Page 1
CCD MODIFICATION UNIT HKC-7080 INSTALLATION AND MAINTENANCE MANUAL 1st Edition (Revised 1)
Page 2
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
Describes the components that constitute the unit and the procedures to install the HKC-7080 in the HD color camera HDC-700. Section 2 Electrical Alignment Describes electrical adjustment necessary after the HKC-7080 is installed in the HDC-700. Section 3 Setup Menu Describes the setup menu for the modified HDC-700.
Section 1 Installation The HKC-7080 is the modification unit for the HDC-700. By installing the HKC-7080 in the HDC-700, it can be obtained for the HD signal having 1920 x 1080 effective picture elements. To install proceed as follows. 1-1. Configuration of HKC-7080 Description Q’ty...
1. Open the right and left side panels. 2. Loosen the two screws and disconnect the connector. Screws Connector Filter disk unit 3. Disconnect the flexible card wire. Refer to Section 1-3-3 before disconnecting or connecting the flexible card wire. Flexible card wire 1-2 (E) HKC-7080...
Page 11
6. Install the HKC-7080 in the reverse order of removal. . Be very careful not to touch the surface of the filter disk unit when installing the HKC-7080. . Be sure to remove the dust protection cover from the HKC-7080 previously.
1. Slide portions A in the direction of the arrow and insert the flexible card wire as far as it will go with the conductive surface down. 2. Slide portions A in the reverse direction to lock. Conductive surface 1-4 (E) HKC-7080...
1-4. Modifying Board 1-4-1. Modifying VDA-31 Board Parts Required Prepare the following resistors because they are not supplied with the unit. Description Q’ty Sony Part No. Res, metal chip 15 Z 1-218-648-11 Res, metal chip 18Z 1-218-650-11 Res, metal chip 30 Z...
1. Remove the VA-158 board. 2. Solder the jumper wires from the modification board to the positions specified by the figure. 3. Stick the modification board on the VA-158 board with Sony bond as shown in the figure. (Shaded portions) 4.
Sony Part No. 7-432-912-52 Modification Procedures 1. Remove the IF-569 board. 2. Solder the jumper wire between pin 119 of IC100 and pin 16 of IC36. 3. Stick the jumper wire with Sony bond as shown in the figure. (Shaded portion) IC100 IC36...
Modification Procedures 1. Remove the SG-226 board. 2. Solder the jumper wire between pin 119 of IC65 and pin 36 of IC71. 3. Stick the jumper wire with Sony bond as shown in the figure. (Shaded portion) IC65 TO Pin 36/IC71...
Electrical Alignment 2-1-2. Switch Setting of IF-569 Board This section explains adjustment items required after the HKC-7080 is installed. Perform the following adjustments with setup menu. 1. Turn off the power, then remove the IF-569 board. Regarding the setup menu operation, refer to Section 3.
(Select the file in accordance with the lens attached. If there is no appropriate file, select NO OFFSET, then change the name of lens with MSU.) 10uS Resetting after Adjustment . Return the switches to their previous positions. 2-2 (E) HKC-7080...
Page 19
Adjust for B-ch in the same manner. 7. Adjust the white balance. WHITE button/MSU-700 → ON (lit) Lens File Store MSU menu operation: . FILE button → ON (lit) . Touch panel operation [Lens|File] → [Lens|Store] → [Store] 2-3 (E) HKC-7080...
OHB File Store 1. MSU menu operation: . FILE button → ON (lit) . Touch panel operation [OHB|File] → [OHB|Store] → [Store] 2. When the store operation is complete, the message “OHB File Stored” is displayed. 2-4 (E) HKC-7080...
ITEM: ND OFST Store → Disable new reference file. Storing the reference file Perform the following operation with setup menu. MENU: File PAGE: Reference File ITEM: Store File (Press the MENU SELECT switch toward the ENTER to store the reference file.) 2-5 (E) HKC-7080...
Perform readjustment according as necessity, then store a new operator file. Storing the operator file Perform the following operation with setup menu. MENU: Operation PAGE: Operator File ITEM: Store (Press the MENU SELECT switch toward the ENTER to store the operator file.) 2-6 (E) HKC-7080...
RET 1 POWER H-POSI V-POSI FILTER LOCAL STORE CURSOR UP TALLY WIDTH HEIGHT B C D CENTER SAFFETY ZONE DISPLAY SCAN MARKER MARKER MENU SELECT 16:9 CALL CANCEL ENTER MENU MENU SELECT switch DISPLAY switch MENU SELECT control 3-1 (E) HKC-7080...
Page 24
In this section, an item under “Ver.” in the table shows a ROM version. If any version is given, it shows that the function for the item is added or changed, and the ROM with that version or higher version supports the function. If no version is given, it shows that every ROM version supports the function. 3-2 (E) HKC-7080...
Page 25
The lens extender is in use [On], Off Fan: Fan mode is at “Off” (forcibly off) [On], Off 60Hz 60Hz: Field frequency is set at 60 Hz [On], Off Optical Optical: “Optical” showing a photo-receptive condition indicates anything but “GRN” 3-3 (E) HKC-7080...
Page 26
Turns on and off the zebra pattern display [70], 90, 70&90 % Selects the zebra pattern [16:9], 4:3, Squeeze VF Scan Selects the VF scan mode Setting screen 16 : 9 4 : 3 Squeeze Setting screen object object object 3-4 (E) HKC-7080...
Page 27
Selects a lens file appropriate for a mounted lens from 16 kinds of the lens files Setting CCU output Connector (camera) Input level MIC1 MIC2 MIC1 LINE MIC2 LINE (Unassigned) (Unassigned) MIC2 AES/EBU Setting screen Auto-iris window frame is shown in a shaded pattern 3-5 (E) HKC-7080...
Page 28
ENTER to execute Store Throw MENU SELECT Stores the user’s operator file switch to ENTER to execute Preset Throw MENU SELECT Returns the operator file items to their preset values switch to ENTER to execute 3-6 (E) HKC-7080...
Page 29
Resets numeric settings on the Gamma page to 0 switch to ENTER to execute (When you throw MENU SELECT switch to ENTER, the “Clear” indication flashes. Throw MENU SELECT switch to ENTER again to execute; throw to CANCEL to cancel) 3-7 (E) HKC-7080...
Page 30
Resets numeric settings on the Detail 1 page to 0 switch to ENTER to execute (When you throw MENU SELECT switch to ENTER, the “Clear” indication flashes. Throw MENU SELECT switch to ENTER again to execute; throw to CANCEL to cancel) 3-8 (E) HKC-7080...
Page 31
Resets numeric settings on the Matrix page to 0 switch to ENTER to execute (When you throw MENU SELECT switch to ENTER, the “Clear” indication flashes. Throw MENU SELECT switch to ENTER again to execute; throw to CANCEL to cancel) 3-9 (E) HKC-7080...
Page 32
. Every time MENU SELECT switch is thrown to ENTER, the scene file replaces the current settings . When the scene file is recalled, an asterisk appears next to the number Standard Returns the current amount of paint adjustments and switch setting to their reference values 3-10 (E) HKC-7080...
Page 33
CANCEL to cancel) e) When executing the Auto Level, paint data is temporarily cleared and the automatic level adjustment is performed in sequence. After the adjustment is complete, adjustment result is stored as a master setup data. 3-11 (E) HKC-7080...
Page 34
Sets a camera ID of up to ten alphanumerics, symbols, and spaces If “RED” is indicated, be sure to clean the optical connector or optical connector cable. If “YEW” is indicated, cleaning them is recommended. For details on how to clean, refer to Section 2-15. 3-12 (E) HKC-7080...
Page 35
The standard values are stored at the factory ND OFST Clear Throw MENU SELECT Clears the white offset value for the ND filter switch to ENTER to execute Setting screen Auto-iris window frame is shown in a shaded pattern 3-13 (E) HKC-7080...
Page 36
Shifts vertically the location of the center marker on the screen 20 (down) ↔ _20 (up) Center POS Store Throw MENU SELECT Stores the location of the center marker at present in the switch to ENTER to execute selected lens file number 3-14 (E) HKC-7080...
Page 37
Check whether the video signals are properly output at pin 6 of IC106, IC206 and IC306 each, or not AU-203 Checks the voltage at +5 V regulated line DAP-5 Checks the audio clocks (13.5 MHz) at pin 43 of IC2 3-15 (E) HKC-7080...
Page 38
Turns on and off the function to activate the APR each time the black balance is automatically performed h) Rear tally lamp refers to back tally lamp and VF tally lamp (of HDVF-700). k) Front tally lamp refers to up tally lamp and lens tally lamp. 3-16 (E) HKC-7080...
Page 39
VF each other Left: Zoom position is located on the left and focus position is on the right Right: Zoom position is located on the right and focus position is on the left 3-17 (E) HKC-7080...
Spare Parts 4-1. Notes on Repair Parts 1. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
A-8321-193-A o MOUNTED CIRCUIT BOARD, DR-308 1-758-270-11 o FILTER UNIT, OPTICS 3-708-912-01 o LEVER, MOUNT 7-621-770-87 s SCREW +B 2.6X5 7-621-773-86 s SCREW +B 2.6X4 7-627-452-38 s SCREW,PRECISION +K 2X5 7-627-556-38 s SCREW +P 2.6X4.0 7-682-903-01 s +PWH 3X5 HKC-7080...
1-218-709-11 s METAL, CHIP 5.1K 0.50% 1/16W 1-218-717-11 s METAL, CHIP 11K 0.50% 1/16W 1-218-694-11 s METAL, CHIP 1.2K 0.50% 1/16W 1-218-699-11 s METAL, CHIP 2K 0.50% 1/16W 1-216-864-11 s METAL, CHIP 0 5% 1/16W 1-218-692-11 s METAL, CHIP 1K 0.50% 1/16W HKC-7080...
Page 44
1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V 8-729-117-16 s TRANSISTOR 2SA1611-M6 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V 8-729-120-21 s TRANSISTOR 2SD1614-T1XL 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V 8-729-143-14 s TRANSISTOR 2SC4176-B35 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V 8-729-143-07 s TRANSISTOR 2SA1610-YY33 HKC-7080...
Page 45
1-218-723-91 s METAL, CHIP 20K 0.50% 1/16W 1-218-716-11 s METAL, CHIP 10K 0.50% 1/16W 1-218-723-91 s METAL, CHIP 20K 0.50% 1/16W 1-218-716-11 s METAL, CHIP 10K 0.50% 1/16W 1-218-723-91 s METAL, CHIP 20K 0.50% 1/16W 1-218-716-11 s METAL, CHIP 10K 0.50% 1/16W HKC-7080...
Page 46
1-135-149-21 s TANTALUM, CHIP 2.2uF 10% 10V 1-135-149-21 s TANTALUM, CHIP 2.2uF 10% 10V 1-135-149-21 s TANTALUM, CHIP 2.2uF 10% 10V 1-135-149-21 s TANTALUM, CHIP 2.2uF 10% 10V 1-135-149-21 s TANTALUM, CHIP 2.2uF 10% 10V 1-135-149-21 s TANTALUM, CHIP 2.2uF 10% 10V HKC-7080...
Page 47
1-218-661-11 s METAL, CHIP 51 0.50% 1/16W 1-568-361-21 s CONNECTOR, BOARD TO BOARD 24P 1-218-661-11 s METAL, CHIP 51 0.50% 1/16W 1-218-661-11 s METAL, CHIP 51 0.50% 1/16W 1-569-607-21 o CONNECTOR, BOARD TO BOARD 24P 1-218-699-11 s METAL, CHIP 2K 0.50% 1/16W HKC-7080...
Page 48
1-218-737-11 s METAL, CHIP 75K 0.50% 1/16W R132 1-218-740-11 s METAL, CHIP 100K 0.50% 1/16W 1-218-737-11 s METAL, CHIP 75K 0.50% 1/16W R133 1-216-789-11 s METAL, CHIP 2.2 5% 1/16W 1-218-737-11 s METAL, CHIP 75K 0.50% 1/16W R134 1-216-789-11 s METAL, CHIP 2.2 5% 1/16W HKC-7080...
Page 49
1-241-833-11 s RES, ADJ, METAL 10K RV204 1-241-833-11 s RES, ADJ, METAL 10K RV301 1-241-828-21 s RES, ADJ, METAL 500 RV302 1-241-833-11 s RES, ADJ, METAL 10K RV303 1-241-833-11 s RES, ADJ, METAL 10K RV304 1-241-833-11 s RES, ADJ, METAL 10K HKC-7080...
Page 50
1-216-864-11 s METAL, CHIP 0 5% 1/16W 1-415-890-11 s DELAY LINE 8-759-173-16 s IC TL062CPW 8-759-166-02 s IC UPC814G2 8-759-195-81 s IC TC7S86FU 8-759-195-81 s IC TC7S86FU 8-759-185-42 s IC LM4040AIM3-2.5 8-759-565-12 s IC CXD9086R 8-759-271-86 s IC TC7SH04FU 8-759-196-96 s IC TC7SH08FU-TE85R 4-10 HKC-7080...
Page 59
: HIGH LEVEL : LOW LEVEL : HIGH LEVEL : DON’T CARE TC7S08FU(TE85R) (TOSHIBA) TC7SH08FU-TE85R (TOSHIBA) C-MOS 2-INPUT AND GATE —TOP VIEW— Y = A • B = A + B GND 3 0 : LOW LEVEL 1 : HIGH LEVEL HKC-7080...
Page 60
DUAL OPERATIONAL AMPLIFIERS (DUAL-SUPPLY TYPE) —TOP VIEW— X24C02S-3.0-C7000 (XICOR)(2K-BIT) X24C02S-T1 C-MOS SERIAL EEPROM —TOP VIEW— INPUT A0 - A2 : ADDRESS : SERIAL CLOCK : WRITE CONTROL INPUT/OUTPUT : SERIAL DATA NOTE : TYPE PIN 7 NM24C16 X24C02 X24C04 TEST 5-10 HKC-7080...
+3.3 V +3.3 V REF. V REG. Q7, 8 _37M OUT _5.5 V 37N/XST2 DR, 5-11 DR, 5-4 _5.5 V _5.5 V _5.5 V SLOW SCAN ON OPB PLS DR, 5-7 VL IN VL OUT DR, 5-3 TG-209 HKC-7080 HDC700A-TG209-BLOCK/M HKC-7080...
R9 51 G-PA GND R V COMP IN OPEN G V COMP IN 1.2k B V COMP IN 6.3V 0.01 R-PA OUT C301 R-PA GND IC4(3/4) 5.6k TL064CPW-E05 -5.5V 560k 0.022 2SA1611-T1M7 2SD1614-T1XL IC3(3/3) TC74HC4053AFT(EL OPEN 100k 100k IC4(4/4) TL064CPW-E05 HKC-7080...
R-PA IN G-PA OUT B-PA GND G-PA GND B-PA OUT G-PA IN VD IN CAM BLKG IN B-PA GND B-PA IN +5V OUT -5V OUT VD OUT CAM BLKG OUT DR-308 BOARD NO. 1-660-265-11 LOT NO. 808- B-¥HDC700-DR308-11 HKC-7080 7-10 7-10...
CC CONT 2 OUT CC CONT 1 OUT CC CONT 0 OUT AUX6 CN-1367 ND POSI IN BOARD NO. 1-660-262-11 ND CONT 2 OUT ND CONT 1 OUT LOT NO. 808- ND CONT 0 OUT B-¥HDC700-CN1367-11 AUX7 HKC-7080 7-11 7-11...
Page 91
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any...