Download
Share
Print this page
Yamaha HY144-D-SRC Firmware Update Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Accessories
  5. HY144-D-SRC
  6. Firmware update manual

Yamaha HY144-D-SRC Firmware Update Manual

Hide thumbs Also See for HY144-D-SRC:

Advertisement

Quick Links

See also: Owner's Manual
HY144-D-SRC Firmware Update Guide
Thank you for choosing a Yamaha product. This guide explains how to update the HY144-D-SRC
firmware. The SRC modes can be changed by updating to the card's firmware corresponding to each
SRC mode (page 7).
■ Precautions
・ The user assumes full responsibility for the update.
・ Update the firmware components one device at a time.
・ Please note that the device may be damaged if you fail to follow these instructions
properly, or turn off the device or disconnect the cable while the update is in
progress.
・ If the update fails, and the device still does not operate correctly even after you
execute the update once again, please contact your Yamaha dealer.
・ This guide is the exclusive copyrights of Yamaha Corporation.
・ Audinate owns exclusive copyrights for the Dante firmware and its update program.
・ It is prohibited to duplicate or modify the firmware, software or this guide, in part or
in their entirety, without permission from the copyright owner.
・ The illustrations and screens as shown in this guide are for instructional purposes
only.
・ Yamaha Corporation makes no representations or warranties with regard to the use
of the software and documentation and cannot be held responsible for the results
of the use of this guide and the software.
・ Windows is a registered trademark of Microsoft ® Corporation in the United States
and other countries.
・ Mac is trademark of Apple Inc., registered in the U.S. and other countries.
・ The company names and product names in this guide are the trademarks or
registered trademarks of their respective companies.
・ Software may be revised and updated without prior notice.
■ Contents
Preparing for the update .................................................... 2
Update procedure sequence ........................................... 2
Computer TCP/IP setting ................................................. 4
Updating the firmware ..................................................... 6
About Failsafe Mode ....................................................... 10
Trouble shooting ............................................................ 14
SRC mode ........................................................................ 15
HY144-D-SRC Firmware Update Guide
EN
1

Advertisement

loading

Related Manuals for Yamaha HY144-D-SRC

Summary of Contents for Yamaha HY144-D-SRC

  • Page 1: Table Of Contents

    HY144-D-SRC Firmware Update Guide Thank you for choosing a Yamaha product. This guide explains how to update the HY144-D-SRC firmware. The SRC modes can be changed by updating to the card’s firmware corresponding to each SRC mode (page 7). ■ Precautions ・...

  • Page 2: Preparing For The Update

    Update each firmware component in the following sequence. • A Windows or a Mac computer To update more than one HY144-D-SRC, For the system requirements, refer to the Yamaha Pro Audio website. configure “Computer TCP/IP setting” and https://www.yamaha.com/proaudio/ perform “Updating the firmware”...

  • Page 3: Install The Dante Firmware Update Manager

    [Install this driver software anyway]. • You may be prompted to restart the computer after the installation is complete. Before proceeding to update, restart the computer. • When installing the Dante Firmware Update Manager, temporarily disable any running anti-virus software. HY144-D-SRC Firmware Update Guide...

  • Page 4: Computer Tcp/Ip Setting

    4. click or double-click [Network and Sharing 3. Click [Properties]. Center] or [View network status and tasks]. The “Local Area Connection properties” The “Network and Sharing Center” is dialog box will be displayed. displayed. HY144-D-SRC Firmware Update Guide...
  • Page 5 Properties” dialog box will be displayed. into the Mac, click [Ethernet]. 5. Click [Obtain an IP address 3. In “Configure IPv4,” choose [Using automatically]. DHCP]. 4. Click [Apply] button, then close “Network” dialog box. 6. Click [OK]. HY144-D-SRC Firmware Update Guide...

  • Page 6: Updating The Firmware

    HY144-D-SRC. Windows: Select [Start]→[All programs] NOTE or [All apps]→[Audinate]→[Dante Perform the update with the HY144-D-SRC installed in the slot of Firmware Update Manager]→[Dante a compatible device. Firmware Update Manager] , then right- 1. Connect the Dante [PRIMARY] connector click and select [Run as Administrator].
  • Page 7 Dante Firmware Update Manager. Select the [Private (underscore) (e.g., C:\temp). network] check box, and click [Allow access]. Alternatively, in the Windows firewall, click [Allow programs or functions through the Windows firewall], and if the “fum” checkbox is HY144-D-SRC Firmware Update Guide...
  • Page 8 NOTE If the update manager is blocked by the Windows firewall, If the HY144-D-SRC is not indicated, click [Refresh]. If it is the “Upgrade failed.” dialog box appears. still not indicated, check whether the cable might be...
  • Page 9 NOTE HY144-D-SRC is installed, and restart the procedure from the step 3. If update still fails, follow the instructions stated The “User Account Control” dialog box may appear. Click in “About Failsafe Mode” to perform the recovery process. [Continue] or [Yes].

  • Page 10: About Failsafe Mode

    To restore the Dante module from failsafe mode, a recovery image must be sent from the Dante Firmware Update Manager. If the red ERROR indicator of the HY144-D-SRC is lit, it may be that the Dante module is in failsafe mode.
  • Page 11 1. Turn off the power to the device to which interfaces on your computer. the HY144-D-SRC is installed. You should also disable the wireless LAN. 2. Separate the HY144-D-SRC from the Windows: Select [Start]→[All programs] Dante network. or [All apps]→[Audinate]→[Dante Firmware Update Manager]→[Dante...
  • Page 12 7. If you see the interface selection screen, select the interface card to connect the Dante device. 8. Click [Failsafe Recovery]. 9. When the HY144-D-SRC is detected, click the [Stop Scan] button. If several minutes have passed without detection, check whether the cable might be disconnected or broken, whether the TCP/IP 10.
  • Page 13 After recovery, the Dante module will be restarted. If you power-off the device to Dante Firmware Update Manager will display which the HY144-D-SRC is installed before “Processing Safe Recovery,” and then “Safe restart is completed, the data of the Dante Recovery Done.”...

  • Page 14: Trouble Shooting

    If the firewall function of anti-virus or security software is enabled, the communication may not be established properly. • Is the HY144-D-SRC to be updated is locked by Dante Device Lock? Unlock the Dante Device Lock function of the HY144-D-SRC using Dante Controller.

  • Page 15: Src Mode

    SRC mode The HY144-D-SRC has five SRC modes and they can be changed according to your sound system. Data length and number of inputs/outputs are limited by the selected SRC mode. You can confirm the SRC mode in use from Dante Controller “Device Information” or SLOT settings on the touch screen of the control surface.