Honeywell CentraLine LYNX BACnet CLLYUB1012S Product Data page 5

122
105
13 14 15 16 17 18 19 20 21 22 23 24
DEPTH = 57
STATUS
159 149
CLLYUB4024S
BACnet MS/TP MAC LOCAL BACnet MS/TP
ADDRESS DIP SWITCHES MOLEX CONNECTOR PINS
1 2 3 4 5 6 7 8 9 10 11 12
PANEL MOUNTING
HOLE (4 X 4.5)
Fig. 5. Panel mounting – dimensions (mm) for
CLLYUB1012S, CLLYUB4024S, and CLLYVB4024NS, only
(CLLYUB4024S and CLLYVB4024NS shown)
DEPTH = 57
139 128
NS MODELS
BACnet MS/TP MAC
ADDRESS DIP SWITCHES
1 2 3 4 5 6 7 8
DEPTH = 57
139 128
S MODELS
BACnet MS/TP MAC
ADDRESS DIP SWITCHES
1 2 3 4 5 6 7 8
Fig. 6. Panel mounting, dimensions in mm (S- and NS-
models)
NOTE: The controller is designed so that the cover does
not need to be removed from the base plate for
either mounting or wiring.
The controller mounts using four screws inserted through the
corners of the base plate. Fasten securely with four screws.
LYNX BACnet PROGRAMMABLE, VAV/UNITARY CONTROLLERS – PRODUCT DATA
122
105
13 14 15 16 17 18 19 20 21 22 23 24
DEPTH = 57
HOST
LED
159 149
CLLYVB4024NS
BACnet MS/TP MAC LOCAL BACnet MS/TP
ADDRESS DIP SWITCHES MOLEX CONNECTOR PINS
1 2 3 4 5 6 7 8 9 10 11 12
PANEL MOUNTING
HOLE (4 X 4.5)
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
HOST
STATUS
LED
LOCAL BACnet MS/TP
MOLEX CONNECTOR PINS
9 10 11 12 13 14 15 16 17 18 19 20
164
174
164
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
HOST
STATUS
LED
LOCAL BACnet MS/TP
MOLEX CONNECTOR PINS
9 10 11 12 13 14 15 16 17 18 19 20
The controller can be mounted in any orientation. Ventilation
openings are designed into the cover to allow proper heat
dissipation, regardless of the mounting orientation.
DIN Rail Mounting (S- and NS-models)
To mount the S- and NS-models onto a DIN rail, see Fig. 7
HOST
STATUS
LED
and perform the following steps:
1. Holding the controller with its top tilted in towards the DIN
rail, hook the two top tabs on the back of the controller
onto the top of the DIN rail.
2. Push down and in to snap the two bottom flex connectors
of the controller onto the DIN rail.
IMPORTANT
To remove the controller from the DIN rail, perform the
following:
1. Push straight up from bottom to release top tabs.
2. Rotate the top of the controller out towards you and
pull the controller down and away from the DIN rail to
release the bottom flex connectors.
TOP TABS
BOTTOM FLEX
CONNECTORS
Fig. 7. Controller DIN rail mounting (S- and NS-models)
Piping (AS- and NS-models)
Air Flow Pick-Up
For AS- and NS-models, connect the air flow pickup to the
two restrictor ports on the controller (see Fig. 8).
NOTE 1: Use tubing with 6 mm outside diameter and 1 mm
wall thickness.
NOTE 2: Always use a fresh cut on the end of the tubing that
connects to the air flow pickups and the restrictor
ports on the controller.
Connect the high-pressure or upstream tube to the plastic
restrictor port labeled (+), and the low-pressure or down-
stream tube to the restrictor port labeled (-). See labeling in
Fig. 8. When twin tubing is used from the pickup, split the
pickup tubing a short length to accommodate the connections.
5
DIN RAIL
EN0Z-0959GE51 R0615