NEC SL1100 Hardware Manual
  1. Manuals
  2. Brands
  3. NEC Manuals
  4. Telephone System
  5. SL1100
  6. Hardware manual

NEC SL1100 Hardware Manual

Hide thumbs Also See for SL1100:
Table of Contents

Advertisement

Quick Links

See also: Feature Manual , Hardware Manual
Hardware Manual
A50-031693-004 AU
ISSUE 4.1 (R5.1)
January 2015

Advertisement

Table of Contents
loading

Related Manuals for NEC SL1100

Summary of Contents for NEC SL1100

  • Page 1 Hardware Manual A50-031693-004 AU ISSUE 4.1 (R5.1) January 2015...
  • Page 2 Copyright NEC shall not be liable for any direct, indirect, consequential or incidental damages about the use of this equipment, manual or any related materials. NEC Corporation reserves the right to change the specifications, functions, or features at any time without notice.

  • Page 3: Table Of Contents

    ISSUE 4.1 (R5.1) SL1100 TABLE OF CONTENTS Regulatory Chapter 1 Introduction Section 1 GENERAL INFORMATION..........1-1 Section 2 EQUIPMENT LIST............. 1-2 2.1 KSU and Optional Unit..............1-3 2.1.1 IP4[ ]-1228M-B KSU..............1-3 2.1.2 IP4WW-Battery Box..............1-3 2.2 Trunk/Extension/ISDN Expansion Interface Cards......1-4 2.2.1 IP4WW-080E-B1................
  • Page 4 SL1100 ISSUE 4.1 (R5.1) 1.4 Grounding and AC Cabling............. 2-7 1.4.1 Grounding the KSU............... 2-7 1.4.2 AC Power Requirement..............2-7 1.4.3 AC Power Cord................2-8 1.5 Trunk/Extension Cabling..............2-8 1.5.1 General..................2-8 1.5.2 Precautions for Cabling..............2-9 1.5.3 Trunk Cabling................2-9 1.5.4 Extension Cabling.................
  • Page 5 ISSUE 4.1 (R5.1) SL1100 4.3 VRS/Voice Mail Card (PZ-VM21)..........2-62 4.3.1 General..................2-62 4.3.2 Unpacking................... 2-62 4.3.3 Installing the PZ-VM21 PCB............2-62 4.4 Installing the CF Card (CFVMS)........... 2-65 Section 5 INSTALLING THE MULTILINE TELEPHONES AND OPTIONAL TERMINALS........2-67 5.1 Installing the Multiline Telephones..........2-67 5.1.1 Location of Controls..............
  • Page 6 SL1100 ISSUE 4.1 (R5.1) Chapter 4 Maintenance Section 1 FUSE REPLACEMENT............. 4-1 1.1 Replacing the Fuse................. 4-1 Section 2 LITHIUM BATTERY REPLACEMENT......4-3 2.1 General................... 4-3 2.2 Lithium Battery Specification............4-3 2.3 Replacing the Lithium Battery............4-4 Section 3 MAIN SOFTWARE UPGRADING........4-8 3.1 General...................
  • Page 7 ISSUE 4.1 (R5.1) SL1100 LIST OF TABLES Table 1-1 Memory Capacity of MEMDB-C1............... 1-5 Table 1-2 System Capacity....................1-8 Table 2-1 KSU Packing List....................2-2 Table 2-2 Items on the CPU card..................2-2 Table 2-3 Power Requirement................... 2-7 Table 2-4 RJ61 Cable Connector Pin-Outs (J101-J103)..........2-12 Table 2-5 IP4WW-Battery Box Packing List..............
  • Page 8 SL1100 ISSUE 4.1 (R5.1) LIST OF FIGURES Figure 1-1 System Configuration..................1-1 Figure 1-2 System Image....................1-9 Figure 1-3 Maximum KSU Capacity - Expandability of Trunk and Extension (without PRI)....................1-9 Figure 1-4 Maximum KSU Capacity - Expandability of Trunk and Extension (with PRI)......................
  • Page 9 ISSUE 4.1 (R5.1) SL1100 Figure 2-46 Disconnecting the Battery Connection Cable..........2-32 Figure 2-47 Loosen the Fuse Unit Screw................ 2-32 Figure 2-48 Replacing the Fuse..................2-33 Figure 2-49 Install the Fuse Unit..................2-33 Figure 2-50 Securing the Fuse Unit................. 2-33 Figure 2-51 Connect Battery Connection Cable..............
  • Page 10 SL1100 ISSUE 4.1 (R5.1) Figure 2-99 Setting for High Position................2-69 Figure 2-100 Leg Setting for High Position..............2-69 Figure 2-101 Cabling for Wall-Mount................2-70 Figure 2-102 Wall-Mount Unit - 24TIXH-C............... 2-70 Figure 2-103 Hook-Switch Hanger................... 2-71 Figure 2-104 Wall-Mount Screw Guide................2-71 Figure 2-105 Mounting the Multiline Telephone...............
  • Page 11 ISSUE 4.1 (R5.1) SL1100 Figure 4-14 Display of Multiline Telephone................ 4-8 Figure 4-15 Removing the Sub-Cover................4-9 Figure 4-16 Removing the Main-Cover................4-9 Figure 4-17 Inserting the CF card..................4-10 Figure 4-18 LOAD Button (S1) Location................4-10 Figure 4-19 Removing the CF card.................. 4-11...
  • Page 12 SL1100 ISSUE 4.1 (R5.1) MEMO Hardware Manual...

  • Page 13: Regulatory

    ISSUE 4.1 (R5.1) SL1100 Regulatory BATTERY DISPOSAL The SL1100 system includes the batteries listed below. When disposing of these batteries, KSU, and/or Unit, you must comply with applicable regulations relating to your location regarding proper disposal procedures. Unit Name Type of Battery...
  • Page 14 This equipment must only be installed and maintained by service personnel. In the event of equipment malfunction, all repairs must be performed by an authorised dealer of NEC. It is the responsibility of users requiring service to report the need for service to one of NEC authorised agents.
  • Page 15 POWER FAILURE The NEC SL1100 system is operated on 230VAC Mains power. The System and Terminals will not operate when the mains power fails unless Battery Back-up or a UPS is connected. If emergency telephone use is required a Battery back-up or UPS needs to be connected.
  • Page 16 SL1100 ISSUE 4.1 (R5.1) MEMO Regulatory...

  • Page 17: Chapter 1 Introduction

    The small compact KSU comes with an installed CPU and eight digital and four analogue extension ports and has two stackable slots for further expansion. The SL1100 provides a maximum of 12 analogue trunks and 24 Multiline terminals, and also equipped to support Digital Network (BRI/PRI) and IP Trunks (SIP) or IP extensions.

  • Page 18: Section 2 Equipment List

    SL1100 ISSUE 4.1 (R5.1) 2 EQUIPMENT LIST ECTION The following table lists all equipment for the SL1100 system. Stock Number Equipment Name Equipment Description Note 8503498 SL1100 TDM Basic Kit SL1100 TDM Basic Kit (For AT) <Including> IP4AT-1228M-B KSU, PZ-VM21, IP4WW-...

  • Page 19: Ksu And Optional Unit

    ISSUE 4.1 (R5.1) SL1100 Stock Number Equipment Name Equipment Description Note 4426169 SL-IP-NAPT LIC NAPT License for Multiline IP Telephone (1 license per system) 4426170 SL-VM-CHANNEL-2 LIC Additional InMail Channel License (2 ports) 4426171 SL-VM-ADVANCE LIC InMail Advanced Features License (1 license per sys-...

  • Page 20: Trunk/Extension/Isdn Expansion Interface Cards

    SL1100 ISSUE 4.1 (R5.1) 2.2 Trunk/Extension/ISDN Expansion Interface Cards 2.2.1 IP4WW-080E-B1 The 080E card is installed in the 1228M KSU and provides a total of eight digital ports. Either the analogue trunk daughter board (4COIDB) or the ISDN BRI daughter board (2BRIDB) can be mounted on this card.

  • Page 21: Ip4Ww-2Bridb-C1

    ISSUE 4.1 (R5.1) SL1100 2.2.5 IP4WW-2BRIDB-C1 The 2BRIDB provides two ISDN (Basic Rate) circuit and is mounted on the 084M, 080E, 008E or 000E card. A total of three 2BRIDBs can be installed per system. • Mount this board onto the 084M, 080E, 008E or 000E card.

  • Page 22: Pz-Vm21

    SL1100 ISSUE 4.1 (R5.1) 2.3.3 PZ-VM21 The PZ-VM21 daughter board provides additional Voice Response and Voice Mail functionality using a Compact Flash (CF) interface and a single channel V.34 modem. • Mount this card onto the CPU card (VMDB slot) at Main KSU.

  • Page 23: Ip4[ ]-24Tixh-C Tel

    ISSUE 4.1 (R5.1) SL1100 2.4.3 IP4[ ]-24TIXH-C TEL The 24TIXH-C TEL is an IP multiline telephone featuring: • Programmable keys: 24 • Soft Keys: 4 • LCD: 24 digits x 3 lines with Backlit • Handsfree: Full-duplex • Interface: 2 x RJ45 Ethernet Ports (10Base-T/100Base-TX) for LAN and PC •...

  • Page 24: Section 3 System Capacity

    SL1100 ISSUE 4.1 (R5.1) 3 SYSTEM CAPACITY ECTION 3.1 System Capacity Table 1-2 System Capacity Items 1 KSU (1228) Description Note Expansion Slot System Maximum Port 1KSU: 084M+PRI+080E+4COIDBx2 Trunk Port Max. 1KSU: PRIx1+4COIDB/BRIx2 Trunk Port Analogue 1KSU: 4COIDBx3 on 084M/080E/008E/...

  • Page 25: Ksu Capacity

    ISSUE 4.1 (R5.1) SL1100 Items 1 KSU (1228) Description Note DSP Sender *1. Service Tone receiver, DTMF receiver, Caller ID sender / receiver, MF receiver, MFC receiver *2. Service Tone sender, DTMF sender, MF sender, MFC sender 3.2 KSU Capacity System image of KSU capacity (ISDN, Trunk, Extension) is shown as below.

  • Page 26: Expandability Of Trunk And Extension (With Pri)

    SL1100 ISSUE 4.1 (R5.1) 3.2.2 Expandability of Trunk and Extension (with PRI) Detail of PRI installed KSU (Trunk) Example 1: 084M + 4Trk, 8Ext + 4Trk, PRI x 1 32/38 opt. slot) 080E or 008E + 4COIDB or 2BRIDB 084M + opt.

  • Page 27: Chapter 2 Installation

    Installation 1 INSTALLING THE MAIN KSU ECTION 1.1 Before Installing the KSU 1.1.1 General Precautions • To avoid shock or equipment damage, do not plug in or turn the system power on before completing the installation process. • Avoid working with the Equipment during electrical storms. •...

  • Page 28: Unpacking

    SL1100 ISSUE 4.1 (R5.1) • In dusty areas or in areas where sulfuric gases are produced. • In places where shocks or vibrations are frequent or strong. • In places where water or other fluids comes in contact with the equipment.

  • Page 29: Wall-Mounting The Ksu

    ISSUE 4.1 (R5.1) SL1100 Item Description Ethernet Cable Connection (for SMDR (PC, Printer), PCPro or WebPro….etc) Pin No. Connection J3 (RJ45) 8 765 4321 For the detail of LED (D1 - D5), refer to Figure 4-17 Inserting the CF Card on page 4-10 Table 4-2 CPU LED Indications on page 4-12.

  • Page 30: Mounting Procedure Of Ksu

    SL1100 ISSUE 4.1 (R5.1) Ceiling Minimum 200 mm (7.874″) for ventilation Main KSU Minimum 300 mm (11.811″) Minimum 300 mm (11.811″) Wall Minimum 200 mm (7.874″) for wiring Floor Figure 2-3 Wall Mount of KSU • In the case, the KSU is mounted on Battery Box, refer to...

  • Page 31: Figure 2-5 Screw Positions

    ISSUE 4.1 (R5.1) SL1100 Install four screws into the wall. The screw heads must stand off from the wall about 2.5 mm (0.098″) to 3.5 mm (0.138″). 2.5 mm (0.098″) - 3.5 mm (0.138″) 285 mm (11.221″) 180 mm (7.087″) 285 mm (11.221″)

  • Page 32: Figure 2-7 Removing The Sub-Cover

    SL1100 ISSUE 4.1 (R5.1) Pull out the Sub-Cover by pushing out the tabs. Sub-Cover Figure 2-7 Removing the Sub-Cover • The Sub-Cover can be opened and held in the open position. Push to hold Open Figure 2-8 Sub-Cover Open Position Align the four holes on the back of the KSU with the four screws installed in the wall.

  • Page 33: Grounding And Ac Cabling

    ISSUE 4.1 (R5.1) SL1100 1.4 Grounding and AC Cabling The ETH (Earth Ground Lug) is located near the power supply on the KSU. The Sub-Cover must be opened in order to access to it. 1.4.1 Grounding the KSU Ensure Main KSU are powered off and unplug the AC cord.

  • Page 34: Ac Power Cord

    SL1100 ISSUE 4.1 (R5.1) 110VAC 120VAC 220VAC 230VAC 240VAC Frequency 47 Hz - 63 Hz (Rated Frequency: 50/60 Hz) Phase and Wire Single Phase, 2 Line + PE Type Ground Requirement No.14 AWG Copper Wire Feeding Voltage SLT: 20 mA/ -27 V...

  • Page 35: Precautions For Cabling

    • Aerial distribution wiring is not allowed. • Trunks must be installed with lightning protectors. • Do not install the Topaz Terminal in the SL1100 system, it does not work properly. 1.5.3 Trunk Cabling Trunk cabling is required for the 4COIDB, 2BRIDB or 1PRIU PCBs.

  • Page 36: Figure 2-12 Digital Extension Cabling

    SL1100 ISSUE 4.1 (R5.1) J421 J103 J431 J411 J102 J101 ESI 5-8 ESI 1-4 Port 1 Port 2 Port 3 Port 4 T: Tip Max cable length R: Ring 24AWG ( 0.5 mm) Modular Cable 300 m (2-wire, Straight) MLT, DSS (984.3 ft)

  • Page 37: Figure 2-13 Analog Extension Cabling

    ISSUE 4.1 (R5.1) SL1100 J421 J103 J431 J411 J102 J101 SLI 9-12 /DPH 1-2 Port 1 Port 2 Port 3 Port 4 T : Tip R : Ring Modular Cable Max cable length (2-wire, Straight) 24AWG ( 0.5 mm) 1,125 m...

  • Page 38: Cable Routing And Clamping

    SL1100 ISSUE 4.1 (R5.1) Table 2-4 RJ61 Cable Connector Pin-Outs (J101-J103) Pin No. ESI 1-4 (J101), ESI 5-8 (J102): SLI 9-12/DPH 1-2 (J103): Ana- 2-Wire Digital Extension Port logue Extension Port Connector Connector (RJ-61) (RJ-61) T4 (Tip for port 4)

  • Page 39: Figure 2-15 Sub-Cover

    ISSUE 4.1 (R5.1) SL1100 Cut and remove the Plastic Knockouts as needed from the Sub-Cover. Sub-Cover Plastic Knockouts Figure 2-15 Sub-Cover Replace the Sub-Cover. Hardware Manual 2-13...

  • Page 40: Section 2 Installing The External Backup Battery

    • An optional (locally procured), external battery source can be used to provide power during a power failure. • One KSU must have own IP4WW-Battery Box. Do not connect the DX2E-32i/NX7E Topaz Battery Box to the SL1100 system. Damage to equipment or property may result. 2.2 Unpacking Unpack the IP4WW-Battery Box and check it against the following list.

  • Page 41: Battery Box Dimensions

    ISSUE 4.1 (R5.1) SL1100 2.3 Battery Box Dimensions 230 mm (9.055″) 340 mm (13.386″) 500 mm (19.685″) Figure 2-16 Dimension of the IP4WW-Battery Box 2.4 Battery Specifications Table 2-6 Battery Specifications Item Data Capacity 12 V, 7.0 Am/H or equivalent (Voltage must be 12 V) Recommended Battery GS Yuasa NP7-12 (151 x 65 x 97.5 mm / 2.7 kg)

  • Page 42: Figure 2-17 Removing The Front Cover

    SL1100 ISSUE 4.1 (R5.1) Loosen two screws and remove the Front Cover. Two screws (with stopper) Front Cover Figure 2-17 Removing the Front Cover Disconnect the Battery Connection Cable from the Fuse Unit if the cable is plugged already. Battery Connection Cable...

  • Page 43: Figure 2-19 Batt Stopper

    ISSUE 4.1 (R5.1) SL1100 Loosen the screw and lift the Batt Stopper. Batt Stopper Screw Figure 2-19 Batt Stopper Pull out the Battery tray. Battery tray Figure 2-20 Pulling out the Battery Tray Loosen two screws and remove the Battery tray cover.

  • Page 44: Figure 2-21 Remove The Battery Tray Bracket

    SL1100 ISSUE 4.1 (R5.1) Remove two screws and remove the Battery tray bracket. Two screws (with stopper) Battery tray cover Two screws (M3 X 8) Battery tray bracket Figure 2-21 Remove the Battery Tray Bracket Install two batteries into the Battery tray.

  • Page 45: Figure 2-23 Connecting The Battery Cables

    ISSUE 4.1 (R5.1) SL1100 Connect the battery cables. Battery Connection Cable (black) Terminal Terminal (black) (black) Battery Connection Cable (red) Terminal Terminal (red) (red) Battery Connection Cable (blue) Two batteries < Front View > Figure 2-23 Connecting the Battery Cables Incorrect installation of batteries may damage the Fuse Unit or cause possible fire.

  • Page 46: Figure 2-25 Inserting The Battery Tray

    SL1100 ISSUE 4.1 (R5.1) 11. Insert the Battery tray into the Battery Box. Battery tray Figure 2-25 Inserting the Battery Tray 12. Set the Batt Stopper bracket in place and secure with screw. Batt Stopper Screw Figure 2-26 Secure Batt Stopper Bracket...

  • Page 47: Mounting The Ip4Ww-Battery Box

    ISSUE 4.1 (R5.1) SL1100 13. Plug the Battery Connection Cable into the Fuse unit. Battery Connection Cable Fuse unit Figure 2-27 Connecting the Battery Connection Cable 14. Align tabs a to f to holes A to F on Battery Box. Slide the Front cover and tighten the two screws.

  • Page 48: Figure 2-29 Bases And Support Of The Battery Box

    SL1100 ISSUE 4.1 (R5.1) Assemble the FM/WM Base-F, Base-R and WM Support. FM/WM Base-R WM Support FM/WM Base-F Figure 2-29 Bases and Support of the Battery Box Refer to Figure 2-30 Floor-Mount Spacing Guide on page 2-22 for required spacing before drilling holes for 10 mm (0.394″) anchor bolts (locally procured).

  • Page 49: Wall-Mounting The Ip4Ww-Battery Box

    ISSUE 4.1 (R5.1) SL1100 Using the four hooks on the FM/WM Base mount the IP4WW-Battery Box on the Base. IP4WW-Battery Box Hooks Hooks FM/WM Base FM/WM Base Hooks Hooks Figure 2-31 Mounting the Battery Box Using four supplied screws, secure the IP4WW-Battery Box to the FM/WM Base.

  • Page 50: Figure 2-33 Assemble Battery Box Base

    SL1100 ISSUE 4.1 (R5.1) Plywood should first be installed on the wall where the Battery Box will be positioned. This allows secure anchoring of the screws which support the weight of the Battery Box. Using four supplied screws, secure the WM Support to the FM/WM Base-F and Base-R.
  • Page 51 ISSUE 4.1 (R5.1) SL1100 Using anchor bolts, secure the FM/WM Base to the wall. Wall Front side Front side Anchor bolt location AC inlet AC inlet side side Anchor bolt location Four Anchor bolts M10 mm (0.394″) : Maintenance space...

  • Page 52: Figure 2-35 Removing The Front Cover

    SL1100 ISSUE 4.1 (R5.1) Loosen two screws and remove the Front Cover. Two screws (with stopper) Front Cover Figure 2-35 Removing the Front Cover Using the four hooks on the FM/WM Base mount the IP4WW-Battery Box to the Base. Square hole...

  • Page 53: Mounting One Ksu On The Battery Box

    ISSUE 4.1 (R5.1) SL1100 Using one supplied screw (M3x6 with washer), secure the back plane of the Battery Box to the FM/WM Base. Two screw holes (Use either one) < Front view> Figure 2-37 Securing the Battery Box 2.6.3 Mounting One KSU on the Battery Box Before wall-mounting or floor-mounting the IP4WW-Battery Box, a single KSU can be mounted on the Battery Box.

  • Page 54: Figure 2-39 Removing The L-Bracket

    SL1100 ISSUE 4.1 (R5.1) Loosen two screws and remove the L-Bracket. L-Bracket Two screws (M4 X 8) Figure 2-39 Removing the L-Bracket Turn the L-Bracket upside down. Rotate the L-Bracket 180 degrees so that the upper FACE as shown in...

  • Page 55: Figure 2-40 Securing The L-Bracket And Wm Hook

    ISSUE 4.1 (R5.1) SL1100 Using two anchor bolts (locally procured), secure the WM Hook to the wall. The WM Hook is required for securing both Floor-mount and Wall-mount cases. Anchor Bolts WM Hook Two screws (M4 X 8) L-Bracket Two screws...

  • Page 56: Ip4Ww-Battery Box To Ksu Connection

    Figure 2-42 KSU Mounting on Battery Box 2.7 IP4WW-Battery Box to KSU Connection Do not connect the DX2E-32i/NX7E Topaz Battery Box to the SL1100 system. Damage to equipment or property may result. • Make sure the system power is off.

  • Page 57: Ip4Ww-Battery Box Fuse Replacement

    ISSUE 4.1 (R5.1) SL1100 Cut and remove Plastic Knockout from the Sub-Cover to connect Battery cable. Plastic Knockout Sub-Cover Battery cable Figure 2-44 Connecting Battery Cable Connect Battery cable from the Battery box to Battery connector on the KSU. 2.8 IP4WW-Battery Box Fuse Replacement •...

  • Page 58: Figure 2-46 Disconnecting The Battery Connection Cable

    SL1100 ISSUE 4.1 (R5.1) Disconnect the Battery connection cable from the Fuse Unit. Battery Connection Cable Fuse Unit Figure 2-46 Disconnecting the Battery Connection Cable Loosen the screw from the Fuse Unit. Fuse Unit Screw Figure 2-47 Loosen the Fuse Unit Screw Slide Fuse Unit out of the Battery box.

  • Page 59: Figure 2-48 Replacing The Fuse

    ISSUE 4.1 (R5.1) SL1100 Replace the fuse (250VT8AL). Fuse Unit 250VT8AL Fuse Fuse Unit guide Figure 2-48 Replacing the Fuse Using the Fuse Unit guides, slide the Fuse Unit into the Battery Box. Fuse Unit Fuse Unit guide Figure 2-49 Install the Fuse Unit Secure the Fuse Unit by tightening the screw.

  • Page 60: Figure 2-51 Connect Battery Connection Cable

    SL1100 ISSUE 4.1 (R5.1) Reconnect the Battery Connection Cable to the Fuse Unit. Battery Connection Cable Fuse Unit Figure 2-51 Connect Battery Connection Cable 10. Align tabs a to f to holes A to F on Battery Box. Slide the Front Cover into position and tighten the two screws.

  • Page 61: Cards

    ISSUE 4.1 (R5.1) SL1100 3 INSTALLING THE EXPANSION INTERFACE CARDS ECTION 3.1 General Up to two expansion interface cards can be installed per KSU. Table 2-7 Expansion Cards Expansion Interface Description Note Card IP4WW-080E-B1 8 digital extensions card IP4[ ]-008E-B1...

  • Page 62: Mounting The Expansion Interface Card

    SL1100 ISSUE 4.1 (R5.1) Items List of Contents Note IP4WW-000E-B1 000E-B1 PCB (with PKG Spacer) Nylon Spacers Metal Spacers Screws (with circular washer) IP4WW-2BRIDB-C1 2BRIDB-C1 PCB Nylon Spacers 2BRI Label Metal Spacers Screws (with circular washer) IP4WW-1PRIU-C1 1PRIU-C1 PCB (with PKG Spacer)

  • Page 63: Figure 2-54 Removing The Main-Cover

    ISSUE 4.1 (R5.1) SL1100 Loosen two screws and remove the Main-Cover. Main-Cover Two screws Hooks Figure 2-54 Removing the Main-Cover Insert two Nylon-spacers into the specified holes, and fasten two Metal-spacers into the specified holes. (Both Nylon and Metal spacers are provided with 080E/008E/000E/1PRIU) If no more Expansion Interface cards are to be mounted on the 1st PCB, fasten two screws to secure the 1st PCB on the top of the 080E/008E/000E/1PRIU.

  • Page 64: Figure 2-56 Mounting The 2Nd Expansion Interface Card

    SL1100 ISSUE 4.1 (R5.1) In case a 2nd PCB is mounted, insert two Nylon-spacers into the specified holes, and fasten two Metal-spacers into the specified holes. (Both Nylon and Metal spacers are provided with 080E/ 008E/000E/1PRIU) Fasten two screws to secure the 2nd PCB to the top of the 080E/008E/000E/1PRIU.

  • Page 65: Figure 2-58 Plastic Knockouts

    ISSUE 4.1 (R5.1) SL1100 Cut and remove the Plastic Knockouts as required for each Expansion interface card. EXP.1st PCB Main-Cover EXP.2nd PCB Plastic Knockouts Figure 2-58 Plastic Knockouts Replace the Main-Cover and fasten two screws. Main-Cover Two screws Hooks Figure 2-59 Replacing the Main-Cover...

  • Page 66: Mounting The 4Coidb Pcb

    SL1100 ISSUE 4.1 (R5.1) 3.3.2 Mounting the 4COIDB PCB Cut and remove specified Plastic Knockouts on the 084M-B1/080E-B1/008E-B1/000E-B1 PCB. Plastic Knockout 084M-B1 Plastic Plastic Knockouts Knockout 080E-B1/008E-B1 000E-B1 Figure 2-60 Plastic Knockouts on 084M-B1/080E-B1/008E-B1/000E-B1 Insert two Nylon-spacers into the specified holes. Using supplied screw, fasten Metal Spacer to 4COIDB-B1 PCB.

  • Page 67: Figure 2-62 Mounting The 4Coidb-B1 Into The Ksu

    ISSUE 4.1 (R5.1) SL1100 The 4COIDB-B1 cannot be mounted on the 1PRIU-C1 PCB. Mount the 4COIDB-B1 with 084M-B1/080E-B1/008E-B1/000E-B1 PCB into the KSU. Screws 084M-B1/080E-B1/008E-B1/000E-B1 PCB and 4COIDB-B1 PCB Nylon- Spacers Metal-Spacers Figure 2-62 Mounting the 4COIDB-B1 into the KSU Replace the Main-Cover and fasten two screws.

  • Page 68: Mounting The 2Bridb Pcb

    SL1100 ISSUE 4.1 (R5.1) 3.3.3 Mounting the 2BRIDB PCB Set the switches on the 2BRIDB-C1 PCB before mounting onto the 084M- B1/080E-B1/008E-B1/000E-B1 PCB, refer to the Switch Setting on page 2-49. Cut and remove specified Plastic Knockouts on the 084M-B1/080E-B1/008E-B1/000E-B1 PCB.
  • Page 69 ISSUE 4.1 (R5.1) SL1100 Attach the 2BRI Label to the specified position on the 084M-B1/080E-B1/008E-B1/000E-B1 PCB. 2BRIDB-C1 PCB Screw Nylon-Spacers Metal-Spacer 2BRI Label 084M-B1/080E-B1/008E-B1 Screw /000E-B1 PCB Figure 2-65 Installing the 2BRIDB-C1 The 2BRIDB-C1 cannot be mounted on the 1PRIU-C1 PCB.

  • Page 70: Cabling And Setting The Expansion Interface Card

    SL1100 ISSUE 4.1 (R5.1) Mount the 2BRIDB-C1 with 084M-B1/080E-B1/008E-B1/000E-B1 PCB into the KSU. Screws 084M-B1/080E-B1/008E-B1/000E-B1 PCB and 2BRIDB-C1 PCB Nylon- Spacers Metal-Spacers Figure 2-66 Mounting the 2BRIDB-C1 into the KSU Replace the Main-Cover and fasten two screws. Main-Cover Two screws...

  • Page 71: Cabling Ip4Ww-080E-B1

    • Aerial distribution wiring is not allowed. • Trunks must be installed with lightning protectors. • Only SL1100 terminals (12TXH, 24TXH) may be connected to a SL1100 digital port. Do not connect any other terminal as damage may result. 3.4.1 Cabling IP4WW-080E-B1 This IP4WW-080E-B1 PCB provides two RJ-61 connections for digital extensions.

  • Page 72: Cabling Ip4[ ]-008E-B1

    Before plugging in the Multiline Telephone, DSS Console, Single line Telephone or Doorphone, ensure Main KSU is powered off. Only SL1100 terminals (12TXH, 24TXH) may be connected to a SL1100 digital port. Do not connect any other terminal as damage may result.

  • Page 73: Cabling Ip4Ww-000E-B1

    ISSUE 4.1 (R5.1) SL1100 While an Analogue Telephone (port) is ringing or MW-lamp is flashing on an Analogue Phone (port), do not disconnect the phone from the port and or connect another type of the terminal to this port. 3.4.2.1 Connectors The following table shows the pin-outs for the RJ-61 cable connector for Analogue extension connections.

  • Page 74: Cabling And Setting Ip4Ww-2Bridb-C1

    SL1100 ISSUE 4.1 (R5.1) 3.4.4.1 Connectors The following table shows the pin-outs for the RJ-61 cable connector for CO (J2) and PF (J3) connections. Table 2-11 RJ-61 CO/PF Pin-Outs (J2, J3) Pin No. CO1-4 (J2): CO Port Connector PF1 (J3): PF Tel Port Connector...

  • Page 75: Table 2-12 Rj-61 Bri Pin-Outs (S-Bus, T-Bus)

    ISSUE 4.1 (R5.1) SL1100 Table 2-12 RJ-61 BRI Pin-Outs (S-Bus, T-Bus) Pin No. RJ-61 Cable Connec- RJ-61 Cable Connector-2BRIDB- tor-2BRIDB-J2 (BRI1), J3 J2 (BRI1), J3 (BRI2) T-Bus Con- (BRI2) S-Bus Connection nection 8 765 4321 3.4.5.2 Switch Setting Figure 2-72 Switches Location of 2BRIDB-C1 on page 2-50 shows the location of the connectors and switches on the IP4WW-2BRIDB-C1.

  • Page 76: Cabling And Setting Ip4Ww-1Priu-C1

    SL1100 ISSUE 4.1 (R5.1) Connect the cables from the NT1 Network Termination cable to the J2 or J3 connector on the 2BRIDB-C1 daughter board. Connector J2 - BRI1: Use switches J12, J13, J14 Connector J3 - BRI2: Use switches J15, J16, J17 Ensure that you set all switches correctly for each BRI circuit.

  • Page 77: Table 2-14 Rj-45 Pri Pin-Outs (S-Bus, T-Bus)

    ISSUE 4.1 (R5.1) SL1100 3.4.6.1 Connector Following table shows the pin-outs for the RJ-45 cable connector for S-Bus and T-Bus RJ-45 connections. Table 2-14 RJ-45 PRI Pin-Outs (S-Bus, T-Bus) Pin No. RJ-45 Cable Connector- PRI 1 RJ-45 Cable Connector- PRI 1...

  • Page 78: Table 2-16 Led Indication

    SL1100 ISSUE 4.1 (R5.1) IP4WW-1PRIU-C1 1.5M 2M 1.5M J8/9 D3 D4 PRI 1 (Red) (Green) Figure 2-74 Switches and LEDs Location of 1PRIU-C1 3.4.6.3 LED Indication LED indications for the IP4WW-1PRIU-C1 are listed in following table. Each LED is listed with its associated function and LED and operational status.

  • Page 79: Power Failure Transfer (4Coidb-B1 Only)

    ISSUE 4.1 (R5.1) SL1100 LED Indication Operation Status Remarks Live LED (D4) Busy LED (D3) (Green) (Red) Unit Busy A Channel is busy (use another from Ch1 - Chx) All channels are Idle. Flash 80ms (On/ Downloading firmware Off) x3/ 400ms 3.5 Power Failure Transfer (4COIDB-B1 only)

  • Page 80: Section 4 Installing The Optional Interface Cards

    SL1100 ISSUE 4.1 (R5.1) 4 INSTALLING THE OPTIONAL INTERFACE CARDS ECTION 4.1 Installing the Expansion Memory Card (MEMDB-C1) 4.1.1 General The Memory expansion daughter board (IP4[ ]-MEMDB-C1) provides additional memory for the system to use following features; • To use VoIP Card (IP4WW-VOIPDB-C1) •...

  • Page 81: Figure 2-76 Removing The Main-Cover

    ISSUE 4.1 (R5.1) SL1100 Loosen two screws and remove the Main-Cover. Main-Cover Two screws Hooks Figure 2-76 Removing the Main-Cover Press tab A and lift the CPU support bracket. Remove the CPU card. CPU card CPU support 084M-B1 at 1228M KSU...

  • Page 82: Figure 2-78 Installing The Memdb Pcb

    SL1100 ISSUE 4.1 (R5.1) Insert the MEMDB-C1 daughter board to J4 socket on the CPU card and press down the MEMDB-C1 daughter board to secure. Both levers must be secured to notch-A. Notch-A Notch-B Lever MEMDB-C1 PCB CPU card Figure 2-78 Installing the MEMDB PCB Reinstall the CPU card into the 084M-B1 mother board, and close the CPU support making sure the tab A locks into place.

  • Page 83: Voip Card (Voipdb-C1)

    ISSUE 4.1 (R5.1) SL1100 Replace the Main-Cover and fasten two screws. Main-Cover Two screws Hooks Figure 2-80 Replacing the Main-Cover 4.2 VoIP Card (VOIPDB-C1) 4.2.1 General The IP4WW-VOIPDB-C1 daughter board is used to convert the RTP (Real Time Transfer Protocol) packets via the IP Network and PCM highway.

  • Page 84: Figure 2-81 Removing The Sub-Cover

    SL1100 ISSUE 4.1 (R5.1) Open and remove the Sub-Cover. Sub-Cover Sub-Cover Figure 2-81 Removing the Sub-Cover Loosen two screws and remove the Main-Cover. Main-Cover Two screws Hooks Figure 2-82 Removing the Main-Cover 2-58 Installation...

  • Page 85: Figure 2-83 Removing The Cpu Card

    ISSUE 4.1 (R5.1) SL1100 Press tab A and lift the CPU support bracket. Remove the CPU card. CPU card CPU support 084M-B1 at 1228M KSU Figure 2-83 Removing the CPU Card Install the VOIPDB-C1 daughter board to J5 connector on the CPU card.

  • Page 86: Figure 2-85 Installing The Cpu Card

    SL1100 ISSUE 4.1 (R5.1) Reinstall the CPU card into the 084M-B1 mother board, and close the CPU Support making sure tab A locks into place. CPU card CPU support 084M-B1 at 1228M KSU Figure 2-85 Installing the CPU Card Cut and remove the Plastic Knockout for VoIP connector, then replace the Main-Cover and fasten two screws.

  • Page 87: Led Indication

    Pass 2 times to HUB < Bottom View > Figure 2-87 Connecting a LAN Cable Refer to the SL1100 Programming Manual for detailed programming instructions. The VoIP feature requires system configuration. 4.2.4 LED Indication LED indications for the IP4WW-VOIPDB-C1 are listed...

  • Page 88: Vrs/Voice Mail Card (Pz-Vm21)

    SL1100 ISSUE 4.1 (R5.1) Table 2-19 VOIPDB LED Indications Function LED Status Operation status Link activity or data transmission and re- On Green LED lights when link up is completed. LED flash ception. when data is transmitting or receiving. LINK1000...

  • Page 89: Figure 2-89 Removing The Sub-Cover

    ISSUE 4.1 (R5.1) SL1100 Open and remove the Sub-Cover. Sub-Cover Sub-Cover Figure 2-89 Removing the Sub-Cover Loosen two screws and remove the Main-Cover. Main-Cover Two screws Hooks Figure 2-90 Removing the Main-Cover Hardware Manual 2-63...

  • Page 90: Figure 2-91 Removing The Cpu Card

    SL1100 ISSUE 4.1 (R5.1) Press tab A and lift the CPU support bracket. Remove the CPU card. CPU card CPU support 084M-B1 at 1228M KSU Figure 2-91 Removing the CPU Card Connect the PZ-VM21 daughter board to the J6 connector using four Nylon-spacers on the CPU card.

  • Page 91: Installing The Cf Card (Cfvms)

    ISSUE 4.1 (R5.1) SL1100 Reinstall the CPU card into the 084M-B1 mother board, and close the CPU Support making sure tab A locks into place. CPU card CPU support 084M-B1 at 1228M KSU Figure 2-93 Installing the CPU Card Replace the Main-Cover and fasten two screws.

  • Page 92: Figure 2-95 Installing The Cf Card

    SL1100 ISSUE 4.1 (R5.1) Remove the CPU card and insert the compact flash card into the CF slot (CN2). CF card CPU card CF Slot (CN2) PZ-VM21 PCB Figure 2-95 Installing the CF Card Reinstall the CPU card into the 084M-B1 mother board, and close the CPU Support making sure tab A locks into place.

  • Page 93: And Optional Terminals

    ISSUE 4.1 (R5.1) SL1100 5 INSTALLING THE MULTILINE TELEPHONES AND ECTION OPTIONAL TERMINALS 5.1 Installing the Multiline Telephones There are three types of Multiline Telephones available in the SL1100 system. • IP4WW-12TXH-B-TEL • IP4WW-24TXH-B-TEL • IP4WW-24TIXH-C-TEL (IP) 5.1.1 Location of Controls Handset...

  • Page 94: Multiline Telephone Legs Adjustment

    SL1100 ISSUE 4.1 (R5.1) Functions 12TXH 24TXH 24TIXH Backlit Dial Pad Incoming LED 2 colors (Red/Green) Connected to Digital Extension Port Ethernet Port on the Network Headset Port Power Feeding AC Adapter (DC27 V,1 A) or PoE (IEEE802.3af) 5.1.2 Multiline Telephone Legs Adjustment The Multiline Telephone provides adjustable legs for angling the phone to best suit each user.

  • Page 95: Figure 2-99 Setting For High Position

    ISSUE 4.1 (R5.1) SL1100 5.1.2.2 High position setting Turn telephone over (button side down). Pull up the Leg Stoppers. Leg Stopper Figure 2-99 Setting for High Position Adjust the leg to desired height. < High position > Figure 2-100 Leg Setting for High Position Lead the Line and Handset cords through the applicable grooves.

  • Page 96: Wall-Mounting The Multiline Telephone

    SL1100 ISSUE 4.1 (R5.1) 5.1.3 Wall-Mounting the Multiline Telephone Arrange the cables and put down the leg as shown below. Handset cord Telephone line cord < Bottom view> Figure 2-101 Cabling for Wall-Mount For IP4WW-24TIXH-C only: When wall-mounting the IP4WW-24TIXH-C, attach the IP4WW-WALL MOUNT UNIT to the bottom panel as shown.

  • Page 97: Figure 2-103 Hook-Switch Hanger

    ISSUE 4.1 (R5.1) SL1100 Remove the switch-hook from the unit. Turn the tab toward the top. Then slide the hook-switch into position. Refer to Figure 2-103 Hook-Switch Hanger on page 2-71. Hook-switch hanger Hook-switch hanger Figure 2-103 Hook-Switch Hanger Install two screws into a wall. The screw heads must be remained about 3 mm (0.12″).

  • Page 98: Install The Ip Multiline Telephone (Ip4Ww-24Tixh-C1 Tel)

    SL1100 ISSUE 4.1 (R5.1) 5.2 Install the IP Multiline Telephone (IP4WW-24TIXH-C1 TEL) 5.2.1 System Connection The IP Multiline Telephone is connected via HUB. IP Multiline Telephone LAN Cable Exit Help (10BASE-T/100BASE-TX) Flash Transfer Mute PQRS WXYZ Clear/Back Speaker Hold Ferrite Core...

  • Page 99: Applying Power To The Ip Multiline Telephone

    ISSUE 4.1 (R5.1) SL1100 5.2.3 Applying Power to the IP Multiline Telephone IP Multiline Telephone (IP4WW-24TIXH-C1) supports two different power sources for the Telephone. • ACA-UA/ AC-LE UNIT Plug the Optional AC[ ]-[ ] AC adapter input jack in the telephone base unit, and plug the 2-prong wall plug of the AC adapter in AC outlet.

  • Page 100: Figure 2-109 Cabling Of Dss

    SL1100 ISSUE 4.1 (R5.1) Lead the Line cord through the applicable grooves. Figure 2-109 Cabling of DSS 5.3.1.2 High position setting Turn DSS Console over (button side down). Pull up the Leg Stoppers. Leg Stopper Figure 2-110 Leg Stopper of DSS Console...

  • Page 101: Wall-Mounting The Dss Console

    ISSUE 4.1 (R5.1) SL1100 Adjust the leg to desired height. < High position > Figure 2-111 High Position Setting Lead the Line cord through the applicable grooves. (Refer to Figure 2-109 Cabling of DSS on page 2-74) 5.3.2 Wall-Mounting the DSS Console Lift the leg and lead the cable through the applicable grooves.

  • Page 102: Installing The Headset

    SL1100 ISSUE 4.1 (R5.1) Install two screws into a wall. The screw heads must be remained about 3 mm (0.12″). 3 - 4 mm 1 - 3 mm (0.12″ - 0.16″) (0.04″ - 0.12″) 83.5 mm (3.287″) 7 - 9.5 mm (0.28″...

  • Page 103: Installing The Doorphone Box

    ISSUE 4.1 (R5.1) SL1100 Connect the Headset cord into the Headset socket. Headset socket < Bottom view> Figure 2-115 Headset Socket (2-wire Multiline Telephone) Headset socket AN(=) PC(X) LAN(=) < Bottom view> Figure 2-116 Headset Socket (IP Multiline Telephone) The headset configuration is assigned using system programming.

  • Page 104: Figure 2-117 Doorphone Box And Bracket

    SL1100 ISSUE 4.1 (R5.1) Connect the cable to the screw terminals on the Doorphone box. (No polarity sensitive) Wall-mount bracket Upper housing Screw terminals Screw Connect cable Figure 2-117 Doorphone Box and Bracket Mount the Wall-Mount bracket on the wall using supplied screws.

  • Page 105: Connecting The Doorphone

    ISSUE 4.1 (R5.1) SL1100 5.5.2 Connecting the Doorphone J421 J103 J431 J411 J102 J101 RY1/2 SLI 9-12 /DPH 1-2 Port 1 Port 2 Port 3 Port 4 T : Tip R : Ring Modular Cable (2-wire, Straight) Doorphone Figure 2-119 Connecting the Doorphone The Doorphone configuration is assigned using system programming.

  • Page 106: Table 2-24 Rj-61 General Purpose/Door Unlock Relay Control Connector (J7)

    SL1100 ISSUE 4.1 (R5.1) J7 (RJ61) 8 765 4321 RY1/2 Door unlock control devices Figure 2-120 Connecting the Door Unlock Device The following table shows the pin-outs for the RJ-61 cable connector. Table 2-24 RJ-61 General Purpose/Door Unlock Relay Control Connector (J7) Pin No.

  • Page 107: Installing The External Paging Speaker/External Moh/Bgm Sources

    ISSUE 4.1 (R5.1) SL1100 5.7 Installing the External Paging Speaker/External MOH/BGM Sources 5.7.1 Connecting the Audio Equipment • The audio jack labeled PAGE, MOH, BGM can be used for audio port (External paging, External MOH, BGM) • Audio port configuration is assigned using system programming.

  • Page 108: Bgm/External Moh Source Input Specifications

    SL1100 ISSUE 4.1 (R5.1) 5.7.3 BGM/External MOH Source Input Specifications Table 2-27 BGM/External MOH Source Input Specifications Item Specification Input Impedance 600 Ω @ 1 kHz Input Level Nominal 250 mV (-10 dBm) Maximum Input 1 V RMS 5.8 SMDR (Station Message Detail Recording) 5.8.1 General...

  • Page 109: Chapter 3 System Start Up

    System Start Up 1 SYSTEM START UP ECTION 1.1 Before Starting Up the System Before starting up the system, make sure: • KSU is installed correctly. • All extensions are cabled correctly. • Earth ground and PSTN Trunks are cabled correctly. •...

  • Page 110: Perform A Cold Start

    SL1100 ISSUE 4.1 (R5.1) 1.2.1 Perform a Cold Start This section describes the process for starting the system for the first time or starting a system that requires the customer data be deleted. System software is loaded from flash memory, and the customer data is deleted from RAM memory.

  • Page 111: Perform A Hot Start

    ISSUE 4.1 (R5.1) SL1100 Continue holding the LOAD button (S1) for approximately three seconds or until Status LED (D5) starts flashing red. RUN LED LED (D5) < Front view > Figure 3-4 Status LED (D5) and RUN LED Location Release the LOAD button.

  • Page 112: Section 2 Programming Mode

    Base Service OP1 OP2 Figure 3-7 Entering Programming Mode Display 2 For the details of programming, refer to the SL1100 Programming Manual. (separate issue) 2.2 Exiting the Programming Mode Press Mute key several times to return to the "Program Mode" Screen.

  • Page 113: Saving (Backup) The Customer Data

    ISSUE 4.1 (R5.1) SL1100 2.3 Saving (Backup) the Customer Data When the installer/system administrator exits from the programming mode, the system will automatically save the customer data to the on-board memory which is backed up by lithium battery. Additionally, the customer data can be saved to a CF Card for backup purpose. The PZ-VM21 daughter board must be installed to the CPU card with a BLANK CF card inserted.

  • Page 114: Figure 3-13 Inserting The Cf Card

    SL1100 ISSUE 4.1 (R5.1) For the details of PZ-VM21 daughter board installation, refer to Installing the PZ-VM21 PCB on page 2-62. Turn the power off, insert the Customer Data CF card into the CF Slot on PZ-VM21. CPU card CF Slot (CN2)

  • Page 115: Section 3 System Shut Down

    ISSUE 4.1 (R5.1) SL1100 3 SYSTEM SHUT DOWN ECTION 3.1 Powering Off the System Turn the KSU power off using the power switch. Figure 3-16 Power Switch Location • DO NOT power off by disconnecting the AC (or DC for battery backup) power.
  • Page 116 SL1100 ISSUE 4.1 (R5.1) MEMO System Start Up...

  • Page 117: Chapter 4 Maintenance

    Maintenance 1 FUSE REPLACEMENT ECTION 1.1 Replacing the Fuse This fuse is only for external battery box connection, it is not used for AC power to the system. Turn off the system power and disconnect AC cord. Open and remove the Sub-Cover. Sub-Cover Sub-Cover Figure 4-1 Removing the Sub-Cover...

  • Page 118: Figure 4-3 Exchanging The Fuse

    SL1100 ISSUE 4.1 (R5.1) Exchange the fuse (250 V/8 A) on 084M-B1 PCB. 084M-B1 FUSE (8 A / 250 V) < Top View > Figure 4-3 Exchanging the Fuse Replace the Main-Cover and fasten two screws. Main-Cover Two screws Hooks...

  • Page 119: Section 2 Lithium Battery Replacement

    Before replacing the Lithium battery, make sure which type of Lithium battery is required and prepare the new Lithium battery. (CR2032) NEC recommends that a backup of the customer data is performed before powering off the system (either PCPro file or CF card backup) in order to replace the backup battery.

  • Page 120: Replacing The Lithium Battery

    SL1100 ISSUE 4.1 (R5.1) 2.3 Replacing the Lithium Battery Remove the Sub-Cover at the Main KSU. Sub-Cover Figure 4-6 Removing the Sub-Cover Power off the system, and remove the AC plug from the AC outlet. Disconnect the AC power cord from the KSU.

  • Page 121: Figure 4-8 Removing The Main-Cover

    ISSUE 4.1 (R5.1) SL1100 Loosen two screws and remove the Main-Cover. Main-Cover Two screws Hooks Figure 4-8 Removing the Main-Cover Press tab A and lift the CPU support bracket. Remove CPU card from the Main KSU. CPU card CPU support...

  • Page 122: Figure 4-10 Location Of Lithium Battery Socket

    SL1100 ISSUE 4.1 (R5.1) Refer to following figure for the Lithium battery location on the CPU card. CPU card Battery socket < Conductor side > Figure 4-10 Location of Lithium Battery Socket Remove the old Lithium battery and insert the new one into the socket.

  • Page 123: Figure 4-13 Installing The Cpu Card

    ISSUE 4.1 (R5.1) SL1100 Reinstall the CPU card into the 084M-B1 mother board and close the CPU support bracket. CPU card CPU support 084M-B1 at 1228M KSU Figure 4-13 Installing the CPU Card 10. Replace the Main-Cover and Sub-Cover. Hardware Manual...

  • Page 124: Section 3 Main Software Upgrading

    • Prepare the CF Card (32MB, or upwards and formatting by FAT(16)), and store the new main software on the CF card by PC. (New main system software is supplied by NEC.) • Install the PZ-VM21 PCB. (if the system does not have it.) 3.3 Main Software Version Confirmation...

  • Page 125: Upgrading The Main Software

    ISSUE 4.1 (R5.1) SL1100 Press Enter Key (Navigation Key) to show the main system software version and Hardware Key Code. VERSION: 01.00 MAC: 00-60-B9-D8-DF-8E HKEY: 2810-0000-0000 Off-Hook and return to Time & Date mode. 11-10 WED 1:49PM Menu Dir VM:00 CL:00 3.4 Upgrading the Main Software...

  • Page 126: Table 4-1 Status Leds

    SL1100 ISSUE 4.1 (R5.1) Insert the CF card (with the new main system software loaded) to the CF slot on PZ-VM21 daughter board. (PZ-VM21 should be temporary installed if not already fitted.) CPU card CF Slot (CN2) PZ-VM21 PCB CF card...

  • Page 127: Figure 4-19 Removing The Cf Card

    ISSUE 4.1 (R5.1) SL1100 10. Turn the power off and remove the CF card from the CF slot on PZ-VM21. CPU card CF Slot (CN2) CF card PZ-VM21 PCB Figure 4-19 Removing the CF card 11. Replace the Main-Cover and Sub-Cover.

  • Page 128: Section 4 Led Indications

    SL1100 ISSUE 4.1 (R5.1) 4 LED INDICATIONS ECTION The LEDs on the CPU indicate the following: • RUN (D1) = The CPU is operating (Blue) • D2, and D3 = Alarms (Red) • D4 = Flash access indication (Red) • D5 = Boot status (Red) •...

  • Page 129: Section 1 System Capacity

    Specifications 1 SYSTEM CAPACITY ECTION Table 5-1 System Capacity Items 1 KSU (1228) Description Note Expansion Slot System Maximum Port 1KSU: 084M+PRI+080E+4COIDBx2 Trunk Port Max. 1KSU: PRIx1+4COIDB/BRIx2 Trunk Port Analogue 1KSU: 4COIDBx3 on 084M/080E/008E/ Trunks (COT) 000E BRI (T-Point) 1KSU: 2BRIx3 on 084M/080E/008E/ 000E PRI (30B) Max.
  • Page 130 SL1100 ISSUE 4.1 (R5.1) Items 1 KSU (1228) Description Note V.34 Modem 1 circuit on PZ-VM21 Conference Circuits 32 (Max. 16 parties per Confer- ence) For 1228M KSU (DSP on CPU) DSP Resource When PZ-VM21 is installed DSP Sender *1. Service Tone receiver, DTMF receiver, Caller ID sender / receiver, MF receiver, MFC receiver *2.

  • Page 131: Section 2 System Specifications

    ISSUE 4.1 (R5.1) SL1100 2 SYSTEM SPECIFICATIONS ECTION 2.1 General Precautions • Never attempt to insert wires, pins, etc. into the vents or other holes of the equipment. • Do not use benzene, thinner, or the like, or any abrasive powder to clean the equipment. Wipe it with a soft cloth.

  • Page 132: Electrical Specifications (Ksu)

    SL1100 ISSUE 4.1 (R5.1) 110VAC 120VAC 220VAC 230VAC 240VAC Frequency 47 Hz - 63 Hz (Rated Frequency: 50/60 Hz) Phase and Wire Single Phase, 2 Line + PE Type Ground Requirement No.14 AWG Copper Wire Feeding Voltage SLT: 20 mA/-27 V...

  • Page 133: Ip Terminal Power Chart

    ISSUE 4.1 (R5.1) SL1100 2540 Busy-Hour Call Attempts (BHCA) is based on a Full Capacity. 2.9 IP Terminal Power Chart Table 5-5 IP Terminal Power Chart Label Indication (Maximum Current with All Op- IEEE Note tions) IP Terminal 802.3af Class...

  • Page 134: Optional Unit Mechanical Specifications

    SL1100 ISSUE 4.1 (R5.1) 2.13 Optional Unit Mechanical Specifications Table 5-8 Optional Unit Mechanical Specifications Unit Width Depth Height Weight Note IP4[ ]-MEMDB-C1 67.5 mm 32 mm 2 mm 0.01 kg (2.66 in) (1.26 in) (0.08 in) (0.3 oz) IP4WW-VOIPDB-C1...

  • Page 135: Bgm/Exmoh Source Input Specifications

    ISSUE 4.1 (R5.1) SL1100 Item Specification Output Level Nominal 250 mV (-10 dBm) Maximum Output 400 mV RMS 2.17 BGM/ExMOH Source Input Specifications Table 5-12 BGM/External MOH Source Input Specifications Item Specification Output Impedance 600 Ω @ 1 kHz Input Level...

  • Page 136: Cable Requirements

    SL1100 ISSUE 4.1 (R5.1) 2.21 Cable Requirements Table 5-15 Cable Requirements Device Cable Type Cable Run Length Multiline Telephone 24 AWG (Φ0.5 mm) 300 m (984.3 ft) Multiline IP Telephone CAT5 Straight Cable 100 m (328.1 ft) DSS Console 24 AWG (Φ0.5 mm) 300 m (984.3 ft)
  • Page 137 ISSUE 4.1 (R5.1) SL1100 MEMO Hardware Manual...
  • Page 138 Hardware Manual NEC Corporation ISSUE 4.1 (R5.1)

This manual is also suitable for:

Sl1100 tdm basic kitIp4at-008e-b1Ip4at-1228m-b ksuIp4ww-000e-b1Ip4ww-4coidb-b1Ip4ww-2bridb-c1 ... Show all

Table of Contents