Cisco 8540 Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Controller
  5. 8540 - Catalyst Campus Switch Router Modular Expansion...
  6. Manual

Cisco 8540 Manual

Installing the controller
Hide thumbs Also See for 8540:
Table of Contents

Advertisement

Quick Links

Download this manual
Installing the Controller
This chapter describes how to install the controller.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work
on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents. Use the statement number provided at the end of each warning to locate
its translation in the translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
•
•
•
•
•
Unpacking and Inspecting the Controller
Caution
When handling internal controller components, wear an ESD strap and handle modules by the carrier edges
only.
Tip
Keep the shipping container in case the controller requires shipping in the future.
Note
The chassis is thoroughly inspected before shipment. If any damage occurred during transportation or any
items are missing, contact your customer service representative immediately.
Unpacking and Inspecting the Controller, on page 1
Preparing for Controller Installation, on page 2
Installing the Controller In a Rack, on page 5
Initial Controller Setup , on page 9
System BIOS and Cisco IMC Firmware, on page 9
Installing the Controller
1

Advertisement

Table of Contents
loading

Related Manuals for Cisco 8540

Summary of Contents for Cisco 8540

  • Page 1 • Initial Controller Setup , on page 9 • System BIOS and Cisco IMC Firmware, on page 9 Unpacking and Inspecting the Controller Caution When handling internal controller components, wear an ESD strap and handle modules by the carrier edges only.

  • Page 2: Preparing For Controller Installation

    Installing the Controller Preparing for Controller Installation Step 1 Remove the controller from its container and save all packaging material. Step 2 Compare the shipment to the equipment list provided by your customer service representative. Verify that you have all items.
  • Page 3 Installing the Controller Installation Guidelines Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning Ultimate disposal of this product should be handled according to all national laws and regulations.

  • Page 4: Rack Requirements

    Equipment Requirements The slide rails supplied by Cisco Systems for this controller do not require tools for installation if you install them in a rack that has square 0.38-inch (9.6 mm), round 0.28-inch (7.1 mm), or #12-24 UNC threaded holes.

  • Page 5: Installing The Controller In A Rack

    Installing the Controller In a Rack Installing the Slide Rails This section describes how to install the controller in a rack using the rack kits that are sold by Cisco. Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable.
  • Page 6 Installing the Controller Installing the Slide Rails Figure 2: Front Securing Mechanism, Inside of Front End Front mounting pegs Securing plate shown pulled back to open position Rack post Step 3 Install the slide rails into the rack: a) Align one slide-rail assembly front end with the front rack-post holes that you want to use. The slide rail front-end wraps around the outside of the rack post and the mounting pegs enter the rack-post holes from the outside-front (see Figure 2: Front Securing Mechanism, Inside of Front End, on page...

  • Page 7: Installing The Cable Management Arm (Optional)

    Installing the Controller Installing the Cable Management Arm (Optional) Figure 3: Inner Rail Release Clip Inner rail release clip Outer rail attached to rack post Inner rail attached to controller Step 5 (Optional) Secure the controller in the rack more permanently by using the two screws that are provided with the slide rails.

  • Page 8: Reversing The Cable Management Arm (Optional)

    Installing the Controller Reversing the Cable Management Arm (Optional) Figure 4: Attaching the Cable Management Arm to the Rear of the Slide Rails CMA tab on arm farthest from controller CMA tab on width-adjustment slider and end of stationary outer slide rail and end of stationary outer slide rail CMA tab on arm closest to the controller Rear of controller...

  • Page 9: Initial Controller Setup

    When you upgrade the BIOS firmware, you must also upgrade the Cisco IMC firmware to the same version or the controller does not boot. Do not power off the controller until the BIOS and Cisco IMC firmware are matching or the controller does not boot.

  • Page 10: Accessing The System Bios

    Installing the Controller Accessing the System BIOS The only supported method to update the firmware is using the Cisco Host Upgrade Utility. Accessing the System BIOS You can change the BIOS settings for your controller. Detailed instructions are also printed on the BIOS screens.

Table of Contents