Page Table; Initialization Of 8, C Page Data; Modification Of 8, C Page Data - Sony DCR-TRV16 Service Manual

DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-2-3.

INITIALIZATION OF 8, C PAGE DATA

Note: The data of page: 0, address: 10 must be "00".
1. Initializing the 8, C Page Data
Note1: If "Initializing the 8, C Page Data" is performed, all data
of the 8 page and C page will be initialized. (It is
impossible to initialize a single page.)
Note2: If the 8, C page data has been initialized, following adjustments
need to be performed again.

1) Modification of 8, C page data

2) Serial No. input
3) Viewfinder system adjustments
4) LCD system adjustments
5) Servo and RF system adjustments
6) Video system adjustments
Note3: The power supply voltage must be 6.0 ± 0.1Vdc.
Adjusting page
Adjusting Address
Adjusting page
Adjusting Address
Initializing Method:
Order Page Address Data
1 0 01
2 0 10
3 3 81
4 3 80
5 3 80
6
2. Modification of 8, C Page Data
If the 8, C page data has been initialized, change the data of the
"Fixed data-2" address shown in the following table by manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of 8, C Page data
Order Page Address Data
1 2 00
2 2 01
8
00 to A3
C
10 to FF
Procedure
01 Set the data.
00 Set the data.
Check that the data is "00".
0C Set the data, and press PAUSE
button.
Check that the data changes to
"1C".
Perform "Modification of 8, C
Page Data".
Procedure
29 Set the data.
29 Set the data, and press PAUSE
button.

3. 8 Page Table

Note1: The data of page: 0, address: 10 must be "00".
Note2: Fixed data-1: Initialized data. (Refer to "1. Initializing the 8, C
Page Data".)
Fixed data-2: Modified data. (Refer to "2. Modification of 8, C
Page Data").
Address Address
Initial value Initial value
00 to 18
19
1A to 28
29
2A to 2E
2F
30 to 3A
3B
3C to 49
4A
4B to 51
52
53 to 59
5A
5B to 79
7A
7B
7C
7D
7E
7F
80
81
82
83
84
85 to 89
8A
8B
8C 08
8D 00
8E 46
8F 01
90 02
91 00
92 00
93 00
94 to A3
5-12
Remark Remark
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Serial No. input
Fixed data-1
Table. 5-1-6.