputted by the PC board) 6-3 SWITCH TEST..
2. SPECIFICATIONS Description Item Corresponding Standard standard * 1 Weight Input power source [Connected to JAMMA standard terminal ] [Connected to JAMMA VIDEO standard (JVS) renninal] Restriction Indoor use only Temperature : 0°C - 50°C. Humidity : 10% - 85% (no condensation) Cabinets applicable to connect corresponding to JAMMA standard C a bine ts c orre sponding to JAMMA VIDEO standard (JVS)
3. CHECK OF PACKAGE This product includes the following items: PRE-KIT A, TEKKEN TAG TOURNAMENT Part No. Description Decal, Side Panel, Right Decal, Marquee Decal, Control Panel Decal, “PUNCH” Decal, “KICK” Decal, “PLAYER 1” Decal, “PLAYER 2” Decal, Tekken Tag Tourn.
4. COMPONENTS Option switch Parts mounted side Terminal for the J Terminal for the extende edge connector cabinet corresponding to Speaker volume VIDEO standard (JVS) (Ref. p.22 for details) PC Board Wire Extended edge preventive key Extended Edge Harness...
Always turn off the power switch of the cabinet and unplug the power cord from an electrical outlet before conducting any work, except the work for “5-4-3 Transferring the data to be displayed on the Namco-made CYBERLEAD cabinet”. Otherwise an electrical shock may occur. cause a fire or electrical shock.
5-1 Before Installing (Both for m, m) the necessary to install this product as follows. prepare items Items needed Remarks Reference Operation manual attached your cabinet Check the handling of your cabinet. Countersunk head tapping screw (4 pieces) Fix the lesslocks on the install board of Chapter 5-2 pfi.m Diameter: one size smaller than the diameter of...
When setting networked head-to-head play by using two cabinets corresponding to JAMMA you can use either cabinet. Namco-made CYBERLEAD cabinet, for example In cases other PC boards are connected, remove them in accordance with the procedure described in the operation manual of your cabinet.
Page 14
Install the PC board at the center of the install board with the countersunk head tapping screws, lesslocks, spacers (unnecessary if the pan head machine screws are not too long) and pan head machine screws, through the four install holes on the PC board. pieces)’...
Connecting to the Cabinets Corresponding to the JAMMA Standard 5-3-l Checking the JAMMA Edge Connector !H Use the JAMMA edge connector attached to the cabinet to connect this product to the cabinet corresponding to the JAMMA standard. Check if the terminal numbers of the JAMMA edge connector of the cabinet conform to the table of JAMMA edge connectors below.
Page 16
Check the power source for the cabinet connecting to the JAMMA edge connector and voltage of the power source for the coin counter of the cabinet. The power source on the cabinet connected to the JAMMA edge connector should fit the following requirements: If the power source does not conform to this requirement, it may cause a fire.
5-3-3 Connecting to the Control Panel m This product has to be connected to the control panel (see below) described in the SPECIFICATIONS” (on p.6) to use. joystick button switches Turn the power of the cabinet OFF and unplug the power cord from an electrical outlet. Remove the control panel in accordance with the instmctions on “control panel”...
Page 18
Connect the wires of the extended edge harness on the following table to the terminals of PI button switch 4,5,6 and P2 button switch 4,5,6 on the control panel by soldering or fixing an applicable crimp-style terminal. Soldered side Terminal side Parts mounted side P2 button switch 4 (white/blue) P2 button switch 5 (white/purple)
Page 19
Connect the product to the speaker(s) of your cabinet in the following procedure so that the cabinet outputs the sound. First check whether your cabinet has one speaker (monaural) or two speakers (stereo). One speaker (monaural) (Al, Conduct a meaSure to prevent short-circuit, for instance, wmp the edge of the unused wire B 1) of the extended edge harness with insulating tape.
Page 20
5-3-5 Connecting to the connectors a Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet. Connect the JAMMA edge connector attached to the cabinet and the extended edge connector in the direction shown below so that the mis-insert preventive key would fit the notch of the connector slot of the PC board.
Page 21
3 Put the PC board installed on the install board into the cabinet vibration. Be careful that the PC board does not touch any harnesses or cables after being put inside the cabinet. If it is kept operating with touching to any of them, it may break down.
Connecting the Product to the Cabinet Corresponding to JAMMA VIDEO Standard (JVS) m The explanation on connection to the cabinet corresponding to the JAMvIA VIDEO standard (JVS) and on transfer of the data to be displayed on the Natnco-made CYBERLEAD cabinet is given here. First, perform the procedure of “5-2 Installing the PC Board on the Install Board of the Cabinet”...
In cases that the control panel of your cabinet is different from the figure in the previous page, replace the control panel or add/reduce button switches. If some switches are reduced, be sure to fill up the switch holes with hole caps. Check if each joystick and switch of the control pane1 is appropriately connected to each control panel connecting terminal on the cabinet with reference to the figure in the previous page and the operation manual of your cabinet.
Page 24
Connect the cables of the cabinet to the corresponding connectors of the PC board as the figure below. Audio cable Connect the one printed “white” or Video-cable If there are Iwo terminals. video cables, connect both cables to the terminals (either). Prevent short-circuit by wrapping insulating tapes around unnecessary connectors of the cabinet.
Pasting the Stickers (Both for m, m) Paste the stickers included in the package on the cabinet and install it. Title sheet A sticker B sticker Namco-made CYBERLEAD cabinet, for example Put together the POP referring to the attached operation manual, and place it appropriately.
6. ADJUSTMENT FOR OPERATION The cabinet needs to be conducted adjustment for operation (setting or altering) in order to operate game. The following items can be adjusted. Item Reference Testing switches connected to PC board 6-3 Switch Test (p.34) 6-4 Sound Test (p.35) Testing sound output and setting speakers Setting of VIDEO SYNC on the cabinet 6-5 NS Cabinet Options (p.36)
Switches, Knobs 6-l-l Adjustment The PC board has a switch and a knob for adjustment, the option switch and speaker volume. No.1 shall be used to switch the test mode/game mode. ON: Test mode Game mode No.2 shall be not used This knob adjusts the volume of the speaker sound of the cabinet.
6-l-2 Selecting the Adjusting Items Display the test menu screen on the test mode to make adjustment. Turn the power switch of the cabinet ON to display the game screen. Turn No.1 option switch (0) ON. enter the test mode only when they are switched from OFF to ON. They cannot make it enter the test mode even when they are already set ON.
Page 29
Hit the Pl S-direction joystick up or down to turn the item to be adjusted in red referring to “6- 2 Display Test” (p.28) through “6-9 Data Clear” (p.42). S-direction joystick Note: The above figure shows the pair control panel. In case of the single control panel (that is, two cabinets corresponding to the JAMMA VIDEO standard (JVS) linked for networked head-to-head play), the control panel of the cabinet on which...
6-l-3 Finishing the Test Mode After making adjustment of each item according to “6-2 Display Test” (p.28) through “6-S Data Clear” (p.42) display the test menu screen. Hit the Pl S-direction joystick up or down to turn “EXIT & SAVE” in red. Press the Pl button switch 1.
6-2-l Common Operation Perform the procedure 1 - 4 of “6-l-2 Selecting the Adjusting Items” (~28-29). Select “DISPLAY TEST’ in 3. “Color Edit” screen shall be displayed over the “diagonal” screen as follows. Color edit screen C O N V E R G E N C E PREVIOUS VALUE : P-l BUTTONS EXIT COLOR EDIT : P-l BUlTON4...
Press the Pl button switch I to go the other adjustment item. * Each time you press the switch, it shifts from “CONVERGENCE” -> “COLOR BAR” “CONVERGENCE” ..and its screen is displayed each time. control Note: The above figure shows the pair panel.
Page 33
On the “CONVERGENCE” screen, the following “cross hatch pattern” is displayed. Cross hatch pattern ENTER COLOR EDIT : P-l BLiTrON4 P - l SIART Note: The above shows the screen with the color edit non-displayed. It makes no difference if the color edit is displayed. Press the Pl button switch 2 check the size, position, aspect ratio, and distortion of the cross...
6-2-3 COLOR EDIT, COLOR BAR (Adjustment of the shade and tone balance of the picture signal outputted by the PC board) Perform the procedures 1 and 2 of “6-2-l Common Operation” (p.29) to display the “Color Edit” screen over the ‘Color Bar” screen. * If “DISPLAY TEST”...
Page 35
Hit the PI S-direction joystick to up or down to select the adjusting item out or “Contrast”, “Bright R”, “Bright G”, and “Bright B”. Note: The above figure shows the pair control panel. In case of the single control panel (that is, two cabinets corresponding to the JAMMA VIDEO standard are linked for networked head-tohead play),...
button switch Note: The above figure shows the pair control panel. In case of the single panel control (that is, two cabinets corresponding to the JAMMA VIDEO standard (NS) are linked for networked head-to-head play), the control panel of the cabinet on which the PC board is installed shall be called as Pl.
Operate each joystick and switch on the control panel one by one. The joysticks on the screen moves in accordance with the actual moves of “PI &direction joystick” and “P2 S-direction joystick”. The button on the screen is highlighted in white when the actual button switch on the control panel is pressed.
Page 38
Make adjustment according to the description on the table below with the appropriate joystick and the switch. Test/Adjustment How to operate The sound to be used in the Changing tbe sound number Hit the Pl S-direction joystick to right or left to game is selected.
Page 39
SYNC” as “Separate” for the best picture. l Namco-made CYBERLEAD cabinet corresponds to the separate signal. But if another monitor display is connected to the line output picture terminal on the back of the cabinet, set the “VIDEO SYNC” as “Composite”, because that monitor display may get poor picture under the “Separate”...
Perform “6-l-3 Finishing the Test Mode” (p.28) to exit the test mode. GAME OPTIONS (Setting of the game options) Game options such as the game difficulties shall be set here. Perform the procedure 1 - 4 of “6-l-2 Selecting the Adjusting Items” (p.26-27). Select “GAME OPTIONS”...
Page 41
( d ) LIFE BAR<lP GAME>(Life gauge in 1P play game) NORMAL ( e ) LIFE BAR<VS GAME>(Life gauge in 2P play game) ( f )ROUND TJME(Time per 1 round[second]) ( g )GUARD DAMAGE@amage at guard) little) (h )NEUTRAL GUARD(Guard in the condition that the lever is not be tilted) ( i) CHARACTER CHANGE AT CONTINUE(Changing characters at a continued play) ( k ) MUSIC IN ATTRACT(Sound...
6-7 COIN OPTIONS (Setting of play fees) Coin options such as the credit needed to play one game play shall be set here. Perform the procedure 1 - 4 of “6-l-2 Selecting the Adjusting Items” (p.26-27). Select “COIN OPTIONS” in 3. The following screen is displayed.
Page 43
COIN CHUTE I MECHANICAL VALUE (The number of coin(s) to be added when the coin switch 1 activates once) COINCOUNTAS 9 I COIN COIN CHUTE 2 MECHANICAL VALUE (The number of coin(s) to be added when the coin switch 2 activates once) COINCOUNTAS COIN COMMON...
Press the Pl start switch to remm to the test menu screen. PI, SLUL switch Note: The above figure shows the pair control panel. In case of the single control panel (that is. two cabinets corresponding to the JAMMA VIDEO standard (JVS) are linked for networked head-to-head play), the control panel of rhe cabinet on which Perform “6-l-3 Finishing the Test Mode”...
The following screen is displayed. DATA CLEAR CANCEL RANKING CLEAR Initialize the ranking daw SET DEFAULTS ALL OPTIONS options Set the value to default ALL CLEAR Clear all the data recorded EXEC : Pl -BUl-i-ON1 EXIT : Pl -START Hit the Pl 8-direction joystick up or down to select an item to erase or initialize the data out of (b) - (e) on the above figure.
Page 46
Press the Pl button switch 1 to execute the selected item. Note: The above figure shows the pair control panel. In case of the single control panel (that is, two cabinets corresponding to the JAMMA VIDEO standard (JVS) linked for networked head-to-head-play), the control panel of the cabinet on which the PC board is installed shall be called as Pl.
7. OPERATION operation. Then unplug the power cord from an electrical outlet and contact your distributor. If the machine is kept operating without solving the trouble, it may cause an electrical shock or fire. If you have to touch the PC board during operation, refer to “8. INSPECTION & CLEANING, TROUBLESHOOTING”...
8. INSP~ON&- G,TROUB~~G 8-l Inspection & Cleaning cleaning. Otherwise an electrical shock may happen. Do not conduct any works with wet hands. It may cause an electrical shock. Be sure to conduct a regular inspection and cleaning according to the following table so that the T i e Description Reference...
8-2 Troubleshooting Always unplug the power cord of the cabinet from an electrical outlet before checking this product is installed and connected on the cabinet correctly. Otherwise an electrical shock may occur. operation. Then unplug the power cord from an electrical outlet and contact your distributor. If the machine is kept operating without solving the trouble, it may cause an electrical shock or fire.
Page 51
When the trouble is not solved even after performing the procedure from 1 through 5, turn the power OFF, unplug the power cord from an electrical outlet, and contact your distributor.
9. Disassembling, Safekeeping, Transportation Disassembling -To be serviced by a qualified service technician only - may cause an electrical shock. A service technician should not be charged electricity when touching the PC board. Static electricity may cause the product breakdown or damage. Disassemble the PC board following the procedure below.
Page 53
standard cabinet, for example Remove the screws on the four comers of the PC board and disassemble the PC board from the install board. Put back the install board and close the door.
Page 56
11. APPENDIX A Control Panel Layout Template Electrical Diagram...
Page 57
N O T E S : AND BREAK ALL SHARP EDGES 2. USE MINIMUM BEND PAD11 3. MATERIAL: 16 GA (0.06 THK) CRS 4. FINISH: DE BLACK ARBI SHERWIN EQUAL 5. STAMP PART NUMBER AND REV LE”EL IN 1 8” HIGH “SING INDELIBLE INK IN APPROXIMATE POSI ON SHOWN 6.