Black & Decker 7698 Instruction Manual page 5

R A B B T E N I G
Your planer can make rabbet cuts up to 5/16" (7.9mm) deep when used with the Edge and Miter Guide.
To make a rabbet cut, adjust the edge and miter guide for the desired width of cut. Make this setting along the
numbers on the bottom of the planer shoe, starting at the right hand edge of the planer blades. Set the miter
angle for 0° (perpendicular to the planer shoe). Set the cutting depth to maximum and make repeated cuts
until the desired depth is r e c a e h . d
It will be necessary to make quite a few cuts for most rabbet applications.
N O T : E
HOW TO CHANGE AND ROTATE BLADES
For best results, keep the blades clean and replace when necessary. Replacement blades are available at your
local Black & Decker service center. DO NOT ATTEMPT TO SHARPEN THESE BLADES.
e P f r r o m steps 1 through 5 on both blades in blade dr
T r u n off and unplug planer.
1. Remove the hex wrench from the hole in the base of the switch handle as.
2. Loosen (do not remove) the three scr e w . s
NOTE: There are two blades in the blade drum. Every operation you per r o
e p f r r o m on the other.
3. With the three screws loose, push the old blade out with a scr
on them so that, if this is the first time you are changing blades, you need only to turn the blade around to
expose the fresh cutting edge. Otherwise you will have to replace the blades.
4. Install the new (or reversed) blade. Slide the blade all the way in until the end of it is flush with the end of
the blade dr u m .
5. Securely tighten all three screws (for both blades) and replace the hex wr
EDGE CHAMFERING
Your planer has two precision machined grooves in the front shoe for planing along a corner of the wood. It's
a good idea to try a piece of scrap wood before doing finish work.
PLANING WIDE PIECES
The width of the planing blade is 3-1/4" (82mm). When planing a piece of wood wider than the planer
blade, a smoother finish can be attained by rounding the edges of the blade.
Rounding these edges will slightly decrease the planing width.
N O T : E
USING EDGE AND MITER GUIDE:
T r u n off and unplug planer. Return the planing depth adjustment knob to the "P" position. The edge and miter
guide is used to increase the accuracy of your planer. It is adjustable from 0 to 45°. Use it to guide the planer
on straight cuts and to make accurate bevel cuts. Its simple design allows installation and removal in seconds.
Follow the steps below to install your edge and miter guide.
1. Slide the square rod into the hole on the side of the planer near the fr
2. Loosely install the black plastic edge and miter guide lock knob in the threaded hole provided in the fr t n
of the plane.
3. Adjust the edge and miter guide to the desired planing width by aligning it with the numbers on the
bottom of the planer. NOTE: These numbers are in millimeters.
4. Tighten the edge and miter guide lock knob.
5. Adjust the bevel angle by loosening the two knobs on opposite ends of the guide and moving the
adjustable plate until the desired angle (in degrees) is obtained.
6. Tighten the two knobs on opposite ends of the guide.
USING DUST COLLECTION BAG:
T r u n off and unplug planer, Planing depth adjustment knob in "P" position. The dust collection bag gr
reduces clean-up time by collecting the dust produced by the planer. A zipper on the bottom of the bag opens
to empty the dust, and this whole bag just slips on and of . f
Follow the steps below to install your dust collection bag.
1. Install the wire frames into the plastic plate as.
2. Install the screws into the plastic plate to retain the wire frames.
3. With the zipper on the bottom (longest side of plastic plate) pull the cloth bag over the wire frame and
r t s etch the elastic band around the edge of the plastic plate and position it between the two sets of flanges on
the plate.
4. Slip the inlet opening over the shavings exhaust port on the right side of the planer.
M A N I E T N A N C E
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be
I M P O R T A N T
e p f r r o med by authorized service centers or other qualified service organizations, always using identical
replacement par . s t
W A R N N I : G
The use of any accessory not recommended for use with this tool could be hazar
S VICE INFORMATION R E
Black & Decker offers a full network of company-owned and authorized service locations throughout North
America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with
f e ficient and reliable power tool ser v c i . e
Solamente para propósito de Argentina:
Importado por: Black & Decker Argentina S.A.
Pacheco Trade Center
Colectora Este de Ruta Panamericana
Km. 32.0 El Talar de Pacheco
Partido de Tigre
Buenos Aires (B1618FBQ)
República de Argentina
Tel. (5411) 4726 4400
No. de Importador: 1146/66
Solamente para propósito de México:
Importado por: Black & Decker S.A. de C.V.
Bosques de Cidros, Acceso Radiatas No.42
3a. Sección de Bosques de las Lomas
Delegación Cuajimalpa,
05120, México, D.F.
Tel. (52) 555-326-7100
R.F.C.: BDE810626-1W7
Imported by/Importado por:
Black & Decker do Brasil Ltda.
Rod. BR 050, s/n° - Km 167
Dist. Industrial II
Uberaba – MG – Cep: 38056-580
CNPJ: 53.296.273/0001-91
Insc. Est.: 701.948.711.00-98
S.A.C.: 0800-703-4644
HECHO EN CHINA
FABRICADO NA CHINA
MADE IN CHINA
187823-00 08/22/06
u m .
f m on one blade, you will also
e w d v i r r e . The blades have two cutting edges
e c n . h
o . t n
o
a e y l t
d o u . s