Page 1
OBJ_DOKU-20866-002.fm Page 1 Wednesday, December 7, 2016 3:23 PM Robert Bosch Power Tools GmbH 70538 Stuttgart GERMANY www.bosch-pt.com 30-19 S | 35-19 S | 40-19 S F 016 L81 143 (2016.12) O / 23 en Original instructions...
Page 2
OBJ_BUCH-1176-002.book Page 2 Wednesday, December 7, 2016 3:23 PM Robert Bosch GmbH D-70745 Leinfelden Echterdingen 0 600 xxx xxx xxx V ~ xx Hz xxx mm x A xxxx W xxxxxxxx 20xx Made in XXX AKE 40-19 S F 016 L81 143 | (7.12.16)
Page 3
OBJ_BUCH-1176-002.book Page 3 Wednesday, December 7, 2016 3:23 PM 3-4 mm Bosch Power Tools F 016 L81 143 | (7.12.16)
Page 4
OBJ_BUCH-1176-002.book Page 4 Wednesday, December 7, 2016 3:23 PM 50 mm 50 mm F 016 L81 143 | (7.12.16) Bosch Power Tools...
Page 5
OBJ_BUCH-1176-002.book Page 5 Wednesday, December 7, 2016 3:23 PM Bosch Power Tools f 016 L81 143 | (7.12.16)
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. F 016 L81 143 | (7.12.16) Bosch Power Tools...
Page 7
When cutting a limb that is under tension be alert for spring back. When the tension in the wood fibres is re- leased the spring loaded limb may strike the operator and/or throw the chain saw out of control. Bosch Power Tools F 016 L81 143 | (7.12.16)
** country specific *Accessories shown or described are not part of the standard de- livery scope of the product. A complete overview of accessories can be found in our accessories program. F 016 L81 143 | (7.12.16) Bosch Power Tools...
However if the tool is used for different (for non-EU countries 220 V, 240 V as applicable). Only use applications, with different accessories or insertion tools or is approved extension cables. Contact your Bosch Service Cen- poorly maintained, the vibration emission may differ. This tre for details.
Page 10
If the supply cable on the product is damaged, it must only be replaced by a Bosch Service Centre. – Check if all parts are seated properly and hold the chain Mounting and Tensioning the Chain bar and the chain in this position.
Therefore, the chain is automatically lubricated with 5 back (position ), so that the red dot 28 under the mark 6 chain oil during operation via the oil outlet 19. is covered. Bosch Power Tools F 016 L81 143 | (7.12.16)
– Always hold a chain saw firmly with both hands. serious injury to the operator or bystanders. – Always use a Bosch low-kickback saw chain. Keep a running chain saw clear of wire fencing or the ground. – Apply the metal gripping teeth 13 for leverage.
Page 13
The hinge-wood keeps the tree from twisting and fall- ing in the wrong direction. Do not cut through the hinge. Bosch Power Tools F 016 L81 143 | (7.12.16)
(see figure A) If the replacement of the supply cord is necessary, this has to be done by Bosch or an authorized Bosch service agent in or- Check the saw chain and chain bar according to section “Ten- der to avoid a safety hazard.
Page 15
After-sales Service and Application Have your chain sharpened professionally at your authorised Service Bosch after-sales service or sharpen it yourself with a sharp- www.bosch-garden.com ening kit suitable for the chain recommended for your chain- saw. Observe the sharpening instructions provided with the In all correspondence and spare parts orders, please always sharpening kit.
Page 16
Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally cor- rect manner. Subject to change without notice. F 016 L81 143 | (7.12.16) Bosch Power Tools...
Page 17
EU konformitási nyilatkozat Egyedüli felelőséggel kijelentjük, hogy a megnevezett termékek megfelelnek az alábbiakban felsorolásra kerülő irányelvek és rendeletek valamennyi idevágó Láncfűrész Cikkszám előírásainak és megfelelnek a következő szabványoknak. Bosch Power Tools F 016 L81 143 | (7.12.16)
Page 18
ES atitikties deklaracija Atsakingai pareiškiame, kad išvardyti gaminiai atitinka visus privalomus žemiau nurodytų direktyvų ir reglamentų reikalavimus ir šiuos standartus. Grandininis pjūklas Gaminio numeris AKE 30-19 S 3 600 H36 D.. 2006/42/EC 2014/30/EU AKE 35-19 S 3 600 H36 E..
Page 19
V. Produktkategori: 6 Bemyndiget organ: DEKRA Certification B.V., Meander 1051, 6825 MJ Arnhem, Netherlands, Nr. 0344 EU-typegodkjenningsnr. 3400653.01 CE fra bemyndiget organ nr. 2140. Teknisk dokumentasjon hos: * Bosch Power Tools F 016 L81 143 | (7.12.16)
Page 20
Призначений орган: DEKRA Certification B.V., Meander 1051, 6825 MJ Arnhem, Netherlands, Nr. 0344 Перевірка прототипу відповідно до приписів ЄС № 3400653.01 CE авторизованим іспитовим центром № 2140. Технічна документація зберігається у: * F 016 L81 143 | (7.12.16) Bosch Power Tools...
Page 21
Deklarētā pārbaudes vieta: DEKRA Certification B.V., Meander 1051, 6825 MJ Arnhem, Netherlands, Nr. 0344 EK izstrādājuma tipa pārbaude Nr. 3400653.01 CE, kas veikta reģistrētā sertifikācijas iestādē Nr. 2140. Tehniskā dokumentācija no: * Bosch Power Tools F 016 L81 143 | (7.12.16)
Page 22
* Bosch Lawn and Garden Ltd., PT-HG/ENS-PA2, Stowmarket, Suffolk IP14 1EY, England Henk Becker Helmut Heinzelmann Executive Vice President Head of Product Certification Engineering and Manufacturing Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY Stuttgart, 01.01.2017 F 016 L81 143 | (7.12.16) Bosch Power Tools...