Advertisement
Quick Links
B200G Industrial Duty Emergency Unit
Installation and Operating Instructions
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
All servicing should be performed by qualified personnel only.
Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering by
unauthorized personnel.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
Do not use this equipment for other than intended use.
Do not use outdoors.
Do not let supply cords touch hot surfaces.
Do not mount near gas or electric heaters.
Do not mount near open flames or sparks.
The battery supplied with this equipment is a sealed maintenance free lead calcium battery. Do not attempt to
service this battery.
SAVE THESE INSTRUCTIONS
CAUTION: To avoid electrical overload, total connected lamp load (factory and field installed) should not
exceed output rating.
WARNING – Shut off AC power to branch circuits to which units will be connected. All wiring should be per
N.E.C. Articles 501-4(b) and local codes.
To maintain warranty, equipment with batteries must be installed or placed on charge within prescribed period
after shipment.
(With IntelliCharge)
Philips Lighting Company
200 Franklin Square Drive
Somerset, NJ 08873
Phone: 855-486-2216
www.philips.com/luminaires
Philips Lighting Company
281 Hillmount Road
Markham ON, Canada L6C 2S3
Phone: 800-668-9008
www.philips.com/luminaires
Advertisement
Related Manuals for Philips B200G
Summary of Contents for Philips B200G
- Page 1 B200G Industrial Duty Emergency Unit (With IntelliCharge) Installation and Operating Instructions IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS All servicing should be performed by qualified personnel only.
- Page 2 Page 2 of 7 Philips Lighting Company Philips Lighting Company 200 Franklin Square Drive 281 Hillmount Road Markham ON, Canada L6C 2S3 Somerset, NJ 08873 Phone: 855-486-2216 Phone: 800-668-9008 www.philips.com/luminaires www.philips.com/luminaires...
-
Page 3: Installation Instructions
Page 3 of 7 INSTALLATION INSTRUCTIONS The B200G is intended for surface mounting only and is suitable for 120VAC or 277VAC, 60 Hz operation. 1. Remove keyway knockouts (2) if cabinet is to be mounted to the wall. 2. Remove hole plugs as needed for installing the lamp heads. (Figure 1) Figure 1 3. - Page 4 LED will be accompanied by a simultaneous beeping tone. (Note: A continuous rapid alternating Red/Green flash with rapid beeping tone indicates 277V applied to 120V input lead. TURN OFF POWER IMMEDIATELY!) Philips Lighting Company Philips Lighting Company 200 Franklin Square Drive...
- Page 5 196 hours by a short press of either the test switch or the optional IR remote control device “silence” button. Correcting fault condition will cancel fault notification. Lamp failure indication requires a manually activated diagnostic test after lamp replacement to cancel notification. Philips Lighting Company Philips Lighting Company 200 Franklin Square Drive...
- Page 6 Press any button for desired action To stop a test, press “Cancel” See label on bottom view for additional information Philips Lighting Company Philips Lighting Company 200 Franklin Square Drive 281 Hillmount Road Markham ON, Canada L6C 2S3...
- Page 7 Page 7 of 7 Figure 4 Philips Lighting Company Philips Lighting Company 9140052272 June, 2015 200 Franklin Square Drive 281 Hillmount Road Markham ON, Canada L6C 2S3 Somerset, NJ 08873 Phone: 855-486-2216 Phone: 800-668-9008 www.philips.com/luminaires www.philips.com/luminaires...