Chapter 1 Error Code; User Error Code; Service Error Code - Canon Super G3 FAX Board-T1 Portable Manual

Chapter 1 Error Code

1.1 User Error Code

1.1.1 User Error Code
No.
#0001
#0003
#0005
#0009
#0012
#0018
#0037
#0059
#0995/0099 [Tx/Rx]

1.2 Service Error Code

1.2.1 Service Error Code
No.
##0100
##0101
##0102
##0103
##0104
##0106
##0107
##0109
##0111
##0114
##0200
##0201
##0220
##0232
##0237
##0261
##0280
##0281
##0282
##0283
##0284
##0285
##0286
##0287
##0288
##0289
##0290
##0670
##0671
##0672
##0673
Tx/Rx Description
[Tx] an original has jammed.
[Tx/Rx] tine-out for copying or sending/receiving a single page has occurred.
[Tx/Rx] time-out for initial identification (T0/T1) has occurred.
[Rx] recording paper has jammed or is absent.
[Tx] recording paper is absent at the other party.
[Tx/Rx] auto call initiation has failed.
[Rx] image memory overflow at time of reception has occurred.
[Tx] The number you dial and connected number (CSI) does not match.
a memory communication reservation has been cancelled.
Tx/Rx Description
[Tx] at time of transmission, the procedural signal has been transmitted more than
specified.
[Tx/Rx] the modem speed does not match that of the other party.
[Tx] at time of transmission, fall-back cannot be used.
[Rx] at time of reception, EOL cannot be detected for 5 sec (15 sec if CBT).
[Tx] at time of transmission, RTN or PIN is received.
[Rx] at time of reception, the procedural signal is received for 6 sec while in wait for the
signal.
[Rx] at time of reception, the transmitting party cannot use fall-back.
[Tx] at time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP is
received, and the procedural signal has been sent more than specified.
[Tx/Rx] memory error has occurred.
[Rx] at time of reception, RTN is transmitted.
[Rx] at time of reception, no image carrier is detected for 5 sec.
[Tx/Rx] DCN is received outside the normal parity procedure.
[Tx/Rx] system error (main program out of control) has occurred.
[Tx] encoding error has occurred.
[Rx] decoding error has occurred.
[Tx/Rx] system error has occurred.
[Tx] at time of transmission, the procedural signal has been transmitted more than
specified.
[Tx] at time of transmission, the procedural signal has been transmitted more than
specified.
[Tx] at time of transmission, the procedural signal has been transmitted more than
specified.
[Tx] at time of transmission, the procedural signal has been transmitted more than
specified.
[Tx] at time of transmission, DCN is received after transmission of TCF.
[Tx] at time of transmission, DCN is received after transmission of EOP.
[Tx] at time of transmission, DCN is received after transmission of EOM.
[Tx] at time of transmission DCN is received after transmission of MPS.
[Tx] after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has
been received.
[Tx] after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has
been received.
[Tx] after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has
been received.
[Tx] at time of V.8 late start, the V.8 ability of DIS front the receiving party is expected
to be detected, and the CI signal is expected to be transmitted in response; however,
the procedure fails to advance, and the line is released because of T1 time-out.
[Rx] at time of V.8 arrival, procedure fails to move to phase 2 after detection
signal from caller, causing T1 time-out and releasing line
[Tx] at time of V.34 transmission, a shift in procedure from phase 2 to phase 3 and
thereafter stops, causing the machine to release the line and suffer T1 timeout.
[Rx] at time of V.34 reception, a shift in procedure from phase 2 to phase 3 and thereafter
stops, causing the machine to release the line and suffer T1 timeout.
T-1-1
T-1-2
Chapter 1
of CM
0010-9404
0010-9405
1