Additional Safety Rules - Makita RP0910 Instruction Manual

ENGLISH
1 Collet nut
2 Wrench
3 Shaft lock
4 Tighten
5 Loosen
6 Correct size collet cone
7 Stopper pole
8 Depth pointer
9 Lock knob
10 Fast-feed button
11 Adjusting hex bolt
12 Adjusting knob
13 Stopper block
14 Nylon nut
SPECIFICATIONS
Model
Max. collet capacity ..................................................................... ø8 mm
Plunge capacity ........................................................................... 0 – 57 mm
–1
No load speed (min ) ................................................................. 27,000
Overall height .............................................................................. 260 mm
Net weight ................................................................................... 3.3 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Wear hearing protection during extended period
of operation.
3. Handle the bits very carefully.
4. Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
5. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
6. Hold the tool firmly with both hands.
7. Keep hands away from rotating parts.
8. Make sure the bit is not contacting the work-
piece before the switch is turned on.
9. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
6
Explanation of general view
15 Hex nut
16 Lock button
17 Switch trigger
18 Speed adjusting dial
19 Workpiece
20 Bit revolving direction
21 Feed direction
22 (View from the top of the
tool)
23 Correct bit feed direction
24 Lock screw
25 Guiding surface
26 Straight guide
27 Templet guide
10. Be careful of the bit rotating direction and the
11. Do not leave the tool running. Operate the tool
12. Always switch off and wait for the bit to come to
13. Do not touch the bit immediately after operation;
14. Always lead the power supply cord away from
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing router bit
ENB033-1
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Loosen the collet nut. Insert the bit all the way into the
collet cone. Press the shaft lock to keep the shaft station-
ary and use the wrench to tighten the collet nut securely.
(Fig. 1)
A 8 mm or 1/4" collet cone is factory installed on the tool.
When using router bits with other shank diameter, use
the correct size collet cone for the bit which you intended
to use. (Fig. 2)
Optional accessories include 6 mm, 8 mm and 1/4" collet
cones.
To remove the bit, follow the installation procedure in
reverse.
CAUTION:
Do not tighten the collet nut without inserting a bit, or the
collet cone will break.
28 Screw
29 Bit
30 Base
31 Templet
32 Workpiece
33 Templet guide
34 Nozzle assembly
35 Dust nozzle assembly
36 Limit mark
37 Brush holder cap
38 Screwdriver
39 Stopper pole setting nut
RP0910
feed direction.
only when hand-held.
a complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your
skin.
the tool towards the rear.
RP1110C
ø8 mm
0 – 57 mm
8,000 – 24,000
260 mm
3.4 kg