Honeywell Perfomance Series Quick Installation Manual

HBW4PGR1 WDR 4MP IR Bullet Camera

Quick Installation Guide

Thank you for purchasing a Honeywell Performance Series IP camera.
Follow the instructions in this guide to install and log in to your camera.
For instructions on configuring the camera, refer to the user guide on the
CD that came with your camera. If you require additional assistance, call
the number listed for your region on the back cover.

Cautions and Warnings

CAUTION THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
RISK OF ELECTRIC
CONSTITUTING A RISK OF
SHOCK
ELECTRIC SHOCK IS PRESENT
DO NOT OPEN
WITHIN THE UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
THIS SYMBOL INDICATES THAT
SHOCK, DO NOT REMOVE THE COVER.
IMPORTANT OPERATING AND
NO USER-SERVICEABLE PARTS INSIDE.
MAINTENANCE INSTRUCTIONS
REFER SERVICING TO QUALIFIED SERVICE
ACCOMPANY THIS UNIT.
PERSONNEL.
WARNING To ensure compliance with electrical safety standards, this product is
intended for use with a Listed Power Adapter marked "Limited Power
Source" or "LPS" on the unit, output rated to 12 VDC, minimum 0.33 A,
TMA=60 deg C, or from Power over Ethernet (PoE) provided by Listed
Information Technology Equipment meeting IEEE 802.3af PoE standard.
CAUTION The Ethernet connection is not intended to be connected to exposed
(outside plant) networks. Do not connect two power sources to the camera
at the same time.
CAUTION Invisible LED radiation (850 nm). Avoid exposure to beam.

Important Safeguards

•
Read and keep these instructions.
•
Confirm the installation surface can support at least three times the weight of the camera.
•
Do not aim the camera toward a bright light source for extended periods to prevent damage to the imager.
•
Avoid operating the unit under or close to unstable light sources (may cause flickering), or close to fluorescent
lamps or objects reflecting light.
• Do not touch the camera lens.
•
Do not drop the camera or subject it to physical shock.
•
Do not use a strong or abrasive detergent when cleaning the camera.
•
Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the operating
temperature is outside the recommended range of -22°F to 140°F (–30°C to 60°C).
• Do not apply power to the camera before completing installation.
Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are missing or damaged,
contact your dealer immediately.
•
Self-tapping screws (×4)
•
Camera
•
Plastic wall anchors (×4)
• Installation CD
•
Mounting template
• Quick installation guide
•
Allen key (L-wrench)
CAUTION Installation and servicing should be performed only by qualified and experienced technicians to conform
to all local codes and to maintain your warranty.

Preparing the Mounting Surface

1. Apply the mounting template to the mounting surface.
Note Observe the orientation of the cable exit notch on the bracket base. In outdoor installations, the notch
should point downward to prevent water from entering the camera housing.
2. Using the mounting template as a guide, drill four pilot holes in the mounting surface, then hammer the supplied
anchors into the holes.
3. Drill a cable entry hole in the mounting surface, then pull the required cables through the hole.
Mounting and Aiming the Camera
1. If you are using a microSD card with the camera, install it before continuing. To access the microSD card slot,
remove the panel on the underside of the camera and insert a microSD card into the microSD card slot (refer to
the picture below).
Note Press and hold the reset button abouts 10s when the camera is power on or rebooting to restore the
default settings, including the user name, password, IP address, port NO., ect.
2. Connect one end of the Ethernet cable to the RJ-45 port on the
camera.
3. If the other end of the Ethernet cable is NOT connected to a PoE
switch or NVR, connect the power connector of the camera to a 12
VDC power source.
4. If the camera is installed outdoor, you can adapt the water-proof
accessory for the network cable after the camera is secured on the
installation surface (refer to the picture on the right).
5. Attach the camera assembly to the mounting surface using the
supplied screws.