Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Warning
About this Quick Start Guide
Cisco VG30D Voice Gateway
Quick Start Guide
First Published: May 1, 2009
Last Updated: November 9, 2010
The Cisco VG30D Voice Gateway Safety Guide must be read prior to using this
equipment and overrides as appropriate any information in respect of
connection and use of the equipment. Any enquiries regarding regulatory
aspects of this equipment should be addressed to Cisco Systems, Inc.
This Quick Start Guide enables the safe installation of your new Cisco VG30D
Voice Gateway.
It covers:
Unpacking & Inspection, page 2
•
Hardware Installation, page 3
•
Connection Sequence , page 4
•
Front Panel Indicators, page 5
•
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2009 - 2010 Cisco Systems, Inc. All rights reserved.
Advertisement
Table of Contents
Related Manuals for Cisco VG30D
Summary of Contents for Cisco VG30D
- Page 1 Quick Start Guide First Published: May 1, 2009 Last Updated: November 9, 2010 The Cisco VG30D Voice Gateway Safety Guide must be read prior to using this Warning equipment and overrides as appropriate any information in respect of connection and use of the equipment. Any enquiries regarding regulatory aspects of this equipment should be addressed to Cisco Systems, Inc.
-
Page 2: Unpacking And Inspection
Guide, which can be found as a PDF file on the enclosed CD. Before you can use your Cisco VG30D Voice Gateway, you will need to follow all the steps in this section. This will provide you with basic functionality. Find descriptions for configuration of the more advanced features of the Cisco VG30D Voice Gateway in the Cisco VG30D Voice Gateway User Guide Section 3, “Initial... -
Page 3: Hardware Installation
Store the packaging material in a clean, dry area for possible re-use. Hardware Installation The Cisco VG30D Voice Gateway must be earthed at all times through the Caution dedicated earth terminal on the rear of the unit as shown in Figure The earthing cable must conform to the following specification. -
Page 4: Connection Sequence
FUSE T2A H 250V Be sure to pay attention to cooling. Because the Cisco VG30D Voice Gateway has side-to-side cooling, the design of the rack should allow for adequate airflow on either side of the unit. Refer to the rack manufacturer’s specification for suitable mounting methods. -
Page 5: Front Panel Indicators
Step 1 Connect the mains power cable. Step 2 Install the Cisco VG30D Voice Gateway in a place that is near the mains Note power socket-outlet. Install the Cisco VG30D Voice Gateway in a place from which you can reach the mains outlet easily. -
Page 6: Back Panel Equipment
LED changes to green to indicate that the unit is functioning correctly. Back Panel Equipment Cisco VG30D Voice Gateway This section describes the back panel ports and switches that are shown in Figure Cisco VG30D Voice Gateway Quick Start Guide 78-19034-01... -
Page 7: Craft Port
The 10/100 Base-T Port gets used to connect to the IP Network to allow voice packets to be transmitted and received and for a PC that is using a Web browser to communicate with the Cisco VG30D Voice Gateway configuration and management interface. -
Page 8: Alarm Port
Back Panel Equipment Alarm Port If required, you can connect the Cisco VG30D Voice Gateway Alarm port to an alarm signal detector before powering on the unit. Switches Power On/Off Find the power On/Off switch (I / O) adjacent to the mains connector. -
Page 9: Power On Self Test And Ip Address Setup
Power On Self Test and IP Address Setup Power On Self Test and IP Address Setup On powering ON the Cisco VG30D Voice Gateway, the unit will perform a self-test. The Power LED on the front panel shows amber, and the four STATUS LEDs come on and go off (in sequence from left to right) to indicate that the unit is performing the self-test. -
Page 10: Self-Test Failure
IP network (accessible through the new IP address), or you may continue with further configuration by using the Gateway Management Interface as described in Sections 3 and 4 of the Cisco VG30D Voice Gateway User Guide. Self-Test Failure If any test in the sequence fails, the cycle of the STATUS LEDs will stop (with one LED remaining on) and the Power LED will remain AMBER. - Page 11 Warranty Terms Cisco reserves the right to refund the purchase price as its exclusive warranty remedy. To Receive a Return Materials Authorization (RMA) Number: Please contact the party from whom you purchased the product. If you purchased the product directly from Cisco, contact your Cisco Sales and Service Representative.
- Page 12 “Pocket Zip,” and “MacZip” for its own source and binary releases. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners.