Initializing The 8, A, C, D, E, F, 1F Page Data; Modification Of 8, A, C, D, E, F, 1F Page Data; Page Table - Sony CCD-TRV138 Manual

1-2. INITIALIZATION OF 8, A, C, D, E, F, 1F
PAGE DATA
Note: If reading/writing data on pages 1F, set data: 01 to page: 0,
address: 10, and then select pages F. By this data setting,
the pages 1F can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to "00".

1. Initializing the 8, A, C, D, E, F, 1F Page Data

Note 1: If "Initialization of Pages 8, A, C, D, E, F, 1F" is ex-
ecuted, all data on pages 8, A, C, D, E, F, 1F are initial-
ized. (Only an individual page cannot be initialized)
Note 2: If the 8, A, C, D, E, F, 1F page data has been initialized,
"Modification of 8, A, C, D, E, F, 1F Page Data" and all
adjustments need to be performed again.
Note 3: Check that the data of page: 0, address: 10 is "00".
Note 4: NTSC model: CCD-TRV138/TRV338
PAL model: CCD-TRV238E/TRV438E
Adjusting Page
Adjusting Address
Adjusting Page
Adjusting Address
Adjusting Page
Adjusting Address
Adjusting Page
Adjusting Address
Adjusting Page
Adjusting Address
Adjusting Page
Adjusting Address
Adjusting Page
Adjusting Address
Initializing method:
Order Page Address Data
1 0
2 7
3 7
4 7
5 7
6 2
7 2
8
CCD-TRV138/TRV238E/TRV338/TRV438E
8
00 to FF
A
10 to FF
C
10 to FF
D
10 to 7F
E
00 to FF
F
10 to FF
1F
00 to FF
Procedure
01 01
Set the following data.
03 00: NTSC model
80: PAL model
Set the following data.
00 2D: NTSC model
2F: PAL model
Set the following data, and
press PAUSE button.
01
2D: NTSC model
2F: PAL model
Check the data changes to
02
"01".
00 29
01 29 Press PAUSE button.
Perform "Modification of 8,
A, C, D, E, F, 1F Page Data"

2. Modification of 8, A, C, D, E, F, 1F Page Data

If the 8, A, C, D, E, F, 1F page data has been initialized, change
the data of the "Fixed data-2" address shown in the following table
by manual input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the
camcorder may not operate.
3) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after completing modification of 8, A, C, D, E, F, 1F
page data
Order Page Address Data
1 2 00
2 2 01
Note: If the following symptoms occur after completing of the
"Modification of 8, A, C, D, E, F, 1F Page Data", check
that the data of the "Fixed data-2" addresses of 8, A, C, D,
E, F, 1F page are same as those of the same model of the
same destination.
1) The power is shut off so that unit cannot operate.

3. 8 Page Table

Note 1: Check that the data of page: 0, address: 10 is "00".
Note 2: Fixed data-1: Initialized data. (Refer to "1. Initializing
the 8, A, C, D, E, F, 1F Page Data")
Fixed data-2: Modified data. (Refer to "2. Modification
of 8, A, C, D, E, F, 1F Page Data")
Initial value
Address
NTSC PAL
00 to FF
6-7
Procedure
29
29 Press PAUSE button.
Remark
Fixed data-1 (Initialized data)