Fujitsu F2MC-8FX Setup Manual
Starter kit (ver. 5v)
Hide thumbs
Also See for F2MC-8FX:
- Operation manual (16 pages) ,
- Hardware manual (602 pages) ,
- Application note (23 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Advertisement
Table of Contents
Related Manuals for Fujitsu F2MC-8FX
Summary of Contents for Fujitsu F2MC-8FX
- Page 1 FUJITSU SEMICONDUCTOR SS01-26008-1E SUPPORT SYSTEM MC Series MC-8FX STARTER KIT (ver. 5V) MB2146-401-03 SETUP GUIDE...
- Page 2 For mass production/evaluation MCUs for this product, consult our Sales or Support representatives. * : F MC is the abbreviation used for FUJITSU Flexible Microcontroller. Handling and use Handling and use of this product and notes regarding its safe use are described in the manuals for products bundled with the Starter Kit.
- Page 3 Indicates a potentially hazardous situation which, if not avoided appropriately, may result in minor or moderate injury and/or damage to the product or the equipment CAUTION to which the product is connected, to software resources such as data, or to other properties.
- Page 4 (i.e., submersible repeater and artificial satellite). Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products.
-
Page 5: Table Of Contents
Contents 1. Checking the Delivered Product ................1 2. Handling Precautions ..................1 3. Feature......................2 4. Hardware Setup ....................2 4.1 Configuration of each product....................3 4.2 Connection of each product ....................5 5. Software Setup....................9 5.1 Installation of software ......................9 5.2 Operation of S ...................... -
Page 6: Checking The Delivered Product
1. Checking the Delivered Product Before using the product, make sure that the following components are included: Host machine This version is limited to 45 days The inside of a dashed line is the package of this product. MC-8L/8FX Family Professional Pack OFTUNE Trial Version... -
Page 7: Feature
3. Feature The F MC-8FX starter kit is the best for a performance and functional evaluation, and a check of operation before including F MC-8FX in a user's system.By carrying out additional purchase of the header board, continuation use also of the evaluation with a user's system can be carried out. Below, the feature of the BGM debugger for F MC-8FX is shown. -
Page 8: Configuration Of Each Product
4.1 Configuration of each product This section describes how to configure the MCU Board and the Evaluation Board. Configuring MCU Board Set the following switches on the MCU Board, referring to "Figure 1 MCU Board Configuration". GNDVCC PRODUCT SELECT 1 2 3 4 1 2 3 4 ADAPTER LVD2 detection voltage selection jumper plug... - Page 9 Configuring Evaluation Board Set the following switches on the Evaluation Board, referring to "Figure 2 Evaluation Board Con- figurarion". +3.3V 5V/3.3V Power supply selector jumper plug Set the value to the side of "+5V". Analog power supply jumper plug Insert jumper plug for all the switches. MOD selector jumper plug Insert jumper plug.
-
Page 10: Connection Of Each Product
4.2 Connection of each product This section describes how to connect the MCU Board, the Evaluation Board, and the BGM Adapter. This section also describes how to mount the crystal oscillator on the MCU Board, and how to plug the AC adapter into the Evaluation Board. Connecting MCU Board and Evaluation Board Connect the MCU Board and the Evaluation Board, referring to "Figure 3 Connection of MCU Board and Evaluation Board". - Page 11 Connecting BGM Adapter Connect the BGM Adapter and the MCU Board, referring to "Figure 4 Connection of BGM Adapt- er". The BGM Adapter and the MCU Board have an index mark (for pin 1) on its connectors. Align the index mark on both sides. Plug a USB cable into the BGM Adapter (the cable is bundled with the BGM Adapter).
- Page 12 Connecting oscillators Plug crystal/ceramic oscillators into the crystal oscillator mounting sockets (one for the main clock and the other for the subclock) on the MCU Board (See "Figure 5 Connection of oscillators") . You can see one crystal oscillator mounting socket for main clock and the other for subclock on the MCU Board.
- Page 13 Connecting AC Adapter Connect the AC Adapter and the Evaluation Board, referring to "Figure 6 Connection of AC Adapt- er". The AC Adapter (bundled with the Evaluation Board) is plugged into the PJ1 on Evaluation Board and the AC 100V Power Supply. Evaluation Board BGM Adapter Plug into Evaluation Board...
-
Page 14: Software Setup
5. Software Setup In the software setup procedure, you install and operate the software applications. This chapter includes the installing and operating procedure for each software in order. Check the contents and complete the software setup. • Installation of software - Installing S OFTUNE - Installing USB driver... - Page 15 The [Install New Hardware Device Drivers] screen appears. Click [Search for a suitable driver for my device (recommended)], and then click [Next] to search for a suitable driver for your device. The [Locate Driver Files] screen appears. Check [Specify a location], and then click [Next] to specify the location for the driver. A file location dialog appears.
- Page 16 In the [Copy manufacturer’s files from] box, make sure that the "\Drivers" folder (under a directory where S is installed) is selected, and click [OK]. OFTUNE The [Driver Files Search Results] screen appears. Click [Next] to start installing the driver. The [Completing the Found New Hardware Wizard] screen appears.
- Page 17 Installing sample program Copy only a folder named "\fsg" under "\MANUAL\FirstStepGuide" in S CD into the "\sam- OFTUNE ple" folder under a directory where S is installed. OFTUNE All the data in the "\fsg" folder is set to "read-only". Open the folder’s properties, and deselect the [Read Only] checkbox, and click [OK].
-
Page 18: Operation Of Softune
5.2 Operation of OFTUNE This section describes how to start S Workbench and operate it using the sample program. OFTUNE Starting S Workbench OFTUNE Start S and configure the S development environment. From the [File] menu, click OFTUNE OFTUNE [Open Workspace]. In a file location dialog, select the "\sample\fsg\8fx_sample"... - Page 19 Select and right-click "emu_dbg.sup" under the "Debug" folder, then click [Change Settings] to start the setup wizard.
- Page 20 The setup wizard is started. Click [Next]. In [Debug Type], specify [Emulator Debugger], and click [Next]. In [ICE Type], specify [MB2146-09], and click [Next].
- Page 21 In [Device Name], specify [USB], and click [Next]. In [Output Frequency], set the frequency of oscillator connected to MCU Board, and click [Next]. The [Batch file] setting is not required. Click [Next].
- Page 22 Check [Auto-load when starting debug], and specify "fsg_sample.prc" in [After] under [Specifica- tion batch file before/after load], then click [Next]. Check [Select All], and click [Next]. Click [Finish] to complete the setup of S development environment. OFTUNE...
- Page 23 Starting Debugging <Turning Evaluation Board on> Before starting debugging, turn the Evaluation Board on. Push POWER-SW on the Board to ON (to the side of " | ") to turn it on (See "Connecting BGM Adapter" for information about POWER-SW) . After the Evaluation Board is turned on, click [Start debug] from the [Debug] menu to start debug- ging.
- Page 24 Initializing MCU Initialize MCU. To do so, click the Reset button on the task bar. Reset button...
- Page 25 Running the program You can run the program by clicking the "execution-related buttons" on the task bar. You can also set a breakpoint by clicking the " " mark in the Source window. [Execution-related buttons] [Go] [Step In] [Step Over] [Step Out] [Run Until Cursor] Source window...
- Page 26 Aborting the program After you have run the program, you can stop it by clicking the Abort button on the task bar. Abort button...
- Page 27 Ending Debugging To end debugging, click [End debug] from the [Debug] menu. <Turning Evaluation Board off> After you have finished debugging, turn the Evaluation Board off for safety. Push POWER-SW on the Board to OFF (to the side of " ") to turn it off.
- Page 28 Exiting S Workbench OFTUNE To exit S Workbench, click [Exit] from the [File] menu. OFTUNE...
- Page 29 SS01-26008-1E FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM MC Series MC-8FX STARTER KIT (ver. 5V) MB2146-401-03 SETUP GUIDE March 2005 the first edition Published FUJITSU LIMITED Electronic Devices Edited Business Promotion Dept.