Motorola GP68 Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Motorola Manuals
  4. Motherboard
  5. GP68
  6. Installation and operation manual
Motorola GP68 Installation And Operation Manual

Motorola GP68 Installation And Operation Manual

Smartrunk ii logic board
Hide thumbs Also See for GP68:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Operating Manual
Manual Number: 502-4501
Installation and Operation
Manual
SmarTrunk II
TM
Logic Board
for
Motorola GP68
Portable Radios
SmarTrunk Systems, Inc. • ST-865M3
Motorola P/N PMLN4066A
23278 Bernhardt Street • Hayward, CA. 94545
Phone: (510) 887-1950 • Fax: (510) 887-4011
Internet: admin@smartrunk.com

Advertisement

Table of Contents
loading

Related Manuals for Motorola GP68

Summary of Contents for Motorola GP68

  • Page 1 Manual Number: 502-4501 Installation and Operation Manual SmarTrunk II Logic Board Motorola GP68 Portable Radios SmarTrunk Systems, Inc. • ST-865M3 Motorola P/N PMLN4066A 23278 Bernhardt Street • Hayward, CA. 94545 Phone: (510) 887-1950 • Fax: (510) 887-4011 Internet: admin@smartrunk.com...
  • Page 2 SmarTrunk’s product quality and customer service. SmarTrunk is a Trademark of SmarTrunk Systems, Inc. Motorola Manual Number 68P04370J43 Warranty Policy SmarTrunk Systems, Inc. ATTN: Repair Department 23278 Bernhardt Street Hayward, CA 94545, U.S.A.
  • Page 3 1.3.1 Subscriber To Landline Call ... 3 1.3.2 Subscriber To Subscriber Call ... 3 1.3.3 Fleet Dispatch (Subscriber) To Group Call ... 3 1.3.4 Conventional Mode ... 3 1.3.5 Mobile Operator Call ... 4 1.3.6 Emergency Call ... 4 1.4.1 Store And Send Dialing ...

  • Page 4: Table Of Contents

    Model ST-865M3 SmarTrunk II™ Logic Board 3.3.1 Replace Radio Chassis ... 19 3.3.2 Replace Battery and Antenna ... 20 3.5.1 System Tone ... 22 4.2.1 Number of Trunking Channels ... 24 4.2.2 Primary Code ... 26 4.2.3 Secondary Code ... 26 4.2.4 Priority Subscriber Enable ...
  • Page 5 Figure 3-5 • Replace Radio's Chassis ... 19 Figure 3-6 • Troubleshooting ... 21 Appendix A • Programming Worksheet ... 33 Appendix B • Motorola P/N • HLN9247A & HLN3083A SmarTrunk Systems, Inc. • ST-868M50 Cross Reference Chart ... 35...
  • Page 6 Model ST-865M3 SmarTrunk II™ Logic Board (This page left blank intentionally)

  • Page 7: Conventional Mode

    ST-865M3 SmarTrunk II Logic Board is a microprocessor based radio trunking logic board designed for use with Motorola GP68 Radio. The ST-865M3 implements SmarTrunk II, an efficient radio channel allocation proto- col. The SmarTrunk II Logic Board controls all radio functions including channel scan, PTT, and all transmit and receive audio.
  • Page 8 Model ST-865M3 SmarTrunk II™ Logic Board (This page left blank intentionally) viii...
  • Page 9 ubscribers already familiar with the original SmarTrunk system will find the SmarTrunk II digital system just as easy to use. There are also many additional features and enhancements. The ST-865M3 begins trunking operation as soon as the radio is powered on. Channel selection, transmit control, receiver audio, and other radio functions are all under the control of the ST-865M3.
  • Page 10 Model ST-865M3 SmarTrunk II™ Logic Board The subscriber is alerted to an incoming call by ringing of the subscriber equipment. This alerting takes four forms, related to the type of incoming call. A long single high frequency ring is generated by the logic board, then a low frequency dual tone ring is generated by the controller.
  • Page 11 Subscriber to Landline 1 Subscriber to Landline 2 Subscriber to Subscriber Fleet-Dispatch/Group Call Conventional Mode Mobile Operator Emergency Routing codes 1 and 2 give the subscriber access to tele- phone line one or two respectively. A subscriber may be restricted from line 2, or there may not be two telephone lines connected to the ST-852M.
  • Page 12 Model ST-865M3 SmarTrunk II™ Logic Board Routing code 9 calls the subscriber that is preprogrammed as the Mobile Operator. This functions as though the sub- scriber had used routing code 3 with the subscriber ID num- ber of the Mobile Operator. The Mobile Operator is pro- grammed by the System Operator/Manager.

  • Page 13: Store And Send Dialing

    Table 1-2 and the following paragraphs summarize the advanced dialing modes available: Store and Send Dialing Memory Speed Dialing Programming Speed Dial Memory (The ability to program speed dial numbers can be disabled by the dealer). Redial Mode Priority Call Overide This is the normal method of placing a telephone call.
  • Page 14 Model ST-865M3 SmarTrunk II™ Logic Board This procedure is used for dialing a telephone number or subscriber ID number that is stored in the speed dial memory: Example: The following procedure is used for programming a tele- phone number or subscriber ID number into the ST-865M3 speed dial memory.

  • Page 15: Redial

    Redial is most often used after a telephone number is dialed using the store and send method and the line is busy or a trunking channel is not available. Example: To redial the last number dialed: Press the Turning off the power to the radio clears the redial memory. If redial is attempted when no number has been entered, a low frequency error tone will be heard.

  • Page 16: Clear Channel Alerting

    Model ST-865M3 SmarTrunk II™ Logic Board If a call is attempted and no trunking channels are available, the subscriber will get a busy signal. The subscriber can try to redial over and over until the call is processed but this is very frustrating.
  • Page 17 1 • Operation If the radio has been remotely disabled by the System Operator/Manager, it will generate a continuous stream of low frequency beeps and will not operate. The radio must be returned to the dealer or System Operator/ Manager for reprogramming. Radio-Kill is a feature that is programmed and managed by the System Operator/Manager.
  • Page 18 Model ST-865M3 SmarTrunk II™ Logic Board (This page left blank intentionally)
  • Page 19 he ST-865M3 may be operated in three modes; Radiotelephone, Fleet Dis- patch and Conventional. The System Operator/Manager determines which of these modes are made available to each subscriber. The features of the operating modes are described below: • Radiotelephone - The subscriber receives private calls and group calls. He can initiate telephone calls, call other radiotelephone subscribers and call any group.
  • Page 20 Model ST-865M3 SmarTrunk II The System Operator/Manager activates a subscriber (individual or group) by programming the ST-852M SmarTrunk II Controller. This activation involves assigning a Subscriber ID Number, Paging Code Number, operational type and a number of other controller parameters. As previously stated, each piece of SmarTrunk II subscriber equipment is capable of "over the air"...
  • Page 21 Example #3: Table 2-1 illustrates a possible programming/activation scenario. The first three subscribers are individual subscribers using half duplex type equipment. These paging codes will be programmed into only one piece of subscriber equipment in the Primary Code position. The fourth and fifth entries are group subscribers. The group paging code may be programmed into many pieces of subscriber equipment as Primary Code or Secondary Code (Group/Sub-Group).

  • Page 22: Primary Code

    Model ST-865M3 SmarTrunk II Primary Code Secondary Code If the Conventional Mode feature is enabled, the subscriber may switch to Conventional Mode operation by pressing the 5 key then pressing the (*) key on the keypad (PTT not pressed). The subscriber may then set the channel select switch to the desired conventional channel position.
  • Page 23 he following information is provided to guide the installation of the optional SmarTrunk II Logic Board. Each step is explained in detail and supported with drawings where required. This installation procedure should be followed carefully to avoid damage to the radio and the option equipment. Before disassembling and reassem- bling the radio, wear a conducting wrist strap to prevent damage to...
  • Page 24 The battery latches are located at the sides of the radio. Slide latches away from the front panel on both sides of the radio to unlock battery compartment (Figure 3-1). b. Slide battery cover down and away from radio to re- move (Figure 3-2).
  • Page 25 Remove the antenna. The antenna screws off counter- clockwise (Figure 3-3). b. Remove the two screws at the back of the chassis (Figure 3-3). Slide the chassis downwards a little and lift it away from the front housing (Figure 3-3). NOTE Please note that the flat ribbon cable still connects the controller board and...
  • Page 26 Dismantle the radio by first removing the chassis from the front housing. (Refer to section 3.1 instructions for disassembling the radio). Orientate the ST-865M3 Logic Board so that the 12 pin male connector is at the lower edge and facing downwards. (See figure 3-4) Attach the ST-865M3 Logic Board to the controller board by inserting the 12 pin male connector into the 12 pin female...
  • Page 27 Slide the chassis upwards to properly fit into the hous- ing and press the bottom of the chassis firmly into place (Figure 3-5). Tighten the two screws on the back of the chassis. NOTE Be careful to loop the flex ribbon cable properly when assembling the chassis onto the housing.
  • Page 28 Replace battery pack by sliding the pack in place. b. Slide battery cover latches towards the front panel to lock. Replace the antenna.
  • Page 29 If the radio does not function correctly, follow the steps in the troubleshooting chart shown in (Figure 3-6). •...

  • Page 30: System Tone

    Program the radio for the SmarTrunk II operating frequencies and the various radio operating parameters required. Refer to the GP68 instruction manual for specific instructions. When the radio programming is complete, the SmarTrunk II Logic Board can be programmed by following the procedure described in Section 4.
  • Page 31 4 • LOGIC BOARD PROGRAMMING he ST-865M3 provides the installing technician a flexible programming capability after the ST-865M3 has been installed in the radio. The ST- 865M3 is programmed by using the keypad on the front of the radio. No special cables or other attachments are required.

  • Page 32: Number Of Trunking Channels

    Model ST-865M3 SmarTrunk II ™ Logic Board Table 4-1 summarizes the programmable features, the keypad sequence for programming, and the default values as provided by the factory. Each feature programmed requires the following steps: Enter a two digit programming code. Press the # key (indicates end of programming code sequence).

  • Page 33: Primary Code

    *Number of Trunking Channels 10# data # *Primary Code *Secondary Code *Priority Subscriber Enable *Five Digit Access Code Return to factory default values 19# *Trunking System ID Number *Automatic PTT Mode *Emergency Call Override Clear Channel Alerting Mode *Radio-Kill *Memory Speed-dialing programming *Conventional Operating Mode...
  • Page 34 Model ST-865M3 SmarTrunk II ™ Logic Board The Primary Code consists of a four digit number that is contained in the SmarTrunk II digital transmission. Any four digit number from 0000 to 9999 may be used. See Section 2 (Operating Modes) before assigning the Pri- mary Code.

  • Page 35: Five Digit Access Code

    4 • ST-865M3 Programming A priority override is possible only if the subscriber engaging the priority override has a higher priority level than the current subscriber on a channel. There are ten priority levels, from 0 (lowest priority) to 9 (highest pri- ority).

  • Page 36: Trunking System Id Number

    Model ST-865M3 SmarTrunk II ™ Logic Board The sequence for programming the five digit access code requires the dealer to enter the five digit number two times. This insures that no mistakes are made dur- ing the entry of a new access code. To change the five digit access code: Enter the program code 16 followed by the # key, then the new five digit access code followed by the # key.

  • Page 37: Automatic Ptt Mode

    4 • ST-865M3 Programming To program the ST-865M3 with a trunking system ID number: Enter the program code 20 followed by the # key, and then the trunking system ID number followed by the # key. Example: To program the Trunking System ID Number to 5 press: The Automatic PTT mode makes radio operation simple for the dispatch operation.

  • Page 38: Clear Channel Alerting Mode

    Example: To enable Clear Channel Alerting press: 2 4 # 1 #. 24 # 0 # disables this function To re-activate a Portable Radio press: 2 5 # 0 #. To disable Memory Speed Dial Programming press: 2 6 # 0 #.
  • Page 39 4 • ST-865M3 Programming This program code enables or disables the ability of the radio to operate in conventional mode on non SmarTrunk channels. To program this function: Enter the program code 23 followed by the # key, then enter 0 or 1 followed by the # key.
  • Page 40 Model ST-865M3 SmarTrunk II ™ Logic Board (This page left blank intentionally)
  • Page 41 APPENDIX A *Number of Trunking Channels 10# data # *Primary Code *Secondary Code *Priority Subscriber Enable *Five Digit Access Code Return to factory default values 19# *Trunking System ID Number *Automatic PTT Mode *Emergency Call Override *Clear Channel Alerting Mode *Radio-Kill *Memory Speed-dialing Programming...
  • Page 42 Model ST-865M3 SmarTrunk™ Logic Board Channel #1 Channel #2 Channel #3 Channel #4 Channel #5 Channel #6 Channel #7 Channel #8 Channel #9 Channel #10 Channel #11 Channel #12 Channel #13 Channel #14 Channel #15 Channel #16 Channel #17 Channel #18 Channel #19 Channel #20...
  • Page 43 APPENDIX B Motorola / SmarTrunk Systems Part Number Cross Reference Chart Item ST-865M3 Kit (1ea.) ST-865M3 Kit (10ea.) ST-865M3 Manual ST-865M3 User Card ST-852M Controller ST-852M Manual • CROSS REFERENCE CHART Motorola P/N SmarTrunk Systems P/N PMLN4066A 502-4500 PMLN4067A 502-4505...
  • Page 44 Model ST-865M3 SmarTrunk™ Logic Board...

This manual is also suitable for:

St-865m3

Table of Contents