Samsung ASSY MIM-H04EN Service Manual
Wi-fi kit 2.0
Hide thumbs
Also See for ASSY MIM-H04EN:
- User & installation manual (26 pages) ,
- Service manual (19 pages) ,
- User & installation manual (30 pages)
Advertisement
Table of Contents
- 1 Contents
- 2 Wi-Fi Kit Installation
- 3 Assemble the Wi-Fi Kit Again
- 4 Connecting to a Single Outdoor Unit (F1-F2)
- 5 Wi-Fi Kit Wiring Diagram
- 6 Connecting to Multiple Outdoor Units
- 7 Connecting the Wi-Fi Kit and the ERV Together (R1-R2)
- 8 Checking the Wi-Fi Kit
- 9 Initializing the User Data
- 10 Updating with the Micro SD Card
- 11 Troubleshooting
- 12 Network Environment
- 13 Wi-Fi Kit 2.0 Function
- 14 Network Error
- 15 The Connection between System AC and Wi-Fi Failed. Please Try Again.
- Download this manual
Advertisement
Table of Contents
Related Manuals for Samsung ASSY MIM-H04EN
Summary of Contents for Samsung ASSY MIM-H04EN
- Page 1 ASSY Wi-Fi Kit 2.0 Model Name : MIM-H04EN MIM-H04RN MIM-H04N MIM-H04UN MIM-H04NDZ ASSY Wi-Fi Kit 2.0 CONTENTS 1. Wi-Fi Kit 2.0 Installation 2. Troubleshooting MIM-H04EN MIM-H04RN MIM-H04N MIM-H04UN MIM-H04NDZ...
- Page 2 Contents Wi-Fi Kit 2.0 Installation ....................... 1-1 Troubleshooting ..........................2-1 Samsung Electronics...
- Page 3 2. Arrange the power and communication cables along the back cover. If necessary, remove this part to secure more space for wiring. 15 cm 10 cm 15 cm 15cm (6 inch) 10cm (4 inch) 10 cm <Installation on the wall> <Installation in the wall> Samsung Electronics...
- Page 4 50 (2 inch) mm (down) around the back cover before fixing the back cover on the wall. Item Contents Item Contents ⓐ ⓓ Power/communication terminals ⓑ ⓔ Tracking/Reset button Network PBA ⓒ ⓕ Micro SD card slot Interface module PBA Samsung Electronics...
- Page 5 1) Connecting to a single outdoor unit (F1-F2) ※ Wi-Fi Kit wiring diagram < Connection between the Wi-Fi Kit and multiple units > < Connection between the Wi-Fi Kit and a single unit > < Connecting between the Wi-Fi Kit and ERV devices > Samsung Electronics...
- Page 6 - Connect the power cables to V1 and V2 of the indoor unit. - Other controllers (e.g. touch centralized controller, DMS) can be installed together. You can connect up to 16 indoor and outdoor units ∙ CAUTION CAUTION Samsung Electronics...
- Page 7 - Connect R1 and R2 on the outdoor unit to F1 and F2 of the Wi-Fi Kit. - Connect the power cable to V1 and V2 of the the indoor unit or ERV. - Other controllers (e.g. touch centralized controller, DMS) can be installed together. Samsung Electronics...
- Page 8 Max. length for communication/power cables: 50 m (164 ft) ∙ Fasten the PCB terminal with fixing screws to a torque of 6 N•cm or less. When you fasten the screw to a torque over 6 N•cm, it may cause damage to the screw thread. Samsung Electronics...
- Page 9 For this process, refer to the 'Starting Samsung Smart Home Fi kit recognize that they are connected to the Wi-Fi kit. To monitor or control the system air conditioner with ...
- Page 10 *If you see “Rescue mode” LED when you service : - Please press “AP” button for 5 seconds. Then, Wi-Fi Kit will be do “Factory Reset” - After “Factory Reset”, please guide user to do add device through smartthings app again. Samsung Electronics...
- Page 11 6. Restarting the Wi-Fi Kit after an update failure will restore the software to the previous version. When the update failure persists, follow the instructions below: ∙ File checking: Change the update image (file). ∙ Micro SD card checking: Replace the Micro SD card. ∙ PBA checking: Replace the network PBA. Samsung Electronics...
- Page 12 ∙ The Wi-Fi Kit is not connected to the indoor unit(s) normally. ndoor unit or outdoor unit is changed, tracking should be performed again manually by pressing units by a mobile phone. For this process, refer to the 'Starting Samsung Smart Home Is the indicator blinking? Contact the Samsung service centre.
- Page 13 1. Check the connection cable between the network PBA and the Interface module PBA. The LED indicator remains in its initial state. (The LED state changes within 1 minute.) 2. Even though the connection has no problem but a problem persists, replace the Wi-Fi Kit. Samsung Electronics...
- Page 14 - More the duplication of the Wi-Fi most far-separated one channels between the router to be installed and the ones around, more the possibility of the occurrence of communication problems. [Check the frequency of channels] Start Wi-Fi Analyzer app. (Downloaded from app store) OTHERS Samsung Electronics...
- Page 15 Wi-Fi modem malfunctioning Blinking Blinking Blinking Searching AP (AP mode) OTHERS Tracking units Blinking Blinking No unit tracked Blinking Inspection of the network PBA Blinking Blinking required User authentication required Blinking (AP mode) Downloading Rescue mode Blinking Blinking Samsung Electronics...
- Page 16 - Press the tracking button for one second to performthe isdifferent from the tracking again. actualinstallation Wi-Fi kit OTHERS Item Contents Item Contents Power/communication terminals Ⓐ Ⓓ Tracking/Reset button Network PBA Ⓑ Ⓔ Micro SD card slot Interface module PBA Ⓒ Ⓕ Samsung Electronics...
- Page 17 Wi-Fi Kit 2.0 and Router. 2. Update the firmware of router with the latest - When router does not support SSDP Protocol. version. [Check the frequency of channels] Start Wi-Fi Analyzer app. (Downloaded from app store) OTHERS Samsung Electronics...
- Page 18 2. If the master indoor unit is set up, change the is designated differently in each of the indoor operating mode of master indoor unit. units). OTHERS Samsung Electronics...
- Page 19 China china.samsungcspotal.com K-Zone http://20.8.111.9 This Service Manual is property of Samsung Electronics Co., Ltd. © Samsung Electronics Co., Ltd. Jun. 2019. Any unauthorized use of Manual can be punished under applicable Printed in Korea. International and/or domestic law. Code No. AC-00246E_1...