1. Manuals
  2. Brands
  3. Motorola Manuals
  4. Motherboard
  5. CPV5300 CompactPCI
  6. Installation manual

Motorola CPV5300 CompactPCI Installation Manual

Single board computer and transition module
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
®
CPV5300 CompactPCI
Single Board Computer and
Transition Module
Installation Guide
CPV5300A/IH1
May 17, 1999

Advertisement

Table of Contents
loading

Related Manuals for Motorola CPV5300 CompactPCI

Summary of Contents for Motorola CPV5300 CompactPCI

  • Page 1 ® CPV5300 CompactPCI Single Board Computer and Transition Module Installation Guide CPV5300A/IH1 May 17, 1999...

  • Page 2: Summary Of Changes

    While reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc. assumes no liability resulting from any omissions in this document, or from the use of the information obtained therein. Motorola reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of Motorola to notify any person of such revision or changes.
  • Page 3 Motorola, Inc. Disclaimer of Warranty Unless otherwise provided by written agreement with Motorola, Inc., the software and the documentation are provided on an “as is” basis and without warranty. This disclaimer of warranty is in lieu of all warranties whether express, implied, or statutory, including implied warranties of merchantability or fitness for any particular purpose.
  • Page 4 The safety precautions listed below represent warnings of certain dangers of which Motorola is aware. You, as the user of the product, should follow these warnings and all other safety precautions necessary for the safe operation of the equipment in your operating environment.
  • Page 5 All Motorola PWBs (printed wiring boards) are manufactured by UL-recognized manufacturers, with a flammability rating of 94V-0. This equipment generates, uses, and can radiate electro- magnetic energy. It may cause or be susceptible to electro- magnetic interference (EMI) if not installed and used in a WARNING cabinet with adequate EMI protection.
  • Page 6 Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. Do not service or replace the lithium battery in the field. Contact your Motorola service representative to arrange for service or battery replacement. CAUTION Prière de ne pas essayer vous-même l’entretien ou le remplacement sur place de la batterie au lithium.
  • Page 7 Table of Contents Summary of Changes ....................2 CHAPTER 1 CPV5300 Single Board Computer Overview Introduction........................1-1 Additional Features ....................1-1 Input/Output Interfaces ....................1-2 Special Functions .......................1-5 Specifications ......................1-6 Additional Information Resources ................1-8 CHAPTER 2 Getting Started Antistatic Precautions ....................2-1 Before Installing the CPV5300 ..................2-2 Installing the CPV5300....................2-2 Powering up the CPV5300..................2-5 Lithium Battery ......................2-5...
  • Page 8 CHAPTER 4 Installing Options System Memory Configurations................4-1 Installing DRAM DIMMS..................4-1 Installing the CPV5300 DIMM ................4-2 Upgrading the CPU ....................4-3 Installing the On-board Disk Drives................4-3 Installation Instructions ..................4-3 Installing Ethernet Controllers................... 4-7 APPENDIX A Pin Assignments Pin Assignments for CPV5300 SBC Front Panel and CPV5300 TM Rear Panel Connectors ....................
  • Page 9 List of Figures Figure 1-1. Block Diagram of the CPV5300 Single Board Computer ......1-4 Figure 2-1. Installing the CPV5300 Single Board Computer In Your Computer Chassis ....................2-4 Figure 2-2. Front Panel Connectors and LEDs on the CPV5300 SBC......2-7 Figure 2-3. Rear Panel Connectors on the CPV5300 Transition Module....2-9 Figure 3-1.
  • Page 11 List of Tables Table 1-1. Input/Output Interfaces ................1-2 Table 1-2. Power Requirements for the CPV5300 Single Board Computer....1-6 Table 1-3. Physical Characteristics of the CPV5300 Single Board Computer ..1-6 Table 1-4. Environmental Specifications ..............1-7 Table 3-1. List of Board components for the CPV5300 Single Board Computer ..3-2 Table 3-2.
  • Page 12 Table A-15. Floppy Header Pin Assignments for the CPV5300 Single Board Computer (J11) ..................A-17 Table A-16. Floppy Header Pin Assignments for the CPV5300 Transition Module (J9) ..................A-18 Table A-17. Fan Tachometer Header Pin Assignments for the CPV5300 Transition Module (J3 and J4) ................A-20 Table A-18.

  • Page 13: Introduction

    1CPV5300 Single Board Computer Overview Introduction The CPV5300 Single Board Computer (SBC) is a CompactPCI (Compact Peripheral Communication Interface) board. It is powered by a PICMG (PCI Industrial Computer Manufacturers Group) compatible Pentium® II processor Mobile Module. The CPV5300’s 6U (160mm x 233mm x 61mm), 8HP (1.6 inch) CompactPCI standard form factor is designed for installation into PICMG CompactPCI compliant backplanes.

  • Page 14: Input/Output Interfaces

    CPV5300 Single Board Computer Overview Input/Output Interfaces Refer to Table 1-1 for brief descriptions of the input/output interfaces on the CPV5300 Note When the identical function is available through the CPV5300’s front panel and the rear transition module, you can use either the front or the rear, not both. Table 1-1.
  • Page 15 Input/Output Interfaces Table 1-1. Input/Output Interfaces (Continued) Function CPV5300 CPV5300TM80 Transition Module Front Panel On-board Rear Panel On-board EIDE interface none primary (high none 40-pin shrouded density connector) header (primary) none none none 40-pin shrouded header (secondary) Floppy interface none none none 34-pin shrouded...

  • Page 16: Figure 1-1. Block Diagram Of The Cpv5300 Single Board Computer

    CPV5300 Single Board Computer Overview Refer to Figure 1-1 for a block diagram of the CPV5300 SBC. Ethernet Ethernet SCSI Video KBD/Mouse LPT 1 COM 2 COM 1 Dual RJ45 RJ45 Mini D sub D sub D sub D sub D sub LM78 System...

  • Page 17: Special Functions

    Special Functions Special Functions The CPV5300 uses these functions designed for use in certain applications: Watchdog Timer The watchdog timer can operate in four modes: – Disabled – Set a flag in a register in ISA I/O memory map – Set a flag in a register in ISA I/O memory map + Assert a selectable interrupt (ISA, NMI, SMI, SCI) –...

  • Page 18: Specifications

    CPV5300 Single Board Computer Overview Specifications Refer to Table 1-2 for input current specifications and to Table 1-3 for physical characteristics for the CPV5300 Single Board Computer. Table 1-2. Power Requirements for the CPV5300 Single Board Computer Input power Clock speed +5V @ 3A 266MHz w/64 or 128MB SDRAM 333MHz w/64 or 128MB SDRAM...
  • Page 19 Specifications Refer to Table 1-4 for environmental specifications Table 1-4. Environmental Specifications Parameter Condition Specification Temperature Operating 0°C to 55°C (32°F to 130°F) Non-operating -40°C to 65°C (°-40F to 150°F) Humidity Operating 5% to 90% @ 40°C, non-condensing Non-operating 5% to 95% @40°C, non-condensing Shock Operating 10G, 3 axis...

  • Page 20: Additional Information Resources

    CPV5300 Single Board Computer Overview Additional Information Resources For additional information, go to this Web site: Motorola Computer Group: http://www.mcg.mot.com...

  • Page 21: Antistatic Precautions

    Antistatic Precautions Take care when handling the CPV5300. The CPV5300 and its active components are sensitive to electrostatic discharge (ESD), and can easily be damaged. Motorola recommends Caution that you use an antistatic wrist strap when handling the CPV5300 and associated components. Also, follow these...

  • Page 22: Before Installing The Cpv5300

    Getting Started Before Installing the CPV5300 After removing the CPV5300 from its packaging: Check for obvious physical damage. Verify that the coin cell battery is in its holder and inserted correctly. Install main memory DIMMs. Refer to Chapter 4, “Installing Options”...
  • Page 23 Installing the CPV5300 7. Simultaneously move the injector/ejector levers in an inward direction. 8. Verify that the CPV5300 is properly seated and secure it to the chassis using the two screws located adjacent to the injector/ ejector levers. 9. Connect the appropriate cables to the CPV5300.

  • Page 24: Figure 2-1. Installing The Cpv5300 Single Board Computer In Your Computer Chassis

    Getting Started 10. Repeat steps 3 through 8 for installing the transition module. Transition Module Single Board Computer 2165 9803 Figure 2-1. Installing the CPV5300 Single Board Computer In Your Computer Chassis...

  • Page 25: Powering Up The Cpv5300

    The CMOS backup battery for the real time clock is socketed. The battery rates at 280mA/hour and has a ten year expected shelf life. Do not service or replace the lithium battery in the field. Contact your Motorola service representative to arrange for service or battery replacement. Caution...

  • Page 26: Front Panel Connectors On The Cpv5300

    Getting Started Front Panel Connectors on the CPV5300 The CPV5300’s front panel has connectors for: keyboard/mouse SCSI video parallel printer COM1 and COM2 (serial ports) Ethernet 1 and Ethernet 2 USB1 and USB2 LED Indicator lights on the front panel display of the CPV5300 include: watchdog alarm speaker status hard disk drive activity...

  • Page 27: Figure 2-2. Front Panel Connectors And Leds On The Cpv5300 Sbc

    Front Panel Connectors on the CPV5300 Refer to Figure 2-2 for front panel connectors and LEDs on the CPV5300. RESET Indicator Lights RESET Video ALRM SPKR Parallel Port COM 1 Keyboard/Mouse COM 2 Ethernet 1 CPV5300 Ethernet 2 Floppy SCSI Drive 2425 9812 Figure 2-2.
  • Page 28 Getting Started Rear Panel Connectors on the CPV5300 Transition Module The CPV5300 Transition Module has connectors on the rear panel for: keyboard/mouse Ethernet 1 and Ethernet 2 COM1 and COM2 (serial ports) parallel printer video SCSI...

  • Page 29: Rear Panel Connectors On The Cpv5300 Transition Module

    Rear Panel Connectors on the CPV5300 Transition Module Refer to Figure 2-3 for rear panel connectors on the CPV5300 Transition Module. Keyboard Mouse Ethernet 1 COM 2 Ethernet 2 COM 1 Parallel Port Video SCSI CPV5300TM 2426 9812 Figure 2-3. Rear Panel Connectors on the CPV5300 Transition Module...
  • Page 30 Getting Started 2-10...

  • Page 31: Components For The Cpv5300 Single Board Computer

    3Components on the CPV5300 Components for the CPV5300 Single Board Computer The CPV5300 Single Board Computer (SBC) carries components on both sides. Figure 3-1 shows the location of the jumpers and headers. ISO Bridge DIMM Socket PCI/PCI Bridge Mobile Module Ethernet Controllers Battery ISA Bridge...
  • Page 32 Components on the CPV5300 Table 3-1 lists the connectors available to support devices on the CPV5300. Refer to Appendix A for connector pin assignments. Table 3-1. List of Board components for the CPV5300 Single Board Computer Figure 3-1 Description callout CPCI backplane connector CPCI backplane connector I/O Transition Module backplane...

  • Page 33: Components For The Cpv5300 Transition Module

    Components for the CPV5300 Transition Module Components for the CPV5300 Transition Module Figure 3-2 shows major components on the CPV5300 Transition Module (TM) board.

  • Page 34: Figure 3-2. Location Of Major Components On The Cpv5300 Tm

    Components on the CPV5300 2451 9812 Figure 3-2. Location of Major Components on the CPV5300 TM...
  • Page 35 Components for the CPV5300 Transition Module Table 3-2 lists components on the CPV5300 Transition Module Table 3-2. List of Board Components for the CPV5300 Transition Module Figure 3-2 Description callout reserved for future alarm expansion reserved for future alarm expansion Fan Tach Fan Tach EIDE Channel (secondary)

  • Page 36: Connecting To And Configuring Headers

    Components on the CPV5300 Connecting to and Configuring Headers The CPV5300 provides several headers for attaching peripheral devices. Before installing the CPV5300, you may want to connect your peripheral cables to the headers. Headers are circuit board mounted components, as opposed to connectors which are located on the CPV5300’s front panel and the CPV5300 Transition Module’s rear panel.

  • Page 37: System Memory Configurations

    4Installing Options System Memory Configurations The CPV5300 has two 168-pin DIMM sites for memory expansion, organized as two memory banks (Bank 0 and Bank 1). Each bank consists of one socket providing a 64-bit wide data path and eight ECC bits. The DIMM sites accept industry standard PC100 compliant DIMM modules (8, 16, 32, 64, 128 or 256Mb) with or without ECC.

  • Page 38: Installing The Cpv5300 Dimm

    Installing Options Installing the CPV5300 DIMM You do not need tools for this procedure. 1. Remove power from the chassis and disconnect all power cords. 2. Remove the CPV5300 from the chassis. 3. Locate the DIMM sockets on the CPV5300. Refer to Figure 3-1. 4.

  • Page 39: Upgrading The Cpu

    Upgrading the CPU Upgrading the CPU If you need to remove/replace your CPU contact your field sales representative. Do not try to remove/replace your system CPU. The EMC2 socket on the board is delicate and could be damaged during removal and replacement. Caution Installing the On-board Disk Drives The CPV5300 has an optional, on-board EIDE drive and a floppy drive.

  • Page 40: Figure 4-2. Eide (J9) And Floppy Drive (J11) Headers On The Cpv5300

    Installing Options 3. Locate the EIDE (J9) and Floppy (J11) drive headers on the CPV5300. Refer to Figure 4-2. Floppy Drive Header ISO Bridge DIMM Socket PCI/PCI Bridge Mobile Module Ethernet Controllers Battery ISA Bridge AGP controller SCSI Flash Bios EIDE Header 2452 9812 Figure 4-2.
  • Page 41 Installing the On-board Disk Drives 4. If installing a floppy drive, attach one end of the cable to its connector on the CPV5300. To attach the cable, push up on each end of the plastic connector. The connector releases so that the cable can be inserted in the connector.
  • Page 42 Installing Options 7. Attach the drive carrier to the CPV5300 using two screws. 2173 9803...

  • Page 43: Installing Ethernet Controllers

    Installing Ethernet Controllers 8. Attach the remaining end of the floppy cable. Push up on the tabs on the connector and insert the floppy cable. Push down on the tabs to secure the cable. 2171 9803 9. Install the CPV5300 in the chassis and connect the power cords. Installing Ethernet Controllers The CPV5300 has two on-card Ethernet controllers called: Ethernet 1 (LAN 1)
  • Page 44 Installing Options Depending on the method the operating system uses to detect on-card devices, Ethernet 1 may not correspond to the first Ethernet controller reported by the system. If Ethernet connection is critical, we recommend installing and testing only one Ethernet connection at a time to determine the operating system to hardware binding for the Caution LAN controllers.
  • Page 45 APin Assignments Refer to Table A-1 to locate pin assignment information in this appendix. Table A-1. Pin Assignment Locator Table For pin assignments for the: Go to page: • CPV5300 Single Board Computer (SBC) front panel connectors • CPV5300 Transition Module (TM) rear panel connectors •...

  • Page 46: Pin Assignments For Cpv5300 Sbc Front Panel And Cpv5300 Tm Rear Panel Connectors

    Pin Assignments for CPV5300 SBC Front Panel and CPV5300 TM Rear Panel Connectors Pin Assignments for CPV5300 SBC Front Panel and CPV5300 TM Rear Panel Connectors This section gives you pin assignment information for CPV5300 Single Board Computer front panel connectors and CPV5300 Transition Module (TM) rear panel connectors.

  • Page 47: Keyboard/Mouse Ps2 Connectors

    Pin Assignments Keyboard/Mouse PS2 Connectors Refer to Table A-3, Table A-4, and Table A-5 for pin assignments for the CPV5300 and CPV5300 Transition Module (TM) keyboard and mouse connectors. CPV5300 Keyboard/Mouse • CPV5300 keyboard/mouse PS2 connector (J14) Table A-3. Keyboard/Mouse P/S2 Connector Pin Assignments for the CPV5300 Single Board Computer Signal Signal Description...

  • Page 48: Cpv5300 Transition Module Keyboard/Mouse

    Pin Assignments for CPV5300 SBC Front Panel and CPV5300 TM Rear Panel Connectors CPV5300 Transition Module Keyboard/Mouse • CPV5300 Transition Module (TM) keyboard P/S2 connector Table A-4. Keyboard P/S2 Connector Pin Assignments for the CPV5300 Transition Module (TM) Signal Signal Description Number Mnemonic KBDDAT...

  • Page 49: Ethernet Connectors

    Pin Assignments Ethernet Connectors Refer to Table A-6 for pin assignments for the: • CPV5300 – Ethernet 1 (J13) – Ethernet 2 (J6) • CPV5300TM – Ethernet 1 (J13) – Ethernet 2 (J18) Table A-6. Ethernet Connector Pin Assignments for the CPV5300 Single Board Computer and CPV5300 Transition Module Signal Signal Description...

  • Page 50: Parallel Connector

    Pin Assignments for CPV5300 SBC Front Panel and CPV5300 TM Rear Panel Connectors Parallel Connector Refer to Table A-7 for pin assignments for the: • CPV5300 parallel port • CPV5300TM parallel port Table A-7. Parallel Connector Pin Assignments for the CPV5300 Single Board Computer and CPV5300 Transition Module Signal Signal Description...
  • Page 51 Pin Assignments Table A-7. Parallel Connector Pin Assignments for the CPV5300 Single Board Computer and CPV5300 Transition Module (Continued) Signal Signal Description Number Mnemonic Ground Ground Ground Ground...

  • Page 52: Serial Port Connector

    Pin Assignments for CPV5300 SBC Front Panel and CPV5300 TM Rear Panel Connectors Serial Port Connector Refer to Table A-8 for pin assignments for the: • CPV5300 – COM 1 (Serial Port 1) (J15) – COM 2 (Serial Port 2) (J8) •...

  • Page 53: Universal Serial Bus (Usb) Connectors

    Pin Assignments Universal Serial Bus (USB) Connectors Refer to Table A-9 for pin assignments for the: • CPV5300 Port 1 and Port 2 (J3) • CPV5300TM Port 1 and Port 2 (J12) Table A-9. USB Connector Pin Assignments for the CPV5300 Single Board Computer and CPV5300 Transition Module Signal Signal Description...

  • Page 54: Video Connector

    Pin Assignments for CPV5300 SBC Front Panel and CPV5300 TM Rear Panel Connectors Video Connector Refer to Table A-10 for pin assignments for the: • CPV5300 (J15) • CPV5300TM (J16) Table A-10. Video Connector Pin Assignments for the CPV5300 Single Board Computer and CPV5300 Transition Module Signal Signal Description...

  • Page 55: Scsi Connector

    Pin Assignments SCSI Connector Refer to Table A-11 for pin assignments for the: • CPV5300 SCSI connector (J7) • CPV5300 Transition Module (TM) SCSI connector (J17) Table A-11. SCSI Connector Pin Assignments for the CPV5300 Single Board Computer and CPV5300 Transition Module Signal Signal Signal...
  • Page 56 Pin Assignments for CPV5300 SBC Front Panel and CPV5300 TM Rear Panel Connectors Table A-11. SCSI Connector Pin Assignments for the CPV5300 Single Board Computer and CPV5300 Transition Module (Continued) Signal Signal Signal Signal Description Number Mnemonic Description Number Mnemonic Ground ATN- Driven as an initiator...

  • Page 57: Pin Assignments For Cpv5300 Sbc And Cpv5300 Tm Headers And Jumpers

    Pin Assignments Pin Assignments for CPV5300 SBC and CPV5300 TM Headers and Jumpers This section gives you pinout information for CPV5300 Single Board Computer and CPV5300 Transition Module (TM) headers and jumpers. Refer to Table A-12. Table A-12. On Board Headers on the CPV5300 Single Board Computer and CPV5300 Transition Module Connector Type...

  • Page 58: Eide Headers

    Pin Assignments for CPV5300 SBC and CPV5300 TM Headers and Jumpers EIDE Headers Refer to Table A-13 and Table A-14 for EIDE header pin assignments for the: • CPV5300 Single Board Computer (SBC) (J9) • CPV5300 Transition Module (TM), primary - (J8), secondary - (J5) Table A-13.
  • Page 59 Pin Assignments Table A-13. EIDE Header Pin Assignments for the CPV5300 Single Board Computer (J9) (Continued) Signal Signal Signal Signal Number Mnemonic Description Number Mnemonic Description drive interrupt request drive register and data port address lines drive register drive register and data port and data port address lines...
  • Page 60 Pin Assignments for CPV5300 SBC and CPV5300 TM Headers and Jumpers Table A-14. EIDE Header Pin Assignments for the CPV5300 Transition Module (Primary - J8), (Secondary - J5) (Continued) Signal Signal Signal Signal Number Mnemonic Description Number Mnemonic Description drive data line DD14 drive data line drive data line...

  • Page 61: Floppy Headers

    Pin Assignments Floppy Headers Refer to Table A-15 and Table A-16 for floppy header pin assignments for the: • CPV5300 Single Board Computer (SBC), (J11) • CPV5300 Transition Module (TM), (J9) Table A-15. Floppy Header Pin Assignments for the CPV5300 Single board Computer (J11) Signal Signal...
  • Page 62 Pin Assignments for CPV5300 SBC and CPV5300 TM Headers and Jumpers Table A-15. Floppy Header Pin Assignments for the CPV5300 Single board Computer (J11) (Continued) Signal Signal Signal Signal Description Number Mnemonic Description Number Mnemonic MTR0 motor enable drive common outputs RDATA raw read data from disk...
  • Page 63 Pin Assignments Table A-16. Floppy Header Pin Assignments for the CPV5300 Transition Module (J9) (Continued) Signal Signal Signal Signal Description Number Mnemonic Description Number Mnemonic drive common controls direction of the floppy disk drive head during seek operation drive common STEP supplies step pulses to move head during seek...

  • Page 64: Fan Tachometer Headers

    Pin Assignments for CPV5300 SBC and CPV5300 TM Headers and Jumpers Fan Tachometer Headers Refer to Table A-17 for tachometer header pin assignments for the CPV5300 Transition Module (TM), (J3 and J4). Table A-17. Fan Tachometer Header Pin Assignments for the CPV5300 Transition Module (J3 and J4) Signal Signal...
  • Page 65 Pin Assignments Table A-18. SM Bus and LM78 Header Pin Assignments for the CPV5300 Transition Module (Continued) Signal Signal Signal Signal Description Number Mnemonic Description Number Mnemonic ground SMBDATA SM bus data strobe signal SM bus power SMBCLK SM bus clock signal BYPASS power switch SM bus power...

  • Page 66: Pin Assignments For Cpv5300 Sbc And Cpv5300 Tm Backplane Connectors

    Pin Assignments for CPV5300 SBC and CPV5300 TM Backplane Connectors Pin Assignments for CPV5300 SBC and CPV5300 TM Backplane Connectors This section gives you pinout information for: • CPV5300 Single Board Computer backplane connectors (J4, J5) • CPV5300Transition Module backplane connectors (P4, P5) A-22...

  • Page 67: J4 And P4 Connectors

    Pin Assignments J4 and P4 Connectors Refer to Table A-19 for connector pin assignments and Table A-20 for signal descriptions for the: • CPV5300 Single Board Computer (SBC), (J4) • CPV5300 Transition Module (TM), (P4) Table A-19. CPV5300 SBC (J4)/CPV5300 TM (P4) Backplane Connector Pin Assignments Number LANB RD-...
  • Page 68 Pin Assignments for CPV5300 SBC and CPV5300 TM Backplane Connectors Table A-19. CPV5300 SBC (J4)/CPV5300 TM (P4) Backplane Connector Pin Assignments (Continued) Number ATN- BSY- SACK- SRST- MSG- SEL- SREQ- SCD8 SCD9 SCD10 SCD11 PBYPASS FAN3 FAN2 INTRUDER- SSDA SSCL A-24...
  • Page 69 Pin Assignments Table A-20. Signal Descriptions for CPV5300 SBC (J4)/CPV5300 TM (P4) Backplane Connector Pin Assignments Signal Signal Signal Description Mnemonic Ethernet RD+, RD- differential receive lines TD+, TD- differential transmit lines LED1_2 transmit LED LED3 link LED General 5 volt power ground plane EIDE IOCS16...
  • Page 70 Pin Assignments for CPV5300 SBC and CPV5300 TM Backplane Connectors Table A-20. Signal Descriptions for CPV5300 SBC (J4)/CPV5300 TM (P4) Backplane Connector Pin Assignments (Continued) Signal Signal Signal Description Mnemonic SCSI driven as an initiator when a special condition occurs driven by initiator as a hand-shake during arbitration indicates command or message phase when asserted, data phase when deasserted...

  • Page 71: J5 And P5 Connectors

    Pin Assignments J5 and P5 Connectors Refer to Table A-21 for connector pin assignments and Table A-22 for signal descriptions for the: • CPV5300 Single Board Computer (SBC), (J5) • CPV5300 Transition Module (TM), (P5) Table A-21. CPV5300 (J5)/CPV5300 TM (P5) Backplane Connector Pin Assignments Number SPKR...
  • Page 72 Pin Assignments for CPV5300 SBC and CPV5300 TM Backplane Connectors Table A-22. Signal Descriptions for CPV5300 SBC (J5)/CPV5300 TM (P5) Backplane Connector Pin Assignments Signal Signal Signal Description Mnemonic General 5V power supply digital signal ground plane Miscellaneous SPKR PC/AT speaker output, open collector DIAG diagnostic/alarm output, open collector PBRESET...
  • Page 73 Pin Assignments Table A-22. Signal Descriptions for CPV5300 SBC (J5)/CPV5300 TM (P5) Backplane Connector Pin Assignments (Continued) Signal Signal Signal Description Mnemonic ring indicator request to send serial receive data serial transmit data Floppy Disk Drive, DSKCHG indicates the drive door has been opened TTL levels controls direction of the head during step operations DRVDENS...
  • Page 74 Pin Assignments for CPV5300 SBC and CPV5300 TM Backplane Connectors Table A-22. Signal Descriptions for CPV5300 SBC (J5)/CPV5300 TM (P5) Backplane Connector Pin Assignments (Continued) Signal Signal Signal Description Mnemonic chip select drive 1, also command register block select DA[2:0] drive register and data port address lines INTRQ drive interrupt request...
  • Page 75 Index functions advanced system monitoring additional information watchdog timer altitude antistatic precautions getting started block diagram CPV5300 humidity components information CPV5300 input/output interfaces CPV5300TM installing ethernet controllers configurations installing options connecting to headers installing the CPV5300 interfaces upgrading COM1 (serial port 1) CPU speed settings COM2 (serial port 2) EIDE...
  • Page 76 Index memory configurations Motorola Computer Group MTBF options overview physical characteristics pin assignments power requirements powering up rear panel connectors shock special functions specifications speed settings system memory configurations temperature upgrading the CPU vibration web sites wet bulb IN-2 Computer Group Literature Center Web Site...
  • Page 77 ® CPV5300 CompactPCI Cover Single Board Computer and Transition Module Installation Guide 34 pages ® ™ 1/8” spine 36 - 84 pages ® ™ 3/16” & 1/4” spine 86 - 100 pages ® ™ 5/16” spine 102 - 180 pages ®...

This manual is also suitable for:

Cpv5300tm80

Table of Contents