Related Manuals for Samsung JE68-00131B
Summary of Contents for Samsung JE68-00131B
- Page 1 SRP - 770 Thermal Label Printer Operator’s Manual JE68-00131B http://www.samsungminiprinters.com Rev. 1.02...
-
Page 2: Safety Precautions
Keep the plastic bag out of children’s reach. If not, a child may put the bag on his head. This can damage the cable, which is the origin of a fire or a breakdown of the printer. PROHIBITE PROHIBITE Do not plug in or unplug with your hands If you observe a strange smoke, odor or wet. -
Page 3: Table Of Contents
...9 ⑤ Printer (SRP-770) & Repacking Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Note : Please keep the packing materials(①,②,④,⑥) for future repacking to send a printer for repairs. -
Page 4: Samsung Label Printer
Power Switch 1. Make sure that the printer’s power switch is turned off, and the power supply’s power cord is unplugged from the electrical outlet. 2. Check the label on the power supply to make sure that the voltage required by the power supply matches that of your electrical outlet. -
Page 5: Connecting The Interface Cable
4. Connecting the Interface Cable Universal Serial Bus Parallel Interface (USB) 5. Installing or Replacing the Paper Roll ① Open Cover ③ Install Roll Serial Interface RS-232 default setting is 19200 baud, no parity, 8 data bits and 1 stop bit ④... -
Page 6: Setting The Dip Switches
6. Setting The Dip Switches 6-1. Setting the Dip Switches The Dip Switches are located on the bottom of the printer. The Dip Switches are used to set the Printer to perform various functions. Follow these steps when changing Dip Switches setting : Turn the printer power switch off. -
Page 7: The Peel-Off
8. The Peel-off Printers can Peel-off a single label. You must remove the label before the printer prints the next label. Open the peel -off cover and turn on peeler switch. ① Remove the one a paper and Adjust the paper guides and close the cover. -
Page 8: Driver Install Guide
10. Driver Install Guide I. To install SRP770 windows driver 1. Insert CD-ROM included in your printer package then install guide program will appear automatically. Please click on Windows Drivers. 2. You can see the driver auto-install program prepares to install driver matching your windows system. - Page 9 5. If you want to use USB interface with SRP770 printer, please select both “SAMSUNG SRP770” and “SAMSUNG USB Port Monitor” together and click on Next>. 6. Just wait until auto-installer program finishes drivers setup. 7. Click on Finish to exit auto-installer program.
-
Page 10: To Use Usb Interface
USB interface, USB port driver should be pre-installed. Please follow next steps to properly install Samsung USB port driver in your system. . Turn off the printer power switch and don’t turn on while auto-install program setup drivers in your system. - Page 11 3) If the following message box appears while your installation, just click on 5) In Ports Tab of SRP770 Properties window, select SSUSB0: and click on Apply. Continue Anyway to continue install procedure. 4) Click on Finish to complete installation.
-
Page 12: Tip & Trouble Shooting
In Windows 98 or Me, 1) When you turn the printer power switch first time after installing USB port driver, the OS recognize the printer and pop up the window to complete USB driver installation. Just wait. 2) In Details Tab of SRP770 Properties window, select SSUSB0: 6. - Page 13 If you use Windows XP of 2000, there are two places to set the paper size in the printer properties window in comparison that there are just one place in Windows 98 or 1) First Place : General Tab – Print Preferences… - Advanced – Advanced Option window 2) Second Place : Device Setting Tab.
- Page 14 【 Specification 】 Printing method Thermal line printing Dot density 203 dpi (8 dot/mm) Printing width 25.4 ~ 101.6 mm Paper width 38.1 ~ 104 mm Printing speed 127 mm/sec Receive Buffer Size 4K Byte Note : Printing speed may be slower, depending on the data transmission speed ※...