Clock; Timer - Philips FW-C55/25 User Manual

CLOCK

MINI HIFI SYSTEM
PROGRAM SHUFFLE
REPEAT

TIMER

REC
NEWS T.A. AM MW FM LW
60Hz
250Hz
STANDBY
ON
CLOCK/
TIMER CD1 • 2 • 3 BAND
CD TUNER
PROG
SEARCH • TUNING STOP•CLEAR
SOUND NAVIGATION
INCREDIBLE
MIC
SURROUND
DIGITAL
SOUND CONTROL
View Clock
You can view the clock (if it is set) if the
system is in Standby mode or when any
sound source is selected (CD, TUNER, etc.).
The clock will be displayed for about seven
seconds.
• Press CLOCK/TIMER briefly.
™ "PM 10:38 or 22:38" (the
current time) will be displayed
depending on whether you have
selected 12- or 24-hour mode.
™ "--: : : : : --" will be displayed if the
clock is not set.
pg 01-26/C55-C58/34-En 23
STEREO
BACK
FRONT HSD
8KHz
500Hz 1KHz 2KHz 4KHz
DOLBY B
NR
RDS
NEWS/TA
TAPE 1 • 2 CDR/VIDEO
TAPE AUX
A. REV
PRESET
PLAY PAUSE PREV SIDE NEXT
MIC
LEVEL
DYNAMIC BASS
BOOST
Clock Setting
The clock can be set in either 12- or 24-
hour mode, e.g. "AM 12:00" or
"00:00". Before setting the clock, you
must be in the View Clock mode.
1 Press CLOCK/TIMER to select clock
mode.
2 Press PROG (on the system only) to
select 12- and 24- hour mode.
™ If 12-hour mode is selected,
"AM 12:00" starts flashing.
™ If 24-hour mode is selected,
"00:00" starts flashing.
3 Set the hour with à or á on the
system.
4 Set the minute with í or ë on the
system.
5 Press CLOCK/TIMER again to store the
setting.
™ The clock starts.
• To exit without storing the setting, press
Ç on the system.
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
– When a power interruption occurs, the
clock setting is erased.
– To set the time with RDS clock, see
"Receiving RDS Radio Station" under
TUNER section.
Timer Setting
• The system can switch on to CD,
TUNER, or TAPE 2 mode automatically
at a preset time. It can serve as an
alarm to wake you up.
• Before setting the timer, make sure the
clock is set correctly.
• The timer will always be switched on
once it is set.
• The volume of the timer will
increase from the minimum level
until the volume level before the set
is switched to standby mode.
2/22/00, 7:02 PM
TIMER
1 Press and hold CLOCK/TIMER for more
than 2 seconds to select timer mode.
™ "AM 12:00" or "00:00" or the
last timer setting starts flashing
depending on whether you have
selected 12- or 24-hour mode.
™ The
starts flashing.
TIMER
™ The selected source is lit while other
available sources are flashing.
2 Press CD, TUNER or TAPE to select the
desired source.
• Before selecting CD or TAPE, make sure
a CD or tape is loaded in the CD tray or
tape deck 2.
3 Press à or á on the system to set the
hour for the timer to start.
4 Press í or ë on the system to set the
minute for the timer to start.
5 Press CLOCK/TIMER to store the start
time.
™ The timer is now set.
™ The remains on the display.
TIMER
• At the preset time, the timer will be
activated.
™ The selected source will be played.
Notes:
– During timer setting, if no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
– If the source selected is TUNER, the last
tuned frequency will be switched on.
3139 116 19541
23