Panasonic AW-HE130WP Operating Instructions Manual page 41

Parts and their functions (continued)
Service switch settings
SW1 to SW3 (camera address setting switches)
Configure the camera address.
Set this to AUTO under normal circumstances. When cameras are set
to AUTO, addresses will be assigned to the cameras automatically
in response operation from the controller in the order in which the
cameras were connected.
To manually configure the address, set the switches as follows.
Address AUTO 1 2
SW1 OFF ON OFF
SW2 OFF ON ON
SW3 OFF ON ON
SW4 (communication format selection switch)
Selects the communication format.
When this is set to ON, standard serial communication is enabled.
When this is set to OFF, Panasonic's proprietary serial
communication is enabled.
SW5 (maintenance switch)
Fixed at OFF.
Do not change this switch setting.
SW6 (infrared output switch)
When this is set to ON, infrared output is enabled. The signal received
via the remote control sensor is output from pins 7 and 8 of the <RS-
232C IN> connector.
Signal output is disabled when this is set to OFF.
SW7 (communication baud rate switch)
When this is set to ON, the baud rate is 38400 bps.
When this is set to OFF, the baud rate is 9600 bps.
SW8 (communication connector switch)
When this is set to ON, the RS-232C is enabled.
When this is set to OFF, the RS-422 is enabled.
3 4 5 6 7
ON OFF ON OFF ON
OFF OFF ON ON OFF
ON ON OFF OFF OFF
Simultaneous output conditions for each video
„
format
z SDI/HDMI/VIDEO output
Format
HD/SDI 1080/59.94p
1080/50p
1080/59.94i
1080/50i
1080/29.97psF
1080/25psF
1080/23.98psF
1080/29.97p
1
*
1080/25p
1
*
1080/23.98p
720/59.94p
720/50p
SD/SDI 480/59.94p
576/50p
480/59.94i
576/50i
*
1
Native output
*
2
480/59.94i and 576/50i is output to the VIDEO output regardless of
the format setting.
z IP video transmission output (1-/multi-channel display)
1-channel display
Resolution
1920×1080 / 1280×720 / 640×360 / 320×180 / 160×90
(non-dependent on SYS format)
Frame 59.94Hz 1 fps/2 fps/3 fps/5 fps/6 fps/10 fps/15 fps/30 fps/
rate 60 fps
* 1
50Hz 1 fps/2 fps/5 fps/10 fps/12.5 fps/25 fps/50 fps
* 1
60 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
* 2
50 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
Multi-channel display
Setting H.264 CH1
Resolution 1920×1080
1280×720
Frame 59.94Hz 60fps
rate
50Hz
50 fps
*
3 Different resolutions must be specified for JPEG CH1 / CH2 / CH3.
SDI HDMI VIDEO
output output output
  
  
  
  
 
 
 
  
  
  
  
  


2
  *
2
  *
2
*
H.264 CH2 H.264 JPEG
CH3/CH4 CH1/CH2/
CH3
*
1920×1080 1280×720 1920×1080
1280×720 640×360 1280×720
640×360 320×180 640×360
320×180 160×90 320×180
160×90 160×90
5 fps 5 fps 1 fps
15 fps 15 fps 2 fps
30 fps 30 fps 3 fps
5 fps
6 fps
10 fps
15 fps
30 fps
5 fps 5 fps 1 fps
12.5 fps 12.5 fps 2 fps
25 fps 25 fps 5 fps
10 fps
12.5 fps
25 fps
3
41