Advertisement
Quick Links
CONVERSION INSTRUCTIONS
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE
OF IT AND KEEP IT TO HAND THROUGHOUT THE APPLIANCE'S LIFE CYCLE.
INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN
COMPLIANCE WITH THE RELEVANT REGULATIONS. THE MANUFACTURER
DECLINES ALL LIABILITY FOR IMPROPER USES OTHER THAN THOSE
STATED ABOVE.
This kit, for separate sale, has been specially designed to convert the
barbecue from LPG to NATURAL GAS.
It contains all the components and instructions necessary for the
conversion procedure.
The appliance is set in the factory to operate on LPG. The conversion
procedure (requiring the kit described below) involves replacement of all
the burner nozzles, adjustment of the primary air flow of the barbecue
section burners only, and adjustment of the minimum flame setting on the
gas taps.
On completion of these operations, replace the "regulated for gas" label on
the rear of the barbecue with the one supplied in the kit.
The installation work must be carried out by a skilled technician.
WARNING: Keep all the nozzles factory-fitted on the appliance, the union
supplied and the "regulated for gas" label. It might be necessary to convert
the appliance back from NATURAL GAS to LPG in the future.
When converting back to LPG the conversion procedure is exactly the
same as that described below for NATURAL GAS.
CONTENTS OF THE KIT
The contents of the natural gas conversion kit are listed below:
•
NATURAL GAS NOZZLES.
•
5/8" TO 1/2" GAS MALE UNION.
•
SEAL.
•
"REGULATED FOR" LABEL
Instructions for the Installer
(TO BE APPLIED AFTER CONVERSION).
9
Advertisement
Related Manuals for Smeg BQ6030
Summary of Contents for Smeg BQ6030
-
Page 1: Conversion Instructions
Instructions for the Installer CONVERSION INSTRUCTIONS THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE APPLIANCE'S LIFE CYCLE. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS. THE MANUFACTURER DECLINES ALL LIABILITY FOR IMPROPER USES OTHER THAN THOSE STATED ABOVE. - Page 2 Instructions for the Installer CONNECTION TO THE MAINS GAS SUPPLY Connect the appliance to the mains natural gas supply using a rubber or steel hose in accordance with the relevant regulations. Screw 5/8”-1/2” supplied onto the barbecue's gas inlet (C). Screw the union (A) onto the union (B) fitting the seal (D) between them, as shown.
- Page 3 Instructions for the Installer BURNER, NOZZLE AND GAS CONSUMPTION DATA TABLES Rated heat Burner capacity (kW) Left Central (BQ90T) Right Radiant grill Radiant grill (BQ90T) Ultrarapid (BQ6030T) In the by-pass n. of turns column, closed means fully screwed down. Rated heat Burner Left Central (BQ90T)
-
Page 4: Changing The Nozzles
5 Fit the rear part back into place and screw on with the fixing screws. REPLACING THE ULTRARAPID BURNER NOZZLE (BQ6030 MODELS ONLY) 1 Remove the grid, the burner cap and the flame diffuser ring. 2 Using a 7 mm socket wrench, unscrew the burner nozzle. - Page 5 Instructions for the Installer ADJUSTING THE PRIMARY AIR FLOWS The operations below must be carried out for every burner in the barbecue section: ADJUSTING THE PRIMARY AIR FLOW FOR "U"- SHAPED BURNERS 1 Undo the adjuster screw A of the air regulator sleeve.
-
Page 6: Converting From Lpg To Natural Gas
Instructions for the Installer ADJUSTING THE BURNER MINIMUM SETTING CONVERTING FROM LPG TO NATURAL GAS Perform the operations described below on all the gas taps. 1 Pull off the knob. 2 Make sure that the by-pass inside is screwed fully down.