Page 1: Administrator Guide
KX-HDV430 KX-HDV330/ KX-HDV430 Thank you for purchasing this Panasonic product. Please read this manual carefully before using this product and save this manual for future use. In this manual, the suffix of each model number is omitted unless necessary. Document Version: 2017-07...
Page 2: Related Documentation
Briefly describes basic information about the installation of the unit. Operating Instructions Describes information about the installation and operation of the unit. Manuals and supporting information are provided on the Panasonic Web site at: https://panasonic.net/cns/pcc/support/sipphone/ Technical Support When technical support is required, contact your phone system dealer/service provider.
Page 3: Table Of Contents
Table of Contents Table of Contents 1 Initial Setup ..................... 9 Setup ..........................10 1.1.1 Factory Defaults ......................10 1.1.2 Language Selection for the Unit ................... 10 1.1.3 Basic Network Setup ....................10 1.1.4 Overview of Programming .................... 15 1.1.5 Phone User Interface Programming ................
Page 4 End Day and Time of DST (End Day and Time of Summer Time) ......106 4.4.5 Advanced Settings ...................... 108 4.4.5.1 Soft Key during IDLE Status (For KX-HDV130/KX-HDV230) ........108 4.4.5.2 IP Phone ........................109 4.4.6 Import Display File (For KX-HDV330/KX-HDV430) ............ 112 4.4.6.1...
Page 5 Dial Plan ........................141 4.6.3 Hotline Settings ......................142 4.6.3.1 Hotline ........................142 4.6.4 Program Key (No. 1–2) (For KX-HDV130) ..............143 4.6.5 Flexible Key Settings (No. 1–24) (For KX-HDV230/KX-HDV330/KX-HDV430) ..144 4.6.5.1 Flexible Key Settings ....................144 4.6.6 Tone Settings ......................146 4.6.6.1...
Page 6 Table of Contents 5 Configuration File Programming ............163 Configuration File Parameter List ................164 General Information on the Configuration Files ............186 5.2.1 Configuration File Parameters ..................186 5.2.2 Characters Available for String Values ............... 187 System Settings ......................188 5.3.1 System Settings ......................
Page 7 BroadCloud (Presence) Function Settings ..............376 7 Firmware Update ................379 Firmware Server Setup ....................380 Firmware Update Settings ..................380 Executing Firmware Update ..................380 Upgrade Firmware (For KX-HDV130/KX-HDV230) ............ 382 8 Troubleshooting ................. 383 Troubleshooting ......................384 Document Version: 2017-07 Administrator Guide...
Page 8 Table of Contents Administrator Guide Document Version: 2017-07...
Page 9: Initial Setup
Section 1 Initial Setup This section provides an overview of the setup procedures for the unit. Document Version: 2017-07 Administrator Guide...
Page 10: Setup
(→ see 4 Web User Interface Programming). You can select the language for the Web user interface. Note • To select the display language for the unit, refer to the Operating Instructions on the Panasonic Web site (→ see Introduction). • To select the display language for the Web user interface, see 4.4.1 Language Settings.
Page 11 The following procedures explain how to change the network settings via the unit. For details about the individual network settings that can be configured via the unit, refer to the Operating Instructions on the Panasonic Web site (→ see Introduction). Document Version: 2017-07...
Page 12 For details about the individual network settings that can be configured via the unit, refer to the Operating Instructions on the Panasonic Web site (→ see Introduction). For details about configuring network settings via the Web user interface, see 4.3.1 Basic Network Settings.
Page 13 Select Manual to enter the addresses for DNS1 (primary DNS server) and, if necessary, DNS2 (secondary DNS server) manually, and then tap "OK". To configure network settings manually KX-HDV130/KX-HDV230 [In standby mode] [ ]/[ ]: "System Settings" → [ ]/[ ]: "Network Settings" →...
Page 14 Select Manual to enter the addresses for DNS1 (primary DNS server) and, if necessary, DNS2 (secondary DNS server) manually, and then tap "OK". To configure network settings automatically using RA KX-HDV130/KX-HDV230 [In standby mode] [ ]/[ ]: "System Settings" →...
Page 15: Overview Of Programming
1.1.4 Overview of Programming [ ]/[ ]: "System Settings" → [ ]/[ ]: "Network Settings" → [ ]/[ ]: "IPv6 Settings" → [ ]/[ ]: "Static" → Enter the IP address, Prefix (for IPv6), Default Gateway, DNS1 (primary DNS server), and, if necessary, DNS2 (secondary DNS server), and then press KX-HDV330/KX-HDV430 [In standby mode]...
Page 16: Phone User Interface Programming
You can change the language used on the LCD. Because the language settings for the LCD of the unit are not synchronized, you must set the languages individually for the unit. For details about changing the setting, refer to the Operating Instructions on the Panasonic Web site (→ see Introduction).
Page 17: Password For Web User Interface Programming
Language (recommended) English Opening/Closing the Web Port To access the Web user interface, you must open the unit’s Web port beforehand. For details, refer to the Operating Instructions on the Panasonic Web site (→ see Introduction). Document Version: 2017-07 Administrator Guide...
Page 18 1.1.6 Web User Interface Programming Configuring Settings from the Unit KX-HDV130/KX-HDV230 To open the unit’s Web port [In standby mode] [ ]/[ ]: "Basic Settings" → [ ]/[ ]: "Other Option" → [ ]/[ ]: "Embedded Web" → [ ]/[ ]: "On" for "Embedded Web" →...
Page 19 1.1.6 Web User Interface Programming Note The "Embedded Web" settings can also be configured with the following procedure. When the unit is in standby mode, → "System Settings" → "Network Settings" → "Embedded Web" Configuring Settings from the Web User Interface To close the unit’s Web port In the Web user interface, click [Web Port Close].
Page 20: Accessing The Web User Interface
Note • To determine the unit’s IP address, perform the following operations on the unit: KX-HDV130/KX-HDV230 [ ]/[ ]: "System Settings" → [ ]/[ ]: "Status" → [ ]/[ ]: "IPv4 Settings"/"IPv6 Settings" → [ ]/[ ]: "IP Address". (IPv6 only)
Page 21: Controls On The Window
1.1.6 Web User Interface Programming password, and then perform authentication again with the new password to log in to the Web user interface. • The default ID for the Administrator account is "admin", and the default password is "adminpass". The ID cannot be changed from the Web user interface, but it can be changed through configuration file programming.
Page 22: Entering Characters
1.1.6 Web User Interface Programming Menu The menu displays the sub-categories of the selected tab. Configuration Screen Clicking a menu displays the corresponding configuration screen, which contains the actual settings, grouped into sections. For details, see 4.2 Status to 4.7.6 Restart. Buttons The following standard buttons are displayed in the Web user interface: Button...
Page 23 1.1.6 Web User Interface Programming – You can enter the IP address using dotted-decimal notation (i.e., "n.n.n.n" where n=0–255). – With IPv6, the IP address is enclosed in square brackets ("[" and "]"). Example: http://[2001:db8:1f70::999:de8:7648:6e8]/ • Display Name field (→ see [Display Name] in 4.6.2.1 Call Features) –...
Page 24: Firmware Update
1.2 Firmware Update Result Message Description Applicable Screens No Data The operation failed because: 4.6.7 Import Phonebook • The imported phonebook file contains no valid phonebook entries. • 4.6.8 Export Phonebook No phonebook entry is registered in the export source the unit. "Failed (Transfer Failure)"...
Page 25: General Information On Provisioning
Section 2 General Information on Provisioning This section provides an overview of the configuration file programming procedures for the unit, including pre- provisioning and provisioning. Document Version: 2017-07 Administrator Guide...
Page 26: Pre-Provisioning
If the URL contains {mac}, it will be replaced with the device’s MAC address in lowercase letters. Example: {mac} → 0080f0C571eb {MODEL} If the URL contains {MODEL}, it will be replaced with the device’s model name. Example: {MODEL} → KX-HDV130 Administrator Guide Document Version: 2017-07...
Page 27: Obtaining A Provisioning Server Address Via Sip Pnp
2.1.4 Obtaining a Provisioning Server Address via SIP PnP Macro Format {XXXX} Macro Expansion {fwver} If the URL contains {fwver}, it will be replaced with the device’s firmware version. Example: {fwver} → 01.000 Note • Macros distinguish between uppercase and lowercase letters. •...
Page 28: Obtaining A Provisioning Server Address From Dhcp Options
2.1.5 Obtaining a Provisioning Server Address from DHCP Options CFG_MASTER_FILE_PATH Provisioning server URL formats Format: <scheme>://<user>:<password>@<host>:<port>/<url-path>/<file name> <scheme> Mandatory Protocol (TFTP/FTP/HTTP/HTTPS) <user> Optional User name <password> Optional Password <host> Mandatory IP Address or Domain <port> Optional Port number <url-path> Optional Full path of the resource <file name>...
Page 29 2.1.5 Obtaining a Provisioning Server Address from DHCP Options A. SIP Phone B. DHCP Server C. Pre-provisioning Server D. KX-HDVx30.cfg DHCP DISCOVER DHCP OFFER DHCP REQUEST DHCP ACK TFTP {MODEL}.cfg 200OK Obtain provisioning server information CFG_STANDARD_FILE_PATH CFG_PRODUCT_FILE_PATH CFG_MASTER_FILE_PATH Format for pre-provisioning files obtained from DHCP option 67 Format: <path>/<file name>...
Page 30 2.1.5 Obtaining a Provisioning Server Address from DHCP Options Format for pre-provisioning server address obtained from DHCP options 159 and 160 Format: <scheme>://<user>:<password>@<host>:<port>/<path> <scheme> Mandatory Protocol (TFTP/FTP/HTTP/HTTPS) <user> Optional User name <password> Optional Password <host> Mandatory IP Address or Domain <port>...
Page 31 2.1.5 Obtaining a Provisioning Server Address from DHCP Options DHCPv6 In a DHCPv6 environment, the phone will transmit a DHCPv6 REQUEST message for DHCP option 17, receive a DHCPv6 REPLY message, obtain a pre-provisioning server address and obtain a provisioning server address from the pre-provisioning server. Note •...
Page 32: Provisioning
IP addresses of the DNS and NTP (Network Time Protocol) servers managed by your phone system dealer/service provider. This configuration file is used by all the units. Example of the configuration file’s URL: http://prov.example.com/Panasonic/ConfigCommon.cfg Administrator Guide Document Version: 2017-07...
Page 33: Downloading Configuration Files
Example of the configuration file’s URL: http://prov.example.com/Panasonic/Config{MODEL}.cfg Note • When a unit requests the configuration file, "{MODEL}" is replaced by the model name of the unit.
Page 34 Confirm that the provisioning server’s IP address/FQDN and directory are correct, and store the configuration files in the directory (e.g., http://provisioning.example.com/Panasonic/Config_Sample.cfg). Enter the IP address of the unit into the PC’s Web browser (→ see 1.1.6.3 Before Accessing the Web User Interface).
Page 35 2.2.4 Downloading Configuration Files Download Timing Explanation At regular intervals of time The configuration files are downloaded at specified intervals of time, set in minutes. In the example below, the unit has been programmed to download configuration files from the provisioning server every 3 days (4320 minutes).
Page 36 2.2.4 Downloading Configuration Files Download Timing Explanation The configuration files are downloaded periodically under the following conditions: • In the configuration file, add the line, CFG_CYCLIC="Y". – Set an interval (minutes) by specifying "CFG_CYCLIC_INTVL". • In the Web user interface: –...
Page 37 2.2.4 Downloading Configuration Files Download Timing Explanation At a specified time each day After the unit is powered on, it will download configuration files once per day at the specified time. CFG_RESYNC_TIME="02:00" SIP Phone Provisioning Server power on at 12:00 02:00 02:00 : Check...
Page 38: Provisioning Server Setting Example
Panasonic/Config{MAC}.cfg" • CFG_MASTER_FILE_PATH="http://prov.example.com/ Panasonic/ConfigCommon.cfg" Directory on the provisioning Create the "Panasonic" directory just under the HTTP root directory of server containing the the provisioning server. configuration files File name of configuration Store the following configuration files in the "Panasonic" directory.
Page 39: Encryption
2.2.6 Encryption The unit with the MAC address 0080F0222222 accesses the following URLs: http://prov.example.com/Panasonic/ConfigCommon.cfg http://prov.example.com/Panasonic/Config0080F0222222.cfg Example Provisioning Direction from the Server The following figure shows an example NOTIFY message from the server, directing the units to perform provisioning. The text "check-sync" is specified for "CFG_RESYNC_FROM_SIP".
Page 40: Priority Of Setting Methods
2.3 Priority of Setting Methods • It is recommended that you encrypt the data in order to keep the communication secure when transferring configuration files. However, if you are using the units within a secure environment, such as within an intranet, it is not necessary to encrypt the data.
Page 41: Configuration File Specifications
To prevent the designated character sequence being altered by chance, it is recommended that the configuration file starts with the comment line shown below: # Panasonic SIP Phone Standard Format File # DO NOT CHANGE THIS LINE! • Configuration files must end with an empty line.
Page 42 2.4 Configuration File Specifications "VM_NUMBER_1": for line 1, "VM_NUMBER_2": for line 2 (For KX-HDV130) , ..., "VM_NUMBER_6": for line 6 (For KX-HDV230) , ..., "VM_NUMBER_12": for line 12 (For KX-HDV330) , ..., "VM_NUMBER_16": for line 16 (For KX-HDV430) Note •...
Page 43: Configuration File Examples
If an error occurs when attempting to set the IP Mode to IPv6, see To configure IP Mode (IPv4, IPv6, IPv4&IPv6) in Configuring the Network Settings of the Unit. 2.5 Configuration File Examples The following examples of configuration files are provided on the Panasonic Web site (→ see Introduction). • Simplified Example of the Configuration File •...
Page 44: Example With Incorrect Descriptions
The following listing shows an example of a configuration file that contains incorrect formatting: An improper description is entered in the first line. A configuration file must start with the designated character sequence "# Panasonic SIP Phone Standard Format File #". Comment lines start in the middle of the lines.
Page 45: Phone User Interface Programming
Section 3 Phone User Interface Programming This section explains how to configure the unit by entering direct commands through the phone user interface. Document Version: 2017-07 Administrator Guide...
Page 46: Phone User Interface Programming
3.1 Phone User Interface Programming 3.1 Phone User Interface Programming This section provides information about the features that can be configured directly from the unit. 3.1.1 Configuring the Network Settings of the Unit You can configure the Network Settings directly from the unit. (→...
Page 47: Web User Interface Programming
Section 4 Web User Interface Programming This section provides information about the settings available in the Web user interface. Document Version: 2017-07 Administrator Guide...
Page 48: Web User Interface Setting List
4.1 Web User Interface Setting List 4.1 Web User Interface Setting List The following tables show all the settings that you can configure from the Web user interface and the access levels. For details about each setting, see the reference pages listed. For details about setting up Web user interface programming, see 1.1.6 Web User Interface Programming.
Page 49 4.1 Web User Interface Setting List Access Level Menu Item Section Title Setting Ref. VoIP Status VoIP Status Line No. ü ü page 66 Phone Number ü ü page 66 VoIP Status ü ü page 66 The access levels are abbreviated as follows: U: User;...
Page 50 4.1 Web User Interface Setting List Access Level Menu Item Section Title Setting Ref. VLAN Enable VLAN ü page 74 IP Phone VLAN ID ü page 74 IP Phone Priority ü page 74 PC VLAN ID page 75 ü PC Priority ü...
Page 51 4.1 Web User Interface Setting List Access Level Menu Item Section Title Setting Ref. Enable DNS SRV lookup ü page 82 Xtended Service Xtended Service Enable Xtended Service ü page 83 Settings Server Address ü page 83 Port page 83 ü...
Page 52 ü page 91 Enable FF Key ü page 91 Shortcut Key Settings Soft Key A (Left) ü page 91 (For KX-HDV130/ KX-HDV230) Soft Key B (Center) ü page 91 Soft Key C (Right) page 92 ü XML Phonebook LDAP URL ü...
Page 53 Soft Key during IDLE Soft Key A (Left) ü page 108 Settings Status (For Soft Key B (Center) page 109 ü KX-HDV130/ KX-HDV230) Soft Key C (Right) ü page 109 IP Phone Enable Admin Ability ü page 109 Enable IP Phone Lock ü...
Page 54 4.1 Web User Interface Setting List Access Level Menu Item Section Title Setting Ref. - LED ü page 110 Voice Message Notification －－－ - Message ü page 110 - LED page 111 ü - Alarm ü page 111 Network Camera Notification －...
Page 55 4.1 Web User Interface Setting List Access Level Menu Item Section Title Setting Ref. Registrar Server Address ü page 116 Registrar Server Port ü page 117 Proxy Server Address ü page 117 Proxy Server Port page 117 ü Presence Server Address ü...
Page 56 4.1 Web User Interface Setting List Access Level Menu Item Section Title Setting Ref. Telephone-event Payload ü page 124 Type Voice Quality Report Server Address ü page 124 Port page 125 ü Enable PUBLISH ü page 125 Alert Report Trigger ü...
Page 57 4.1 Web User Interface Setting List U: User; A: Administrator A check mark indicates that the setting is available for that access level. This setting can also be configured through configuration file programming. Telephone Access Level Menu Item Section Title Setting Ref.
Page 58 ü page 142 Hotline Number ü ü page 143 Hotline Delay ü page 143 Program Key Program Key No. 1-2 – – – (For KX-HDV130) Type ü ü page 143 Parameter page 144 ü ü Administrator Guide Document Version: 2017-07...
Page 59 4.1 Web User Interface Setting List Access Level Menu Item Section Title Setting Ref. Flexible Key Flexible Key Settings No. 1–24 — — — Settings (For KX-HDV230/ KX-HDV330/ KX-HDV430) Type ü ü page 144 Parameter ü ü page 145 Label Name ü...
Page 60 Firmware Version (For ü page 160 KX-HDV330/KX-HDV430) Upgrade Upgrade Firmware Firmware File URL (For ü page 160 Firmware (For KX-HDV130) KX-HDV130/ File Name (For KX-HDV230) KX-HDV230) Export Logging Export Logging File Logging File Type ü page 161 File Reset to Defaults...
Page 61: Status
4.2 Status Access Level Menu Item Section Title Setting Ref. Restart Restart Click [Restart] to proceed. ü page 162 Restarting will take a few moments. The access levels are abbreviated as follows: U: User; A: Administrator A check mark indicates that the setting is available for that access level. This setting can also be configured through configuration file programming.
Page 62: Network Status
Firmware Version Description Indicates the version of the firmware that is currently installed on the unit (reference only). Value Range Firmware version ("nn.nnn" [n=0–9]) (For KX-HDV130/ KX-HDV330/KX-HDV430) Bank1 (Bank2): Firmware version ("nn.nnn" [n=0–9]) (For KX-HDV230) 4.2.2 Network Status This screen allows you to view the current network information of the unit, such as the MAC address, IP address, Ethernet port status, etc.
Page 63: Ipv4
4.2.2 Network Status • Value Range IPv4 • IPv6 • IPv4&IPv6 4.2.2.2 IPv4 Connection Mode Description Indicates whether the IP address of the unit is assigned automatically (DHCP) or manually (static) (reference only). Value Range • DHCP • Static IP Address Description Indicates the currently assigned IP address of the unit (reference only).
Page 64: Ipv6
4.2.2 Network Status DNS2 Description Indicates the specified IP address of the secondary DNS server (reference only). Note • If the secondary DNS server address is not specified, this field will be left blank. Value Range IP address of the secondary DNS server 4.2.2.3 IPv6 Connection Mode Description...
Page 65: Vlan
4.2.3 VoIP Status DNS2 Description Indicates the specified IP address of the secondary DNS server (reference only). Note • If the secondary DNS server address is not specified, this field will be left blank. Value Range IP address of the secondary DNS server 4.2.2.4 VLAN Setting Mode Description...
Page 66: Voip Status
4.3 Network 4.2.3.1 VoIP Status Line No.(1–n) Description Indicates the line number to which a phone number is assigned (reference only). Value Range Line 1–Line n The number of lines available varies depending on the phone being used. Phone Number Description Indicates the currently assigned phone numbers (reference only).
Page 67: Basic Network Settings
4.3.1 Basic Network Settings 4.3.1 Basic Network Settings This screen allows you to change basic network settings such as whether to use a DHCP server, and the IP address of the unit. Note • Changes to the settings on this screen are applied when the message "Complete" appears after clicking [Save].
Page 68: Subnet Mask
4.3.1 Basic Network Settings • Value Range DHCP • Static Default Value DHCP Configuration File Reference CONNECTION_TYPE DHCP Host Name Description Specifies the host name to option12 in DHCPv4 or option15 in DHCPv6. Note • This setting is available only when [Connection Mode] is set to [DHCP].
Page 69: Ipv6
4.3.1 Basic Network Settings Default Gateway Description Specifies the default gateway for IPv4. Note • This setting is available only when [Connection Mode] is set to [Static]. Value Range Max. 15 characters n.n.n.n [n=0–255] Default Value Not stored. Configuration File Reference STATIC_GATEWAY Auto DNS via DHCP Description...
Page 70: Default Gateway
4.3.1 Basic Network Settings • Value Range DHCP • Static • Stateless Autoconfiguration Default Value DHCP Configuration File Reference CONNECTION_TYPE_IPV6 IP Address Description Specifies the IP address for IPv6. Note • This setting is available only when [Connection Mode] is set to [Static].
Page 71: Ethernet Port Settings
4.3.2 Ethernet Port Settings Auto DNS via DHCP Description Selects whether to enable or disable the DNS server obtained by DHCPv6. Note • This setting is available only when [Connection Mode] is set to [DHCP]. Value Range • Yes: Use DNS obtained by DHCPv6 •...
Page 72: Link Speed/Duplex Mode
4.3.2 Ethernet Port Settings 4.3.2.1 Link Speed/Duplex Mode LAN Port Description Selects the connection mode (link speed and duplex mode) of the LAN port. Value Range • Auto Negotiation • 100Mbps/Full Duplex • 100Mbps/Half Duplex • 10Mbps/Full Duplex • 10Mbps/Half Duplex Default Value Auto Negotiation Configuration File Reference...
Page 73: Lldp
4.3.2 Ethernet Port Settings 4.3.2.2 LLDP Enable LLDP Description Selects whether to enable or disable the LLDP-MED feature. Note • You should specify "Yes" for only one of "Enable LLDP", or "Enable VLAN". • If "Yes" is specified for two or more of the parameters above, the settings are prioritized as follows: "Enable VLAN"...
Page 74: Vlan
4.3.2 Ethernet Port Settings • Value Range • Default Value Configuration File Reference CDP_ENABLE Packet Interval Description Specifies the interval, in seconds, between sending CDP frames. Value Range 1-3600 Default Value Configuration File Reference CDP_INTERVAL 4.3.2.4 VLAN Enable VLAN Description Selects whether to use the VLAN feature to perform VoIP communication securely.
Page 75: Http Client Settings
4.3.3 HTTP Client Settings PC VLAN ID Description Specifies the VLAN ID for the PC. Value Range 0–4094 Default Value Configuration File Reference VLAN_ID_PC PC Priority Description Selects the priority for the PC. Value Range 0–7 Default Value Configuration File Reference VLAN_PRI_PC 4.3.3 HTTP Client Settings This screen allows you to change the HTTP client settings for the unit in order to access the HTTP server of...
Page 76: Http User Agent
4.3.3 HTTP Client Settings • Value Range HTTP/1.0 • HTTP/1.1 Note • For this unit, it is strongly recommended that you select [HTTP/ 1.0]. However, if the HTTP server does not function well with HTTP/1.0, try changing the setting [HTTP/1.1]. Default Value HTTP/1.0 Configuration File Reference...
Page 77: Proxy Server
4.3.4 STUN Settings 4.3.3.2 Proxy Server Enable Proxy Description Selects whether to enable or disable the HTTP proxy feature. Value Range • • Default Value Configuration File Reference HTTP_PROXY_ENABLE Proxy Server Address Description Specifies the IP address or FQDN of the proxy server. Value Range Max.
Page 78: Multicast Paging Settings
4.3.5 Multicast Paging Settings Value Range Max. 256 characters Default Value Not stored. Configuration File Reference STUN_SERV_ADDR Port Description Specifies the port number of the STUN server for the CPE to send Binding Requests. Value Range 1–65535 Default Value 3478 Configuration File Reference STUN_SERV_PORT Binding Interval...
Page 79: Multicast Paging
4.3.5 Multicast Paging Settings 4.3.5.1 Multicast Paging IPv4 Address (Group 1–5) Description Specifies the address for multi-cast paging for each channel group. {Priority: Group 5 > Group 4 > Group 3, Group2, Group1 (depending on the configuration)} Value Range 224.0.0.0–239.255.255.255 Default Value Not stored.
Page 80: Ldap Settings
4.3.6 LDAP Settings • Value Range • Default Value Configuration File Reference MPAGE_SEND_ENABLEm 4.3.6 LDAP Settings This screen allows you to change the LDAP Settings. 4.3.6.1 LDAP Enable LDAP Description Selects whether to enable or disable the LDAP service. Value Range •...
Page 81 4.3.6 LDAP Settings Value Range Max. 256 characters Note • The LDAP server address should start with "ldap://" or "ldaps://". Default Value Not stored. Configuration File Reference LDAP_SERVER Port Description Specifies the port of server. Value Range 1–65535 Default Value Configuration File Reference LDAP_SERVER_PORT User ID...
Page 82: Xtended Service Settings
4.3.7 Xtended Service Settings Number Filter Description Specifies the number filter which is the search criteria for number look Value Range Max. 256 characters Default Value (|(telephoneNumber=%)(mobile =%)(homePhone =%)) Configuration File Reference LDAP_NUMB_FILTER Name Attributes Description Specifies the name attributes of each record which are to be returned in the LDAP search result.
Page 83: Xtended Service
4.3.7 Xtended Service Settings 4.3.7.1 Xtended Service Enable Xtended Service Description Selects whether to enable or disable the Xsi service. Value Range • • Default Value Configuration File Reference XSI_ENABLE Server Address Description Specifies the IP address or FQDN of the Xsi server. Value Range Max.
Page 84: Xtended Service Settings [Line 1]-[Line N]
Line n: The number of lines available varies depending on the phone being used. Note This menu appears for KX-HDV330/KX-HDV430. For KX-HDV130/KX-HDV230, this Line 1 - Line n setting dialog appears on previous Xtended Service Settings menu. User ID Description Specifies the authentication ID required to access the Xsi server.
Page 85 4.3.7 Xtended Service Settings Value Range Max. 128 characters Default Value Not stored. Configuration File Reference XSI_PASSWORD_n Enable Phonebook Description Selects whether to enable or disable the Xsi phonebook service. Value Range • • Default Value Configuration File Reference XSI_PHONEBOOK_ENABLE_n Phonebook Type Description Selects the type of Xsi phonebook.
Page 86 4.3.7 Xtended Service Settings • Value Range • Note • This setting is available only when "BSD_MULTI_TYPE_ENABLE" is set to "Y". Default Value Configuration File Reference BSD_GROUPCOM_ENABLE_n Enterprise Description Specifies whether to enable or disable the "Enterprise" type for Xsi phonebooks.
Page 87: Uc Settings
4.3.8 UC Settings Configuration File Reference BSD_PERSONAL_ENABLE_n Enable Call Log Description Selects whether to enable or disable the Xsi call log service. Value Range • • Default Value Configuration File Reference XSI_CALLLOG_ENABLE_n Enable Visual Voice Mail (For KX-HDV330/KX-HDV430) Description Selects whether to enable or disable the Visual Voice Mail feature of the selected line.
Page 88: Xml Application Settings
4.3.9 XML Application Settings • Value Range • Default Value Configuration File Reference UC_ENABLE Server Address Description Specifies the IP address or FQDN of the XMPP server. Value Range Max. 256 characters Default Value Not stored. Configuration File Reference XMPP_SERVER Local XMPP Port Description Specifies the local XMPP port.
Page 89: Xml Application
4.3.9 XML Application Settings 4.3.9.1 XML Application Enable XMLAPP Description Selects whether to enable or disable the XML application feature. • Value Range • Default Value Configuration File Reference XMLAPP_ENABLE User ID Description Specifies the authentication ID required to access the XML application server.
Page 90 4.3.9 XML Application Settings Local XML Port Description Specifies the local HTTP port for XML application. Value Range 1–65535 Default Value 6666 Configuration File Reference XML_HTTPD_PORT Bootup URL Description Specifies the URL that is accessed when the unit starts up, to check for XML data.
Page 91: Shortcut Key Settings (For Kx-Hdv130/Kx-Hdv230)
Value Range • Default Value Configuration File Reference XMLAPP_FFKEY_ENABLE 4.3.9.2 Shortcut Key Settings (For KX-HDV130/KX-HDV230) Soft Key A (Left) Description Specifies whether to enable the XML application or operate the telephone normally, when the corresponding button is pressed during standby mode.
Page 92: Xml Phonebook
Value Range • • Default Value Configuration File Reference XML_INITIATE_KEY_SOFT3 (For KX-HDV130/KX-HDV230) 4.3.9.3 XML Phonebook LDAP URL Description Specifies the URL that is accessed when the phonebook is accessed, to check for XML data. Value Range Max.
Page 93: Acd Settings [Line 1]-[Line N]
4.3.10 ACD Settings [Line 1]–[Line n] 4.3.10 ACD Settings [Line 1]–[Line n] Note Line n: The number of lines available varies depending on the phone being used. Enable ACD Description Selects whether to enable the ACD. Value Range • • Default Value Configuration File Reference ACD_ENABLE_n...
Page 94: Customer Originated Trace
4.3.11 Call Center Settings [Line 1]–[Line n] Enable Call Center Description Selects whether to add menu items for Call Center. Value Range • • Default Value Configuration File Reference CALL_CENTER_ENABLE_n Disposition Code Description Selects whether to enable the Disposition Code. Value Range •...
Page 95 4.3.11 Call Center Settings [Line 1]–[Line n] Hoteling Event Description Selects whether to enable the Hoteling Event. • Value Range • Default Value Configuration File Reference CC_HOTELING_EVENT_n - User ID Description Specifies the authentication ID required to access the Hoteling service.
Page 96: Twamp Settings
4.3.12 TWAMP Settings 4.3.12 TWAMP Settings Enable TWAMP Description Selects whether to enable the TWAMP server function. Value Range • • Default Value Configuration File Reference TWAMP_ENABLE Control Port Description Specifies the port for the TWAMP control session. Value Range 1-65535 Default Value Configuration File Reference...
Page 97: System
4.4 System Value Range 1-65535 Default Value 9000 Configuration File Reference TWAMP_TEST_PORT Wait Time for Control Description Specifies the time, in seconds, for the TWAMP server to wait for incoming packets for maintaining the session. Value Range 1-65535 Default Value Configuration File Reference TWAMP_SERVER_WAIT_TIME Wait Time for Reflector...
Page 98: Selectable Language
4.4.1 Language Settings 4.4.1.1 Selectable Language IP Phone Description Specifies the selectable language on the unit. Up to 10 languages separated by commas can be registered. (e.g., "en,es,fr,de,it,nl,pt") Administrator Guide Document Version: 2017-07...
Page 99: Web Language
4.4.1 Language Settings • Value Range en: English • es: Spanish • fr: French • de: German • it: Italian • da: Danish • nl: Dutch • sv: Swedish • fi: Finnish • el: Greek • hu: Hungarian • pt: Portuguese •...
Page 100: Language Settings
4.4.1 Language Settings • Value Range en: English • es: Spanish • fr: French • de: German • it: Italian • nl: Dutch • el: Greek • hu: Hungarian • pt: Portuguese • pl: Polish • sk: Slovakian • cs: Czech •...
Page 101: User Password Settings
4.4.2 User Password Settings Default Value Configuration File Reference WEB_LANGUAGE 4.4.2 User Password Settings This screen allows you to change the password used to authenticate the User account when logging in to the Web user interface. Note • For security reasons, the characters entered for the password are masked by special characters, which differ depending on the Web browser.
Page 102: Admin Password Settings
4.4.3 Admin Password Settings Value Range 6–64 characters (except !, ", #, $, %, &, ', (, ), @, *, +, ,, /, :, ;, <, =, >, ?, [, ], ^, `, {, |, }, ~, \ and space) Note •...
Page 103: Admin Password
4.4.4 Time Adjust Settings 4.4.3.1 Admin Password Current Password Description Specifies the current password to use to authenticate the Administrator account when logging in to the Web user interface. Value Range 6–64 characters (except !, ", #, $, %, &, ', (, ), @, *, +, ,, /, :, ;, <, =, >, ?, [, ], ^, `, {, |, }, ~, \ and space) Default Value adminpass...
Page 104: Synchronization (Synchronisation)
4.4.4 Time Adjust Settings 4.4.4.1 Synchronization (Synchronisation) Server Address Description Specifies the IP address or FQDN of NTP server. Value Range Max. 256 characters Default Value Not stored. Configuration File Reference NTP_ADDR Synchronization Interval (Synchronisation Interval) Description Specifies the interval, in seconds, between synchronizations with the NTP server.
Page 105: Daylight Saving Time (Summer Time)
4.4.4 Time Adjust Settings 4.4.4.3 Daylight Saving Time (Summer Time) Enable DST (Enable Summer Time) Description Selects whether to enable Daylight Saving Time (Summer Time). Value Range • • Default Value Configuration File Reference DST_ENABLE DST Offset (Summer Time Offset) Description Specifies the amount of time, in minutes, to change the time when "DST_ENABLE"...
Page 106: End Day And Time Of Dst (End Day And Time Of Summer Time)
4.4.4 Time Adjust Settings • Value Range First • Second • Third • Fourth • Last Default Value Second Configuration File Reference DST_START_ORDINAL_DAY Description Selects the day of the week on which DST (Summer Time) starts. Value Range • Sunday •...
Page 107 4.4.4 Time Adjust Settings • Value Range January • February • March • April • • June • July • August • September • October • November • December Default Value November Configuration File Reference DST_STOP_MONTH Day of Week Using the 2 following settings, specify on which day of the selected month DST (Summer Time) ends. For example, to specify the second Sunday, select [Second] and [Sunday].
Page 108: Advanced Settings
Configuration File Reference DST_STOP_TIME 4.4.5 Advanced Settings This screen allows you to change the Soft Key function settings. 4.4.5.1 Soft Key during IDLE Status (For KX-HDV130/KX-HDV230) Soft Key A (Left) Description Selects soft key (A) during IDLE state. Value Range •...
Page 109: Ip Phone
• Incoming Call Log • Redial • Page (Used when performing Multicast Paging) Default Value Menu Configuration File Reference IDLE_SOFT_KEY_B (For KX-HDV130/KX-HDV230) Soft Key C (Right) Description Selects soft key (C) during IDLE state. • Value Range Phonebook • Menu •...
Page 110 4.4.5 Advanced Settings Password for Unlocking Description Specifies the password for unlocking the unit. Value Range Null, 4 digits (0–9) Default Value Not stored. Configuration File Reference SYS_LOCK_PASSWORD Missed Call Notification - Message Description Selects whether to display 'Missed Calls' on the screen in standby mode.
Page 111 4.4.5 Advanced Settings Voice Message Notification - LED Description Selects whether the LED is used to indicate a new voice message. Note • This setting is available only when "NOTIFICATION_MENU_ENABLE" is set to "Y". Value Range • • Default Value Configuration File Reference NOTIFY_VOICEMAIL_LED_ENABLE Voice Message Notification - Alarm...
Page 112: Import Display File (For Kx-Hdv330/Kx-Hdv430)
4.4.6 Import Display File (For KX-HDV330/KX-HDV430) Default Value Configuration File Reference NOTIFY_NETWORKCAMERA_LED_ENABLE (For KX-HDV430) Network Camera Notification - Alarm (For KX-HDV430） Description Selects whether an alarm sound is used to indicate a Network Camera alert. Note • This setting is available only when "NOTIFICATION_MENU_ENABLE"...
Page 113: Wait Time
4.4.8 Communication Camera (For KX-HDV430) 4.4.7.1 Wait Time Wait Time Description Specifies the time, in seconds, to wait for the screen saver to display. Value Range 0, 10, 30, 60, 180, 300 (sec) [0:off] Default Value 4.4.8 Communication Camera (For KX-HDV430) This screen allows you to change the Communication Camera settings.
Page 114: Voip
4.5 VoIP Default Value Not stored. Configuration File Reference COMM_CAMERA_NUMBERx Name Description Specifies the name of each Communication Camera. Value Range Max. 24 characters Default Value Not stored. Configuration File Reference COMM_CAMERA_NAMEx Ringtone [ 1 - 32 ] Description Specifies the ringtone of each Communication Camera. Value Range 1–32 (10: doorbell) Default Value...
Page 115: Nat Identity
• If "{sipver}" is included in this parameter, it will be replaced with the SIP software version of the unit. Default Value Panasonic-{MODEL}/{fwver} ({mac}) Configuration File Reference SIP_USER_AGENT 4.5.1.2 NAT Identity Enable Rport (RFC 3581)
Page 116: Sip Settings [Line 1]-[Line N]
4.5.2 SIP Settings [Line 1]–[Line n] 4.5.2 SIP Settings [Line 1]–[Line n] Note Line n: The number of lines available varies depending on the phone being used. This screen allows you to change the SIP settings that are specific to each line. 4.5.2.1 Basic Phone Number Description...
Page 117: Registrar Server Port
4.5.2 SIP Settings [Line 1]–[Line n] Default Value Not stored. Configuration File Reference SIP_RGSTR_ADDR_n Registrar Server Port Description Specifies the port number to use for communication with the SIP registrar server. Value Range 1–65535 Default Value 5060 Configuration File Reference SIP_RGSTR_PORT_n Proxy Server Address Description...
Page 118: Advanced
4.5.2 SIP Settings [Line 1]–[Line n] Configuration File Reference SIP_OUTPROXY_ADDR_n Outbound Proxy Server Port Description Specifies the port number to use for communication with the SIP outbound proxy server. Value Range 1–65535 Default Value 5060 Configuration File Reference SIP_OUTPROXY_PORT_n Service Domain Description Specifies the domain name provided by your phone system dealer/ service provider.
Page 119: Srv Lookup Prefix For Udp
4.5.2 SIP Settings [Line 1]–[Line n] • Value Range • Note • If you select [Yes], the unit will perform a DNS SRV lookup for a SIP registrar server, SIP proxy server, SIP outbound proxy server, or SIP presence server. If you select [No], the unit will not perform a DNS SRV lookup for a SIP registrar server, SIP proxy server, SIP outbound proxy server, or SIP presence server.
Page 120: Sip Uri
5160 (for Line 11) 5170 (for Line 12) 5180 (for Line 13) 5190 (for Line 14) 5200 (for Line 15) 5210 (for Line 16) Note KX-HDV130 Line 1-2 KX-HDV230 Line 1-6 KX-HDV330 Line 1-12 KX-HDV430 Line 1-16 Configuration File Reference SIP_SRC_PORT_n SIP URI...
Page 121: Session Timer Method
4.5.2 SIP Settings [Line 1]–[Line n] • Value Range • • 1000 • 2000 • 4000 Default Value Configuration File Reference SIP_TIMER_T1_n T2 Timer Description Specifies the maximum interval, in seconds, between transmissions of SIP messages. Value Range • • •...
Page 122: Transport Protocol
4.5.2 SIP Settings [Line 1]–[Line n] Default Value INVITE Configuration File Reference SIP_SESSION_METHOD_n Enable 100rel (RFC 3262) Description Specifies whether to add the option tag 100rel to the "Supported" header of the INVITE message. Value Range • • Note • If you select [Yes], the Reliability of Provisional Responses function will be enabled.
Page 123: Voip Settings
4.5.3 VoIP Settings • Value Range • • Default Value Configuration File Reference SIP_TRANSPORT_n TLS Mode Description Select the secure SIP protocol. Value Range • SIPS • SIP-TLS Default Value SIPS Configuration File Reference SIP_TLS_MODE_n 4.5.3 VoIP Settings This screen allows you to change the VoIP settings that are common to all lines. Document Version: 2017-07 Administrator Guide...
Page 124: Rtp
4.5.3 VoIP Settings 4.5.3.1 RTP RTP Packet Time Description Selects the interval, in milliseconds, between transmissions of RTP packets. Value Range • • • • Default Value Configuration File Reference RTP_PTIME Minimum RTP Port Number Description Specifies the lowest port number that the unit will use for RTP packets.
Page 125 4.5.3 VoIP Settings Default Value Not stored. Configuration File Reference VQREPORT_COLLECTOR_ADDRESS Port Description Specifies the port of the collector server. Value Range 1–65535 Default Value 5060 Configuration File Reference VQREPORT_COLLECTOR_PORT Enable PUBLISH Description Selects the sending type of the VQ report using PUBLISH. •...
Page 126: Voip Settings [Line 1]-[Line N]
4.5.4 VoIP Settings [Line 1]–[Line n] Threshold Delay (Critical) Description Specifies the criteria (critical) to send the VQ report when a delay occurs. Value Range 0–2000 Default Value Configuration File Reference ALERT_REPORT_DELAY_CRITICAL Threshold Delay (Warning) Description Specifies the criteria (warning) to send the VQ report when a delay occurs.
Page 127: Basic
4.5.4 VoIP Settings [Line 1]–[Line n] 4.5.4.1 Basic G.722 Enable Description Selects whether to enable the G.722 codec for voice data transmission. Value Range • • Default Value Configuration File Reference CODEC_ENABLEx_n G.722 Priority Description Specifies the numerical order usage priority for the G.722 codec. Value Range 1–255 Default Value...
Page 128: Pcma Enable
4.5.4 VoIP Settings [Line 1]–[Line n] PCMA Enable Description Selects whether to enable the PCMA codec for voice data transmission. Value Range • • Default Value Configuration File Reference CODEC_ENABLEx_n PCMA Priority Description Specifies the numerical order usage priority for the PCMA codec. Value Range 1–255 Default Value...
Page 129: Advanced
4.5.4 VoIP Settings [Line 1]–[Line n] Default Value Configuration File Reference CODEC_PRIORITYx_n DTMF Type Description Selects the method for transmitting DTMF (Dual Tone Multi- Frequency) tones. Value Range • RFC2833 • Inband • SIP INFO Note • RFC2833 refers to Outband DTMF. •...
Page 130 SRTP Mode Description Selects the mode of SRTP feature. Value Range • 0: SRTP • 1: RTP/SRTP • 2: Panasonic Original • 3: SRTP/RTP Note • 0: SRTP Use only SRTP for outgoing and incoming calls. • 1: RTP/SRTP Use only RTP for outgoing calls, and RTP or SRTP for incoming calls.
Page 131: Telephone
4.6 Telephone Configuration File Reference SRTP_MIX_CONFERENCE_ENABLE_n Enable Mixed SRTP & RTP by Transfer Description Selects whether to allow call transfers between a user who is using SRTP and a user who is using RTP. • Value Range • Default Value Configuration File Reference SRTP_MIX_TRANSFER_ENABLE_n 4.6 Telephone...
Page 132: Call Control
4.6.1 Call Control 4.6.1.1 Call Control Send SUBSCRIBE to Voice Mail Server Description Selects whether to send the SUBSCRIBE request to a voice mail server. Note • Your phone system must support voice mail. Value Range • • Default Value Configuration File Reference VM_SUBSCRIBE_ENABLE Conference Server URI...
Page 133: International Call Prefix
4.6.1 Call Control Default Value Configuration File Reference MACRODIGIT_TIM Enable # Key as delimiter Description Selects whether the # key is treated as a regular dialed digit or a delimiter, when dialed as or after the second digit. Value Range •...
Page 134 Line 12 • Line 13 • Line 14 • Line 15 • Line 16 Note KX-HDV130 Line 1-2 KX-HDV230 Line 1-6 KX-HDV330 Line 1-12 KX-HDV430 Line 1-16 Default Value Line 1 Configuration File Reference DEFAULT_LINE_SELECT Call Park Number Description Specifies the call parking number.
Page 135: Directed Call Pickup
0–4 digits (0–9, *, #) Default Value Not stored. Configuration File Reference NUM_PLAN_PARK_RETRIEVING Park Retrieve Soft Key (For KX-HDV130/KX-HDV230) Description Selects whether to have soft key for the call park retrieving. Note • This feature is available only when [Enable Call Park...
Page 136: Emergency Call Phone Numbers
4.6.2 Call Control [Line 1]–[Line n] • Value Range • Default Value Configuration File Reference PRIVATE_HOLD_ENABLE 4.6.1.2 Emergency Call Phone Numbers 1–5 Description Specifies the phone numbers used for making emergency calls. A user can dial any of the specified phone numbers at any time regardless of any restrictions imposed on the unit.
Page 137: Call Features
4.6.2 Call Control [Line 1]–[Line n] 4.6.2.1 Call Features Display Name Description Specifies the name to display as the caller on the other party’s phone when you make a call. Value Range Max. 24 characters Note • You can use Unicode characters for this setting. Default Value Not stored.
Page 138: Enable Call Waiting
4.6.2 Call Control [Line 1]–[Line n] • Value Range • Default Value Configuration File Reference ANONYMOUS_CALL_ENABLE_n Enable Block Anonymous Call Description Selects whether to accept or reject the incoming call without the called party’s phone number. Value Range • • Default Value Configuration File Reference BLOCK_ANONYMOUS_CALL_ENABLE_n...
Page 139: Enable Shared Call
4.6.2 Call Control [Line 1]–[Line n] Enable Call Forwarding Busy Description Selects whether to forward incoming calls to a specified destination when the line is in use. Value Range • • Default Value Forwarding Number (Busy) Description Specifies the phone number of the destination to forward calls to when the line is in use.
Page 140 4.6.2 Call Control [Line 1]–[Line n] • Value Range • Note • If you select [Yes], the SIP server will control the line by using a shared-call signaling method. If you select [No], the SIP server will control the line by using a standard signaling method.
Page 141: Dial Plan
4.6.2 Call Control [Line 1]–[Line n] • Value Range • Default Value Configuration File Reference BS_EXECUTIVE_SETTING_ENABLE_n (For KX-HDV330/ KX-HDV430) Enable Assistant Setting (For KX-HDV330/KX-HDV430) Description Selects whether to enable the Executive-Assistant Call Filtering feature and the Executive-Assistant Divert feature of the selected line.
Page 142: Hotline Settings
4.6.3 Hotline Settings • Value Range • Note • If you select [Yes], calls will be made even if the dialed number does not match the dial formats specified in [Dial Plan] (i.e., dial plan filtering is disabled). If you select [No], calls will not be made if the dialed number does not match one of the dial formats specified in [Dial Plan] (i.e., dial plan filtering is enabled).
Page 143: Program Key (No. 1-2) (For Kx-Hdv130)
4.6.4 Program Key (No. 1–2) (For KX-HDV130) Default Value Configuration File Reference HOTLINE_ENABLE Hotline Number Description Specifies the Hot line number. Value Range Max. 32 characters Default Value Not stored. Configuration File Reference HOTLINE_NUMBER Hotline Delay Description Specifies a time after off hook for Hot line.
Page 144: Flexible Key Settings (No. 1-24) (For Kx-Hdv230/Kx-Hdv330/Kx-Hdv430)
4.6.5 Flexible Key Settings (No. 1–24) (For KX-HDV230/KX-HDV330/KX-HDV430) Default Value Not stored. Configuration File Reference FLEX_BUTTON_FACILITY_ACTx Parameter Description Specifies an optional argument associated with the specified Facility Action for the flexible button. Value Range Max. 32 characters Default Value Not stored. Configuration File Reference FLEX_BUTTON_FACILITY_ARGx 4.6.5 Flexible Key Settings (No.
Page 145 4.6.5 Flexible Key Settings (No. 1–24) (For KX-HDV230/KX-HDV330/KX-HDV430) • Value Range One Touch Dial • • Line • • Wrap Up • Line Status • Call Forward • Phonebook • Call History • Simultaneous Ring • Hoteling (Hospitality) • Transfer •...
Page 146: Tone Settings
4.6.6 Tone Settings 4.6.6 Tone Settings This screen allows you to configure the dual-tone frequencies and ringtone patterns of each tone. 4.6.6.1 Dial Tone Tone Frequencies Description Specifies the dual-tone frequencies, in hertz, of dial tones using 2 whole numbers separated by a comma. Value Range 0, 200–2000 (0: No tone) Note...
Page 147: Busy Tone
4.6.6 Tone Settings Tone Timings Description Specifies the pattern, in milliseconds, of dial tones using up to 10 whole numbers (off 1, on 1, off 2, on 2…) separated by commas. Note • The unit will not play the tone for the duration of the first value, play it for the duration of the second value, stop it for the duration of the third value, play it again for the duration of the fourth value, and so on.
Page 148: Ringing Tone
4.6.6 Tone Settings 4.6.6.3 Ringing Tone Tone Frequencies Description Specifies the dual-tone frequencies, in hertz, of ringback tones using 2 whole numbers separated by a comma. Value Range 0, 200–2000 (0: No tone) Note • If the value for this setting is "440,480", the unit will use a mixed signal of a 440 Hz tone and a 480 Hz tone.
Page 149: Reorder Tone
4.6.6 Tone Settings Tone Timings Description Specifies the pattern, in milliseconds, of stutter dial tones to notify that a voice mail is waiting, using up to 22 whole numbers (off 1, on 1, off 2, on 2…) separated by commas. Note •...
Page 150: Import Phonebook
4.6.7 Import Phonebook 4.6.7 Import Phonebook This screen allows you to import phonebook data from a PC to the specified unit. For details, see 6.1.1 Import/Export Operation. Note • If the existing phonebook data has an entry with the same name and phone number as an imported entry, the imported entry is not added as a new entry.
Page 151: Export Phonebook
4.6.8 Export Phonebook Value Range No limitation Note • There are no limitations for the field entry. However, it is recommended that paths of less than 256 characters be used: longer paths may cause longer data transfer times and result in an internal error.
Page 152: Export Phonebook
4.6.9 Video Call Settings (For KX-HDV430) 4.6.8.1 Export Phonebook Export Phonebook Click [Export] button to export the phonebook from this unit. 4.6.9 Video Call Settings (For KX-HDV430) This screen allows you to change the Video Call settings. Administrator Guide Document Version: 2017-07...
Page 153: Default Call Mode
4.6.9 Video Call Settings (For KX-HDV430) 4.6.9.1 Default Call Mode Default Call Mode Description Selects the default call type when you make a call by going off hook, etc. Value Range • Voice • Video Default Value Voice Configuration File Reference DEFAULT_CALL_MODE 4.6.9.2 Screen Mode Screen Mode...
Page 154: Send Image
4.6.9 Video Call Settings (For KX-HDV430) Default Value Normal Configuration File Reference VIDEO_SCREEN_MODE 4.6.9.3 Send Image Send Image at Start Description Selects whether the video is automatically sent when you start a video call. Value Range • • Default Value Configuration File Reference VIDEO_SEND_IMAGE_ENABLE 4.6.9.4 Rate Settings...
Page 155: Dss Console (For Kx-Hdv230/Kx-Hdv330/Kx-Hdv430)
4.6.10 DSS Console (For KX-HDV230/KX-HDV330/KX-HDV430) Configuration File Reference VIDEO_FRAME_RATE Image Size Description Selects the size for video images when you make a video call. Value Range • QCIF • QVGA • • HVGAW • Default Value HVGAW Configuration File Reference VIDEO_IMAGE_SIZE 4.6.10 DSS Console (For KX-HDV230/KX-HDV330/KX-HDV430) This screen allows you to configure various features for each DSS console key.
Page 156 4.6.10 DSS Console (For KX-HDV230/KX-HDV330/KX-HDV430) • Value Range One Touch Dial • • Line • • Wrap Up • Line Status • Call Forward • Phonebook • Call History • Simultaneous Ring • Hoteling (Hospitality) • Transfer • Blind Transfer •...
Page 157: Maintenance
4.7 Maintenance 4.7 Maintenance This section provides detailed descriptions about all the settings classified under the [Maintenance] tab. 4.7.1 Provisioning Maintenance This screen allows you to change the provisioning setup to download the configuration files from the provisioning server of your phone system. 4.7.1.1 Provisioning Maintenance Standard File URL Description...
Page 158: Cyclic Auto Resync
4.7.1 Provisioning Maintenance Default Value Not stored. Configuration File Reference CFG_PRODUCT_FILE_PATH Master File URL Description Specifies the URL of the master configuration file, which is used when all units need the same settings. Value Range Max. 384 characters Note • For details about the formats, see 2.1.3 Server Address Formats.
Page 159: Firmware Maintenance
Note • Manual firmware updates from the Web user interface (→ see 4.7.3 Upgrade Firmware (For KX-HDV130/KX-HDV230)) can be performed regardless of this setting. • Firmware updates using TR-069 can be performed regardless of this setting.
Page 160: Upgrade Firmware (For Kx-Hdv130/Kx-Hdv230)
4.7.3 Upgrade Firmware (For KX-HDV130/KX-HDV230) Value Range Max. 384 characters Note • If "{fwver}" is included in this parameter, it will be replaced with the value specified in [Firmware Version]. For details about the formats, see 2.1.3 Server Address Formats.
Page 161: Export Logging File
4.7.4 Export Logging File File Name (For KX-HDV230) Description Specifies the path of the firmware file to be imported. Value Range No limitation Note • There are no limitations for the field entry. However, it is recommended that paths of less than 256 characters be used: longer paths may cause longer data transfer times and result in an internal error.
Page 162: Reset To Defaults
4.7.5 Reset to Defaults 4.7.5 Reset to Defaults This screen allows you to reset the carrier default settings made through the Web user interface to their default values by clicking [Reset to Carrier Defaults]. After you click this button, a dialog box is displayed, asking whether you want to reset the settings.
Page 163: Configuration File Programming
Section 5 Configuration File Programming This section provides information about the configuration parameters used in the configuration files. Document Version: 2017-07 Administrator Guide...
Page 164: Configuration File Parameter List
5.1 Configuration File Parameter List 5.1 Configuration File Parameter List The following tables show all the parameters that can be programmed using configuration file programming. For details about each parameter, see the reference pages listed. For details about configuration file specifications, see 2.4 Configuration File Specifications. System Settings Parameter Name Ref.
Page 165 5.1 Configuration File Parameter List Parameter Name Ref. page 195 NOTIFY_NETWORKCAMERA_ALARM_ENABLE NOTIFICATION_ALARM_TYPE page 195 page 195 CODEC_VAD_CNG_ENABLE BOOTLOG_SERVER_URI page 196 DISPLAY_DIVERSION_ENABLE page 196 ERROR_AUTO_REBOOT_TIME page 196 HOME_DISPLAY_TYPE page 196 FUNCTION_DISPLAY_TYPE page 196 FOCUS_OPERATION_ENABLE page 197 INCOMING_DISPLAY_ENABLE page 197 DISPLAY_AUTO_CHANGE_ENABLE page 197 NOTIFY_FUNC_KEY_ENABLE page 197 NOTIFY_DSS_KEY_ENABLE...
Page 166 5.1 Configuration File Parameter List Basic Network Settings Parameter Name Ref. page 207 IP_ADDR_MODE page 207 CONNECTION_TYPE page 207 STATIC_IP_ADDRESS page 208 STATIC_SUBNET page 208 STATIC_GATEWAY page 208 USER_DNS1_ADDR page 209 USER_DNS2_ADDR page 209 DHCP_DNS_ENABLE page 209 DHCP_HOST_NAME DHCP_VENDOR_CLASS page 210 page 210 CONNECTION_TYPE_IPV6 page 210...
Page 167 5.1 Configuration File Parameter List Parameter Name Ref. page 215 CDP_INTERVAL Pre-Provisioning Settings Parameter Name Ref. SIPPNP_PROV_ENABLE page 215 OPTION66_ENABLE page 215 OPTION159_PROV_ENABLE page 215 OPTION160_PROV_ENABLE page 216 DHCPV6_OPTION17_PROV_ENABLE page 216 Provisioning Settings Parameter Name Ref. page 216 CFG_STANDARD_FILE_PATH page 216 CFG_PRODUCT_FILE_PATH page 217 CFG_MASTER_FILE_PATH...
Page 168 5.1 Configuration File Parameter List Parameter Name Ref. FWDL_RANDOM_DURATION page 222 HTTP Settings Parameter Name Ref. page 223 HTTP_VER page 223 HTTP_USER_AGENT page 223 HTTP_AUTH_ID page 224 HTTP_AUTH_PASS page 224 HTTP_PROXY_ENABLE page 224 HTTP_PROXY_ADDR page 224 HTTP_PROXY_PORT HTTP_PROXY_ID page 224 HTTP_PROXY_PASS page 225 HTTPD/WEB Settings...
Page 169 5.1 Configuration File Parameter List Parameter Name Ref. ANNEX_G_STUN_SERV_PORT page 229 ANNEX_G_STUN_USER_ID page 230 ANNEX_G_STUN_PASS page 230 ANNEX_G_STUN_MAX_KEEP_ALIVE page 230 ANNEX_G_STUN_MIN_KEEP_ALIVE page 231 UDP_CON_REQ_ADDR_NOTIFY_LIMIT page 231 DEVICE_PROVISIONING_CODE page 231 TR069_REGISTERING page 231 TR069_REGISTERED page 231 XML Settings Parameter Name Ref. page 232 XMLAPP_ENABLE page 232...
Page 170 5.1 Configuration File Parameter List Parameter Name Ref. XMLAPP_URL_FLEX_BUTTONx page 236 XMLAPP_STATUSBAR_ENABLE page 237 SYS_HOME_MENU_XML_NAMEx page 237 SYS_HOME_MENU_XML_URLx page 237 SYS_HOME_MENU_XML_ICONx page 237 XML_PHONEBOOK_URL page 238 XML_PHONEBOOK_CYCLIC_INTVL page 238 XML_CURSOR_SKIP_ENABLE page 238 XMLAPP_URL_REDIAL_KEY page 238 XMLAPP_RCV_IP_ADDRESSx page 238 XSI Settings Parameter Name Ref.
Page 171 5.1 Configuration File Parameter List XMPP (UC-ONE) Settings Parameter Name Ref. page 243 UC_ENABLE page 243 UC_USERID page 244 UC_PASSWORD page 244 XMPP_SERVER page 244 XMPP_PORT XMPP_TLS_VERIFY page 244 XMPP_ROOT_CERT_PATH page 244 XMPP_CLIENT_CERT_PATH page 245 XMPP_PKEY_PATH page 245 UC_DNSSRV_ENA page 245 UC_TCP_SRV_PREFIX page 245 UC_USERID_CASE_SENSITIVE...
Page 172 5.1 Configuration File Parameter List Parameter Name Ref. LDAP_PKEY_PATH page 250 LDAP_DISPLAY_FORMAT page 250 Call Center Settings Parameter Name Ref. page 250 CALL_CENTER_ENABLE_n page 250 ACD_ENABLE_n ACD_LOGIN_CONDITION_n page 251 ACD_LOGOUT_CONDITION_n page 251 page 251 CC_DISPOSITION_CODE_ENABLE_n page 251 CC_CUSTOMER_ORG_TRACE_ENABLE_n page 251 CC_HOTELING_EVENT_n page 252 HOTELING_USERID_n...
Page 173 5.1 Configuration File Parameter List Parameter Name Ref. page 255 MPAGE_PRIORITYm page 256 MPAGE_LABELm page 256 MPAGE_SEND_ENABLEm MPAGE_CODEC page 256 MPAGE_SP_VOL_EMERGENCY page 256 MPAGE_SP_VOL_PRIORITY page 256 MPAGE_DND_ENABLE page 257 MPAGE_FUNCKEY_ENABLE page 257 NTP Settings Parameter Name Ref. page 257 NTP_ADDR TIME_SYNC_INTVL page 257 page 257...
Page 174 5.1 Configuration File Parameter List Language Settings Parameter Name Ref. page 263 AVAILABLE_LANGUAGE page 264 DEFAULT_LANGUAGE LANGUAGE_PATHx page 264 LANGUAGE_VERx page 264 page 264 AVAILABLE_LANGUAGE_WEB page 264 WEB_LANGUAGE WEB_LANGUAGE_PATHx page 265 WEB_LANGUAGE_VERx page 265 NAT Settings Parameter Name Ref. page 265 STUN_SERV_ADDR page 265 STUN_SERV_PORT...
Page 175 5.1 Configuration File Parameter List Parameter Name Ref. SIP_DNSSRV_ENA_NAPTR_n page 270 page 270 SIP_SVCDOMAIN_n page 270 SIP_AUTHID_n page 271 SIP_PASS_n page 271 SIP_SRC_PORT_n page 271 DSCP_SIP_n page 272 SIP_DNSSRV_ENA_n page 272 SIP_UDP_SRV_PREFIX_n page 272 SIP_TCP_SRV_PREFIX_n page 273 REG_EXPIRE_TIME_n REG_INTERVAL_RATE_n page 273 REG_RTX_INTVL_n page 273 USE_DEL_REG_OPEN_n...
Page 176 5.1 Configuration File Parameter List Parameter Name Ref. SIP_ANM_HOSTNAME_n page 279 page 279 SIP_DETECT_SSAF_n SIP_RCV_DET_HEADER_n page 280 SIP_RCV_DET_REQURI_n page 280 SIP_CONTACT_ON_ACK_n page 280 VOICE_MESSAGE_AVAILABLE page 281 SIP_INVITE_EXPIRE_n page 281 SIP_FOVR_NORSP_n page 281 SIP_FOVR_MAX_n page 281 SIP_FOVR_MODE_n page 282 SIP_FOVR_DURATION_n page 282 SIP_ADD_ROUTE_n page 282 SIP_REQURI_PORT_n...
Page 177 5.1 Configuration File Parameter List Parameter Name Ref. ESCAPECODE_CONVERSION page 288 SIP_REPLACE_ENABLE_n page 288 SIP_REFRESHER_n page 288 ENH_FOVR_ENABLE_n page 289 ENH_FOVR_RANDOM_TIMER_n page 289 ENH_FOVR_RANDOM_MAX_TIME_n page 289 ENH_FOVR_RANDOM_MIN_TIME_n page 289 SIP_INC_INVITE_RTP_MODE_n page 290 SIP_183_TALK_ENABLE page 290 SEND_180_ALERT_ENABLE page 290 INVITE_403_REGSEND_ENABLE_n page 290 ENH_FOVR_408_ENABLE_n page 291 ESCAPECODE_CONVERSION_RFC3986...
Page 178 5.1 Configuration File Parameter List Parameter Name Ref. OUTBANDDTMF_VOL page 295 INBANDDTMF_VOL page 295 DTMF_SIGNAL_LEN page 296 DTMF_INTDIGIT_TIM page 296 RTP/RTCP/RTCP-XR Settings Parameter Name Ref. page 296 DSCP_RTP_n page 296 DSCP_RTCP_n MAX_DELAY_n page 296 MIN_DELAY_n page 297 NOM_DELAY_n page 297 page 297 RTP_PORT_MIN page 298...
Page 179 5.1 Configuration File Parameter List Parameter Name Ref. page 302 ALERT_REPORT_TRIGGER page 302 ALERT_REPORT_MOSQ_CRITICAL page 303 ALERT_REPORT_MOSQ_WARNING page 303 ALERT_REPORT_DELAY_CRITICAL page 303 ALERT_REPORT_DELAY_WARNING VQREPORT_SIGNAL_COMPRESSION page 303 VQREPORT_SEND_OPT_CODEC_ENABLE page 303 VQREPORT_SEND_OPT_NW_CHANGE page 304 uaCSTA Settings Parameter Name Ref. UACSTA_ENABLE_n page 304 UACSTA_UNIQUE_ID page 304 CSTA_PORT...
Page 180 5.1 Configuration File Parameter List Parameter Name Ref. page 308 CALLPARK_KEY_ENABLE page 309 NUM_PLAN_PARK_RETRIEVING page 309 IDLE_SOFT_KEY_PARK_RETRIEVING HOLD_RECALL_TIM page 309 HOLD_TRANSFER_OPERATION page 309 ONHOOK_TRANSFER_ENABLE page 310 ONHOOK_HOLD_TRNS_ENABLE page 310 BLIND_TRANSFER_ENABLE page 310 page 310 SYS_LOCK_ENABLE page 310 SYS_LOCK_PASSWORD PAUSE_INPUT_ENABLE page 311 page 311 NUM_PLAN_PICKUP_DIRECT page 311...
Page 181 5.1 Configuration File Parameter List Parameter Name Ref. FLEX_BUTTON_QUICK_DIALx page 316 LONG_PRESS_KEY_SETTING_ENABLE page 316 DSS Key Settings Parameter Name Ref. page 317 DSS_BUTTON_FACILITY_ACTx page 318 DSS_BUTTON_FACILITY_ARGx page 318 DSS_BUTTON_LABELx DSS_BUTTON_QUICK_DIALx page 318 Tone Settings Parameter Name Ref. OUTSIDE_DIAL_TONE_FRQ page 318 OUTSIDE_DIAL_TONE_GAIN page 318 OUTSIDE_DIAL_TONE_RPT...
Page 182 5.1 Configuration File Parameter List Parameter Name Ref. page 323 REORDER_TONE_FRQ REORDER_TONE_GAIN page 323 REORDER_TONE_RPT page 324 page 324 REORDER_TONE_TIMING page 324 RINGBACK_TONE_FRQ RINGBACK_TONE_GAIN page 324 RINGBACK_TONE_RPT page 324 page 325 RINGBACK_TONE_TIMING HOLD_ALARM_FRQ page 325 HOLD_ALARM_GAIN page 325 CW_TONE1_FRQ page 325 CW_TONE1_GAIN page 326 HOLD_TONE_FRQ...
Page 183 5.1 Configuration File Parameter List Parameter Name Ref. page 331 DIAL_PLAN_NOT_MATCH_ENABLE_n DIALPLAN_REPLACE_LOG_ENABLE page 331 DIALPLAN_MEMORY_DIAL_ENABLE page 332 page 332 MACRODIGIT_TIM page 332 INTERNATIONAL_ACCESS_CODE page 332 COUNTRY_CALLING_CODE page 332 NATIONAL_ACCESS_CODE page 333 IDLE_SOFT_KEY_A page 333 IDLE_SOFT_KEY_B page 333 IDLE_SOFT_KEY_C page 334 ADMIN_ABILITY_ENABLE page 334 EMERGENCY_CALLx...
Page 184 5.1 Configuration File Parameter List Parameter Name Ref. page 340 RESOURCELIST_URI_n TALKING_SOFT_KEY_A page 340 TALKING_SOFT_KEY_B page 340 TALKING_SOFT_KEY_C page 341 page 342 AUTO_ANS_ENABLE AUTO_ANS_OPER_ENABLE page 342 page 342 AUTO_ANS_DEVICE page 343 AUTO_ANS_DELAY page 343 AUTO_ANS_TYPE RETRIVE_TRANS_HOLD_OPER_CHANGE page 343 REMOVE_PREFIX_ENABLE page 343 Video Communication Settings Parameter Name Ref.
Page 185 5.1 Configuration File Parameter List Parameter Name Ref. page 348 NWCAMERA_ALARM_NOTIFICATION page 348 NWCAMERA_ALARM_DISARM_TIME page 348 NWCAMERA_ALARM_PORT NWCAMERA_AUTO_CLOSE_ENABLE page 349 NWCAMERA_OPEN_RECEIVE_CALL page 349 Communication Camera Settings Parameter Name Ref. page 349 COMM_CAMERA_NUMBERx page 349 COMM_CAMERA_NAMEx page 350 COMM_CAMERA_RINGTONE_SETTINGx DTMF_CONTROL_UP_CAMERAx page 350 DTMF_CONTROL_DOWN_CAMERAx page 350 DTMF_CONTROL_LEFT_CAMERAx...
Page 186: General Information On The Configuration Files
KX-HDV430: 1–16 Examples of setting the line (phone number) for accessing a voice mail server. Parameter Name Examples are as follows : KX-HDV130: VM_NUMBER_1, VM_NUMBER_2 KX-HDV230: VM_NUMBER_1, VM_NUMBER_2, ..., VM_NUMBER_6 KX-HDV330: VM_NUMBER_1, VM_NUMBER_2, ..., VM_NUMBER_12 KX-HDV430: VM_NUMBER_1, VM_NUMBER_2, ..., VM_NUMBER_16 Value Format Each parameter value is categorized into Integer, Boolean, or String.
Page 187: Characters Available For String Values
5.2.2 Characters Available for String Values • String: sequence of alphanumerical characters For details about available characters, see 5.2.2 Characters Available for String Values. • Comma-separated Integer: a list of integers, separated by commas No space characters are allowed. • Comma-separated String: a list of strings, separated by commas No space characters are allowed.
Page 188: System Settings
5.3 System Settings 5.3 System Settings 5.3.1 System Settings FACTORY_RESET_ENABLE Value Format BOOLEAN Description Specifies whether to enable or disable the operation of factory default and carrier default. Value Range • Y: Enable factory reset operation • N: Disable Default Value BUTTON_LOCATION_SETTING (For KX-HDV230/KX-HDV330/KX-HDV430) Value Format INTEGER...
Page 189 5.3.1 System Settings Default Value Location numbers (x=1–20) of the icons on the Home menu. Page 2 Page 3 Page 1 FWD_DND_MENU_ENABLE Value Format BOOLEAN Description Specifies whether the "FWD/DND" setting is displayed in MENU and the Web user interface. Value Range •...
Page 190 Specifies whether the "Time Zone" setting is displayed in MENU and the Web user interface. Value Range • Y: Displayed • N: Not displayed Default Value DISCLOSE_FUNCTION_ENABLE (For KX-HDV130/KX-HDV230) Value Format BOOLEAN Description Specifies whether to disclose functions and some keys for HOTEL telephone. Value Range •...
Page 191 5.3.1 System Settings DISPLAY_CALL_KEY_ENABLE Value Format BOOLEAN Description Specifies whether call information is displayed on Line and BLF program/DSS keys. Value Range • Y: Displayed • N: Not displayed Default Value LCD_SCREEN_TIMEOUT (For KX-HDV330/KX-HDV430) Value Format INTEGER Description Specifies the length of time before the LCD backlight turns off when the unit is idle.
Page 192 5.3.1 System Settings Description Specifies the activation of the backlight of DSS units' LCD. Value Range • 0: Off • 1: On • 2: Auto Default Value DSS_LCD_BACKLIGHT (For KX-HDV330/KX-HDV430) Value Format INTEGER Description Specifies the backlight level of DSS units' LCD. Value Range 1–6 Default Value...
Page 193 5.3.1 System Settings NOTIFY_MISSEDCALL_ENABLE Value Format BOOLEAN Description Specifies whether to display 'Missed Calls' on the screen in standby mode. Note • This setting is available only when "NOTIFICATION_MENU_ENABLE" is set to "Y". • Value Range Y: Enable displaying 'Missed Calls' in standby mode. •...
Page 194 5.3.1 System Settings Description Specifies whether the LED is used to indicate a missed call Note • This setting is available only when "NOTIFICATION_MENU_ENABLE" is set to "Y". Value Range • Y: Enable LED indication for a missed call. • N: Disable Default Value Web User Interface Reference...
Page 195 5.3.1 System Settings Description Specifies whether the LED is used to indicate a Network Camera alert. Note • This setting is available only when "NOTIFICATION_MENU_ENABLE" is set to "Y". • Value Range Y: Enable LED indication for Network Camera alerts. •...
Page 196 5.3.1 System Settings Default Value BOOTLOG_SERVER_URI Value Format STRING Description Specifies the URI for a boot logging server. Value Range Max. 256 characters Default Value Empty string DISPLAY_DIVERSION_ENABLE Value Format BOOLEAN Description Specifies whether the "Diversion" call information is displayed when receiving an incoming call.
Page 197 5.3.1 System Settings FOCUS_OPERATION_ENABLE (For KX-HDV330/KX-HDV430) Value Format BOOLEAN Description Specifies whether to change the focus or seize the line when you tap a line on the line display or combined display. Value Range • Y: Change the focus • N: Seize the line Default Value INCOMING_DISPLAY_ENABLE (For KX-HDV330/KX-HDV430)
Page 198 5.3.1 System Settings IDLE_SOFT_KEY_1 (For KX-HDV330/KX-HDV430) Value Format INTEGER Description Specifies the function of soft key 1 on the line display or combined display in standby mode. Value Range • 1: Call • 2: Phonebook • 3: Call History • 4: Function •...
Page 199 5.3.1 System Settings • Value Range 1: Call • 2: Phonebook • 3: Call History • 4: Function • 5: Park (Used when performing Park Retrieve) • 6: ACD • 7: Call Center/Call Centre • 8: My Phone • 9: Presence •...
Page 200 5.3.1 System Settings • Value Range 1: Call • 2: Phonebook • 3: Call History • 4: Function • 5: Park (Used when performing Park Retrieve) • 6: ACD • 7: Call Center/Call Centre • 8: My Phone • 9: Presence •...
Page 201 5.3.1 System Settings • Value Range 1: Call • 2: Phonebook • 3: Call History • 4: Function • 5: Park (Used when performing Park Retrieve) • 6: ACD • 7: Call Center/Call Centre • 8: My Phone • 9: Presence •...
Page 202 5.3.1 System Settings SHARED_LINE_ICON_ENABLE (For KX-HDV330/KX-HDV430) Value Format BOOLEAN Description Specifies whether to display an icon instead of the index number on shared lines on the line display or combined display. Value Range • Y: Enable displaying the icon • N: Disable Default Value TALKING_SOFT_KEY_1 (For KX-HDV330/KX-HDV430)
Page 203 5.3.1 System Settings • Value Range 0: Original • 1: Off • 2: Blind (Used when performing Blind Transfer) • 3: Park (Used when performing Call Park) • 4: Private Hold • 5: Call Center/Call Centre • 6: Phonebook • 7: Call History •...
Page 204 5.3.1 System Settings • Value Range 0: Original • 1: Off • 2: Blind (Used when performing Blind Transfer) • 3: Park (Used when performing Call Park) • 4: Private Hold • 5: Call Center/Call Centre • 6: Phonebook • 7: Call History •...
Page 205 5.3.1 System Settings • Value Range 0: Original • 1: Off • 2: Blind (Used when performing Blind Transfer) • 3: Park (Used when performing Call Park) • 4: Private Hold • 5: Call Center/Call Centre • 6: Phonebook • 7: Call History •...
Page 206 5.3.1 System Settings • Value Range Y: Enable private hold • N: Disable Default Value Web User Interface Reference Private Hold CONF_OWNER_OUT_ENABLE Value Format BOOLEAN Description Specifies whether to allow the remaining two parties in a three-party conference to continue the conversation if the conference originator leaves the conference call (Unattended Conference).
Page 207: Basic Network Settings
5.3.2 Basic Network Settings Value Range 1–65535 Default Value 2002 DTMF_OUT_ENABLE Value Format BOOLEAN Description Specifies whether received outband DTMF signals are output audibly. Value Range • Y: Enable audible outband DTMF • N: Disable Default Value CANCEL_OPERATION_MODE Value Format INTEGER Description Specifies the operation of the [ /...
Page 208 5.3.2 Basic Network Settings Description Specifies the IP address for the unit for IPv4. Note • This setting is available only when "CONNECTION_TYPE" is set to "0". • When you specify this parameter, you must specify "STATIC_SUBNET" together in a configuration file. Value Range Max.
Page 209 5.3.2 Basic Network Settings Description Specifies the IP address of the primary DNS server for IPv4. Note • This setting is available only when "CONNECTION_TYPE" is set to "0". Value Range Max. 15 characters n.n.n.n [n=0–255] Default Value Empty string Web User Interface Reference DNS1 USER_DNS2_ADDR...
Page 210 Value Format STRING Description Specifies the vendor class to option60 in DHCPv4 or option16 in DHCPv6. Value Range Max. 64 characters Default Value Panasonic CONNECTION_TYPE_IPV6 Value Format INTEGER Description Specifies the IP address setting mode for IPv6. Value Range •...
Page 211: Ethernet Port Settings
5.3.3 Ethernet Port Settings STATIC_GATEWAY_IPV6 Value Format IPADDR-V6 Description Specifies the default gateway for IPv6. Value Range Max. 39 characters n:n:n:n:n:n:n:n [n=0-FFFF, abbreviation available] Default Value Empty string Web User Interface Reference Default Gateway USER_DNS1_ADDR_IPV6 Value Format IPADDR-V6 Description Specifies the IP address of primary DNS server for IPv6. Value Range Max.
Page 212 5.3.3 Ethernet Port Settings • Value Range 1: Auto • 2: 100Mbps/Full Duplex • 3: 100Mbps/Half Duplex • 4: 10Mbps/Full Duplex • 5: 10Mbps/Half Duplex Default Value Web User Interface Reference LAN Port PHY_MODE_PC Value Format INTEGER Description Specifies the link speed and duplex mode of the PC port. Value Range •...
Page 213 5.3.3 Ethernet Port Settings Default Value Web User Interface Reference IP Phone VLAN ID VLAN_PRI_IP_PHONE Value Format INTEGER Description Specifies the priority number for the unit. Value Range 0–7 Default Value Web User Interface Reference IP Phone Priority VLAN_ID_PC Value Format INTEGER Description Specifies the VLAN ID for the PC.
Page 214 5.3.3 Ethernet Port Settings Description Specifies whether to enable or disable the LLDP-MED feature. Note • You should specify "Y" for only one of "LLDP_ENABLE", or "VLAN_ENABLE". If "Y" is specified for two or more of the parameters above, the settings are prioritized as follows: VLAN_ENABLE >LLDP_ENABLE.
Page 215: Pre-Provisioning Settings
5.3.4 Pre-Provisioning Settings • Value Range Y: Enable CDP • N: Disable Default Value Web User Interface Reference Enable CDP CDP_INTERVAL Value Format INTEGER Description Specifies the interval, in seconds, between sending each CDP frames. Value Range 1–3600 Default Value Web User Interface Reference Packet Interval 5.3.4 Pre-Provisioning Settings...
Page 216: Provisioning Settings
5.3.5 Provisioning Settings Default Value OPTION160_PROV_ENABLE Value Format BOOLEAN Description Specifies whether to enable or disable the DHCP option160 provisioning. Value Range • Y: Enable DHCP option160 provisioning • N: Disable Default Value DHCPV6_OPTION17_PROV_ENABLE Value Format BOOLEAN Description Specifies whether to enable or disable DHCPv6 option17 provisioning.
Page 217 5.3.5 Provisioning Settings Value Range Max. 384 characters Note • If this URL ends with "/" (slash), "{MODEL}.cfg" is automatically added at the end of the URL. For example, CFG_PRODUCT_FILE_PATH="http://host/ dir/" becomes CFG_PRODUCT_FILE_PATH="http:// host/dir/{MODEL}.cfg". • For details about the formats, see 2.1.3 Server Address Formats.
Page 218 5.3.5 Provisioning Settings Web User Interface Reference Resync Interval CFG_RESYNC_TIME Value Format STRING Description Specifies the time (hour:minute) that the unit checks for updates of configuration files. Value Range 00:00–23:59 Note • If the value for this setting is any valid value other than an empty string, the unit downloads the configuration files at the fixed time.
Page 219 5.3.5 Provisioning Settings • Value Range 0: Provisioning • 1: TR-069 Inform • 2: Reboot Default Value CFG_FILE_KEY2 Value Format STRING Description Specifies the encryption key (password) used to decrypt configuration files. Note • If the extension of the configuration file is ".e2c", the configuration file will be decrypted using this key.
Page 220 5.3.5 Provisioning Settings Description Specifies the URI where the root certificate is stored. Note • Changing this setting may require restarting the unit. Value Range Max. 384 characters Note • For details about the formats, see 2.1.3 Server Address Formats. Default Value Empty string CFG_CLIENT_CERT_PATH...
Page 221: Firmware Update Settings
5.3.6 Firmware Update Settings • Value Range 0: No verification of root certificate • 1: Simple verification of root certificate • 2: Precise verification of root certificate Note • If set to "0", the verification of the root certificate is disabled. •...
Page 222 Note • Manual firmware updates from the Web user interface (→ see 4.7.3 Upgrade Firmware (For KX-HDV130/KX-HDV230)) can be performed regardless of this setting. (For KX-HDV130/ KX-HDV230) • Firmware updates using TR-069 can be performed regardless of this setting.
Page 223: Http Settings
5.3.7 HTTP Settings Description Specifies, in minutes, a time range during which connected units can access the server. Units will download the firmware file at a random time within this range. Value Range 0–1439 Default Value 5.3.7 HTTP Settings HTTP_VER Value Format INTEGER Description...
Page 224 5.3.7 HTTP Settings Value Range Max. 128 characters Default Value Empty string Web User Interface Reference Authentication ID HTTP_AUTH_PASS Value Format STRING Description Specifies the authentication password required to access the HTTP server. Value Range Max. 128 characters Default Value Empty string Web User Interface Reference Authentication Password...
Page 225: Httpd/Web Settings
5.3.8 HTTPD/WEB Settings HTTP_PROXY_PASS Value Format STRING Description Specifies the password for connecting HTTP proxy. Value Range Max. 128 characters Default Value Empty string 5.3.8 HTTPD/WEB Settings HTTPD_LISTEN_PORT Value Format INTEGER Description Specifies the port number of own HTTP server. Value Range 80, 1024–49151 Default Value...
Page 226 5.3.8 HTTPD/WEB Settings Value Range Max. 16 characters (except !, ", #, $, %, &, ', (, ),@, *, +, ,, /, :, ;, <, =, >, ?, [, ], ^, `, {, |, }, ~, \ and space) Note •...
Page 227: Settings
5.3.9 TR-069 Settings Value Range 6–64 characters (except !, ", #, $, %, &, ', (, ),@, *, +, ,, /, :, ;, <, =, >, ?, [, ], ^, `, {, |, }, ~, \ and space) Note • A hyphen (-) cannot be used as the first character.
Page 228 5.3.9 TR-069 Settings Default Value PERIODIC_INFORM_INTERVAL Value Format INTEGER Description Specifies the interval length, in seconds, when the CPE must attempt to connect with the ACS and call the Inform method. Note • This setting is available only when "PERIODIC_INFORM_ENABLE" is set to "Y". Value Range 30–2419200 Default Value...
Page 229 5.3.9 TR-069 Settings Default Value Empty string CON_REQ_PASS Value Format STRING Description Specifies the password used to authenticate an ACS making a Connection Request to the CPE. Note • When the "CON_REQ_USER_ID" parameter is specified, an empty string for this parameter is not allowed. Value Range Max.
Page 230 5.3.9 TR-069 Settings Description Specifies the port number of the STUN server for the CPE to send Binding Requests. Note • This setting is available only when "ANNEX_G_STUN_ENABLE" is set to "Y". Value Range 1–65535 Default Value 3478 ANNEX_G_STUN_USER_ID Value Format STRING Description Specifies the STUN user name to be used in Binding Requests (only...
Page 231 5.3.9 TR-069 Settings ANNEX_G_STUN_MIN_KEEP_ALIVE Value Format INTEGER Description Specifies the minimum period, in seconds, that STUN Binding Requests can be sent by the CPE for the purpose of maintaining the binding in the Gateway. This limit applies only to Binding Requests sent from the UDP Connection Request address and port, and only those that do not contain the BINDING-CHANGE attribute.
Page 232: Xml Settings
5.3.10 XML Settings 5.3.10 XML Settings XMLAPP_ENABLE Value Format BOOLEAN Description Specifies whether to enable the XML application feature. Value Range • Y: Enable XML application • N: Disable Default Value Web User Interface Reference Enable XMLAPP XMLAPP_USERID Value Format STRING Description Specifies the authentication ID required to access the XML...
Page 233 5.3.10 XML Settings Web User Interface Reference User ID XMLAPP_LDAP_USERPASS Value Format STRING Description Specifies the authentication password used to access the LDAP server. Value Range Max. 128 characters Default Value Empty string Web User Interface Reference Password XMLAPP_NPB_SEARCH_TIMER Value Format INTEGER Description Specifies the time which is for searching XML phonebook.
Page 234 5.3.10 XML Settings XMLAPP_START_URL Value Format STRING Description Specifies the URL that is accessed when the unit starts up, to check for XML data. Value Range Max. 256 characters Default Value Empty string Web User Interface Reference Bootup URL XMLAPP_INITIAL_URL Value Format STRING Description...
Page 235 Value Range Max. 256 characters Default Value Empty string Web User Interface Reference Idling URL XML_INITIATE_KEY_SOFT1 (For KX-HDV130/KX-HDV230) Value Format BOOLEAN Description Specifies whether to enable the XML application or operate the telephone normally, when the corresponding button is pressed during standby mode.
Page 236 • Y: XML Mode • N: Normal Telephone Mode Default Value Web User Interface Reference Enable FF Key XML_SOFT_KEY_NAMEx (For KX-HDV130/KX-HDV230) Value Format STRING Description x=1‐3 Specifies the name of Soft Key A/B/C assigned to an XML application. Value Range Max.
Page 237 5.3.10 XML Settings XMLAPP_STATUSBAR_ENABLE (For KX-HDV330/KX-HDV430) Value Format BOOLEAN Description Specifies whether to enable or disable the Status Bar XML application feature. Value Range • Y: Enable the Status Bar XML application feature • N: Disable Default Value SYS_HOME_MENU_XML_NAMEx (For KX-HDV330/KX-HDV430) Value Format STRING Description...
Page 238 5.3.10 XML Settings Note • No.12, 16, 20–29: Blank XML_PHONEBOOK_URL Value Format STRING Description Specifies the URL to download the XML phonebook file from. Value Range Max.256 characters Default Value Empty string XML_PHONEBOOK_CYCLIC_INTVL Value Format INTEGER Description Specifies the interval, in minutes, between periodic checks for updates to the XML phonebook.
Page 239: Xsi Settings
5.3.11 XSI Settings Description X=1-20 Specifies the IP addresses from which XML (POST) may be received. Note • If no IP addresses are specified, XML (POST) can be received from any IP address Value Range Max. 15 characters n.n.n.n [n=0-255] Default Value Empty string 5.3.11 XSI Settings...
Page 240 5.3.11 XSI Settings Web User Interface Reference Port XSI_USERID_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format STRING Description Specifies the authentication ID required to access the Xsi server. Value Range Max. 128 characters Default Value Empty string Web User Interface Reference...
Page 241 5.3.11 XSI Settings Description Specifies the time range, in minutes, during which connected units can access the server. Xsi Directory (Phonebook) files will be downloaded at a random time within this range. Value Range 0–1439 Default Value XSI_PHONEBOOK_TYPE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format INTEGER Description...
Page 242 5.3.11 XSI Settings Description Specifies whether to enable or disable the XSI SIP Credentials feature. Value Range • Y: Enable XSI SIP Credentials • N: Disable Default Value Web User Interface Reference SIP Credentials BSD_MULTI_TYPE_ENABLE Value Format BOOLEAN Description Specifies whether you can select the type of Xsi phonebook. Value Range •...
Page 243: Xmpp (Uc-One) Settings
5.3.12 XMPP (UC-ONE) Settings • Value Range Y : Enable • N : Disable Default Value Web User Interface Reference Enterprise BSD_ENTERPRISECOM_ENABLE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether to enable or disable the "EnterpriseCommon" type for Xsi phonebooks.
Page 244 5.3.12 XMPP (UC-ONE) Settings Default Value Empty string Web User Interface Reference User ID UC_PASSWORD Value Format STRING Description Specifies the authentication password required to access the UC server. Value Range Max. 128 characters Default Value Empty string Web User Interface Reference Password XMPP_SERVER Value Format...
Page 245 5.3.12 XMPP (UC-ONE) Settings Default Value Empty string XMPP_CLIENT_CERT_PATH Value Format STRING Description Specifies the URI where the client certificate is stored. Value Range Max. 384 characters Note • For details about the formats, see 2.1.3 Server Address Formats. Default Value Empty string XMPP_PKEY_PATH Value Format...
Page 246: Ldap Settings
5.3.13 LDAP Settings • Value Range Y : Enable • N : Disable Default Value PRESENCE_MYPHONE_STATUS Value Format INTEGER Description Specifies the default status of "My Phone" when "Presence" starts up. Value Range – 0: Available – 1: Away – 2: Busy –...
Page 247 5.3.13 LDAP Settings Default Value Web User Interface Reference Enable DNS SRV lookup LDAP_SERVER Value Format STRING Description Specifies the server host of LDAP. Value Range Max. 256 characters Note • The LDAP server address should start with "ldap://" or "ldaps://".
Page 248 5.3.13 LDAP Settings LDAP_USERID Value Format STRING Description Specifies the authentication ID required to access the LDAP server. Value Range Max. 128 characters Default Value Empty string Web User Interface Reference User ID LDAP_PASSWORD Value Format STRING Description Specifies the authentication password required to access the LDAP server.
Page 249 5.3.13 LDAP Settings LDAP_NUMB_ATTRIBUTE Value Format STRING Description Specifies the number attributes of each record which are to be returned in the LDAP search result. Value Range Max. 256 characters Default Value telephoneNumber,mobile,homePhone Web User Interface Reference Number Attributes LDAP_BASEDN Value Format STRING Description...
Page 250: Call Center Settings
5.3.14 Call Center Settings Default Value Empty string LDAP_PKEY_PATH Value Format STRING Description Specifies the URI where the private key is stored. Value Range Max. 384 characters Note • For details about the formats, see 2.1.3 Server Address Formats. Default Value Empty string LDAP_DISPLAY_FORMAT Value Format...
Page 251 5.3.14 Call Center Settings ACD_LOGIN_CONDITION_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format INTEGER Description Specifies the ACD state when login to the ACD. Value Range • 0: Available • 1: Unavailable Default Value ACD_LOGOUT_CONDITION_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format...
Page 252 5.3.14 Call Center Settings • Value Range Y: Enable • N: Disable Default Value Web User Interface Reference Hoteling Event HOTELING_USERID_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format STRING Description Specifies the authentication ID required to access the Hoteling service.
Page 253: Snmp Settings
5.3.15 SNMP Settings Default Value UC_FLEXIBLESEATING_UNLOCKPIN Value Format STRING Description Specifies the unlock PIN for Flexible Seating. Value Range 4–10 digits Default Value Empty string 5.3.15 SNMP Settings Note • Changing SNMP setting may require restarting the unit. SNMP_ENABLE Value Format BOOLEAN Description Specifies whether to enable SNMP feature.
Page 254 5.3.15 SNMP Settings Description Specifies the security type of SNMPv3. Value Range 0: noAuthNoPriv 1: AuthNoPriv 2: AuthPriv Default Value SNMP_SECURITY_USER Value Format STRING Description Specifies the security user ID for authentication and encryption of SNMPv3. Value Range Max. 32 characters Default Value Empty string SNMP_AUTH_TYPE...
Page 255: Multicast Paging Settings
5.3.16 Multicast Paging Settings 5.3.16 Multicast Paging Settings MPAGE_ADDRm Parameter Name Example MPAGE_ADDR1, MPAGE_ADDR2, …, MPAGE_ADDR5 Value Format IPADDR Description Specifies the address for multi-cast paging for each channel group. (m=1–5, the channel group) {Priority: 5 > 4 > 3, 2, 1 (depending on the configuration)} Value Range 224.0.0.0–239.255.255.255...
Page 256 5.3.16 Multicast Paging Settings Default Value Web User Interface Reference Priority (Group 1–3) MPAGE_LABELm Parameter Name Example MPAGE_LABEL1, MPAGE_LABEL2, …, MPAGE_LABEL5 Value Format STRING Description Specifies a label for each channel group. (m=1–5, the channel group) Value Range Max. 24 characters Default Value Empty string Web User Interface Reference...
Page 257: Ntp Settings
5.3.17 NTP Settings Description Specifies the speaker level for new received multi-cast paging (priority channel). Value Range 0–8 0: No control Default Value MPAGE_DND_ENABLE Value Format BOOLEAN Description Specifies the DND setting (on/off) for multi-cast paging. Value Range • Y: Enable DND for Multi-cast paging •...
Page 258: Time Settings
5.3.18 Time Settings Description Specifies the interval, in seconds, between synchronizations with the NTP server. Value Range 10–86400 Default Value 43200 Web User Interface Reference Synchronization Interval (Synchronisation Interval) 5.3.18 Time Settings LOCAL_TIME_ZONE_POSIX Value Format STRING Description Specifies a IEEE 1003.1 (POSIX)-compliant local time zone definition (e.g., "EST+5 EDT,M4.1.0/2,M10.5.0/2").
Page 259 5.3.18 Time Settings Value Range -720–780 Note • Only the following values are available: -720 (GMT -12:00), -660 (GMT -11:00), -600 (GMT -10:00), -540 (GMT -09:00), -480 (GMT -08:00), -420 (GMT -07:00), -360 (GMT -06:00), -300 (GMT -05:00), -240 (GMT -04:00), -210 (GMT -03:30), -180 (GMT -03:00), -120 (GMT -02:00), -60 (GMT -01:00), 0 (GMT), 60 (GMT +01:00), 120 (GMT +02:00), 180 (GMT +03:00), 210 (GMT +03:30), 240 (GMT +04:00), 270...
Page 260 5.3.18 Time Settings Value Range 0–720 Note • This parameter is usually set to "60". Default Value Web User Interface Reference DST Offset (Summer Time Offset) DST_START_MONTH Value Format INTEGER Description Specifies the month in which DST (Summer Time) starts. Note •...
Page 261 5.3.18 Time Settings Description Specifies the day of the week on which DST (Summer Time) starts. Note • This parameter is disabled when the "LOCAL_TIME_ZONE_POSIX" parameter is specified. Value Range 0–6 – 0: Sunday – 1: Monday – 2: Tuesday –...
Page 262 5.3.18 Time Settings Description Specifies the number of the week on which DST (Summer Time) ends. The actual end day is specified in "DST_STOP_DAY_OF_WEEK". For example, to specify the second Sunday, specify "2" in this parameter, and "0" in the next parameter. Note •...
Page 263: Network Phonebook (Common)
5.3.19 Network Phonebook (Common) Description Specifies the end time of DST (Summer Time) in minutes after 12:00 Note • This parameter is disabled when the "LOCAL_TIME_ZONE_POSIX" parameter is specified. Value Range 0–1439 Default Value Web User Interface Reference Time 5.3.19 Network Phonebook (Common) ONLY_NPB_ENABLE Value Format BOOLEAN...
Page 264 5.3.20 Language Settings Value Range en, es, fr, de, it, da, nl, sv, fi, el, hu, pt, pl, sk, cs, sh, ru, uk, tr, no, ro, ct, kk, me → see 4.4.1.1 Selectable Language Web User Interface Reference IP Phone DEFAULT_LANGUAGE Value Format STRING...
Page 265: Nat Settings
5.3.21 NAT Settings Description Specifies the default language on the unit. Value Range en, es, fr, de, it, nl, el, hu, pt, pl, sk, cs, sh, ru, uk, tr, ro, ct, kk, me → see 4.4.1.1 Selectable Language Default Value Web User Interface Reference Web Language WEB_LANGUAGE_PATHx...
Page 266 5.3.21 NAT Settings Default Value 3478 Web User Interface Reference Port STUN_2NDSERV_ADDR Value Format STRING Description Specifies the IP address or FQDN of the secondary STUN server. Value Range Max. 256 characters Default Value Empty string STUN_2NDSERV_PORT Value Format INTEGER Description Specifies the port number of the secondary STUN server.
Page 267: Sip Settings
0: Disable Default Value Web User Interface Reference Enable Port Punching for RTP EXTERNAL_RTP_PORTx Value Format INTEGER Description KX-HDV130 : x=1-3 KX-HDV230/KX-HDV330 : x=1-24 KX-HDV430 : x=1-48 Specifies the port number of the router in Static NAT status. Value Range •...
Page 268 5.3.22 SIP Settings PHONE_NUMBER_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format STRING Description Specifies the phone number to use as the user ID required for registration to the SIP registrar server. Note •...
Page 269 5.3.22 SIP Settings Description Specifies the port number to use for communication with the SIP registrar server. Value Range 1–65535 Default Value 5060 Web User Interface Reference Registrar Server Port SIP_PRXY_ADDR_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format STRING Description...
Page 270 5.3.22 SIP Settings SIP_OUTPROXY_ADDR_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format STRING Description Specifies the IP address or FQDN of the SIP outbound proxy server. Value Range Max. 256 characters Default Value Empty string Web User Interface Reference Outbound Proxy Server Address...
Page 271 5.3.22 SIP Settings Value Range Max. 128 characters (except ", &, ', :, <, >, and space) Default Value Empty string Web User Interface Reference Authentication ID SIP_PASS_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format STRING Description...
Page 272 5.3.22 SIP Settings Value Range 0–63 Default Value Web User Interface Reference SIP Packet QoS (DSCP) SIP_DNSSRV_ENA_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether to request the DNS server to translate domain names into IP addresses using the SRV record.
Page 273 5.3.22 SIP Settings Description Specifies a prefix to add to the domain name when performing a DNS SRV lookup using TCP. Note • This setting is available only when "SIP_DNSSRV_ENA_n" is set to "Y". Value Range Max. 32 characters Default Value _sip._tcp.
Page 274 5.3.22 SIP Settings Description Specifies whether to enable cancelation before registration when, for example, the unit is turned on. Value Range • Y: Send un-REGISTER • N: Does not send Default Value USE_DEL_REG_CLOSE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description...
Page 275 5.3.22 SIP Settings Description Specifies the default interval, in milliseconds, between transmissions of SIP messages. For details, refer to RFC 3261. Value Range • • • 1000 • 2000 • 4000 Default Value Web User Interface Reference T1 Timer SIP_TIMER_T2_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format INTEGER...
Page 276 5.3.22 SIP Settings Description Specifies the value of SIP timer B (INVITE transaction timeout timer), in milliseconds. For details, refer to RFC 3261. Value Range 250–64000 Default Value 32000 SIP_TIMER_D_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format INTEGER Description...
Page 277 5.3.22 SIP Settings Description Specifies whether to add the option tag 100rel to the "Supported" header of the INVITE message. For details, refer to RFC 3262. Value Range • Y: Enable 100rel function • N: Disable 100rel function Note • If set to "Y", the Reliability of Provisional Responses function will be enabled.
Page 278 5.3.22 SIP Settings Value Format INTEGER Description Specifies the interval, in seconds, between transmissions of SUBSCRIBE requests when a subscription results in failure (server no reply or error reply). Value Range 1–86400 Default Value SIP_P_PREFERRED_ID_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description...
Page 279 5.3.22 SIP Settings SIP_ANM_DISPNAME_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format INTEGER Description Specifies the text string to set as the display name in the "From" header when making anonymous calls. Value Range •...
Page 280 5.3.22 SIP Settings • Value Range Y: Enable SSAF • N: Disable SSAF Note • If set to "Y", the unit receives SIP messages only from the source addresses stored in the SIP servers (registrar server, proxy server, and presence server), and not from other addresses.
Page 281 5.3.22 SIP Settings Description Specifies whether to add the "Contact" header to SIP ACK message. Value Range • Y: Add the "Contact" header • N: Do not add the "Contact" header Default Value VOICE_MESSAGE_AVAILABLE Value Format BOOLEAN Description Specifies how the existence of voice messages is determined when a "Messages-Waiting: yes"...
Page 282 5.3.22 SIP Settings Description Specifies the maximum number of servers (including the first [normal] server) used in the fail-over process. Value Range 1–4 Default Value SIP_FOVR_MODE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether INVITE/SUBSCRIBE will also follow the...
Page 283 5.3.22 SIP Settings • Value Range Y: Add the port parameter • N: Do not add the port parameter Note • Request URI in REGISTER example: – If set to "Y", the port parameter is added to the Request- Line, as follows: Request-Line: REGISTER sip:192.168.0.10:5060 SIP/2.0 –...
Page 284 5.3.22 SIP Settings TRANSFER_RECALL_TIM Value Format INTEGER Description Specifies the time that the original call is resumed when the forwarding party does not response by Refer method for call transfer. Value Range 0, 1–240 Default Value SIGNAL_COMPRESSION_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format INTEGER Description...
Page 285 5.3.22 SIP Settings SIP_403_REG_SUB_RTX_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether or not to send a request when a 403 Forbidden reply is received from the server in response to a REGISTER or SUBSCRIBE.
Page 286 5.3.22 SIP Settings Web User Interface Reference Enable c=0.0.0.0 Hold (RFC 2543) SIP_HOLD_ATTRIBUTE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format INTEGER Description Specifies whether to set "a=inactive " or not when the call is on hold. Value Range •...
Page 287 5.3.22 SIP Settings Value Range 0–1 – 0: The unit’s hold tone is played. – 1: The network server’s hold tone (Music on hold) is played. Default Value KEEP_EARLYMEDIA_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description...
Page 288 5.3.22 SIP Settings Description Specifies whether to support RFC6947 draft08 when the attvalue is not attached after altc. Value Range • Y: Performs ALTC by Draft08 • N: Performs ALTC by RFC6947 Default Value RFC5627_SUPPORT_GRUU_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description...
Page 289 5.3.22 SIP Settings Default Value ENH_FOVR_ENABLE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether to enable Enhanced Failover mode. Value Range • Y: Enable • N: Disable Default Value ENH_FOVR_RANDOM_TIMER_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format...
Page 290 5.3.22 SIP Settings Description Specifies the minimum value, in seconds, of the retry timer, which determines the interval for re-sending REGISTER requests, when the retry timer is set to be a random value. Note • This setting is available only when "ENH_FOVR_RANDOM_TIMER_n"...
Page 291: Sip-Tls Settings
5.3.23 SIP-TLS Settings Default Value ENH_FOVR_408_ENABLE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether to enable failover after receiving a 408 error from the SIP server. Value Range • Y: Enable •...
Page 292 5.3.23 SIP-TLS Settings Web User Interface Reference TLS Mode SIP_TLS_RECONNECT_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether to perform TLS reconnect after TLS session is disconnected. Value Range •...
Page 293: Codec Settings
5.3.24 CODEC Settings SIP_TLS_CLIENT_CERT_PATH Value Format STRING Description Specifies the URI where the client certificate is stored. Value Range Max. 384 characters Note • For details about the formats, see 2.1.3 Server Address Formats. Default Value Empty string SIP_TLS_PKEY_PATH Value Format STRING Description Specifies the URI where the private key is stored.
Page 294 5.3.24 CODEC Settings CODEC_ENABLEx_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether to enable the codec specified in the parameter list. Note • The "x" character in the parameter title should be changed to one of the following numbers, according to the codec to be changed.
Page 295: Dtmf Settings
5.3.25 DTMF Settings • Web User Interface Reference G.722 Priority • PCMA Priority • G.729A Priority • PCMU Priority CODEC_G711_REQ Value Format INTEGER Description Specifies whether to automatically select "PCMU" as the codec when a codec other than "PCMU" is selected. Value Range •...
Page 296: Rtp/Rtcp/Rtcp-Xr Settings
5.3.26 RTP/RTCP/RTCP-XR Settings Value Range -46–0 Default Value DTMF_SIGNAL_LEN Value Format INTEGER Description Specifies the length of the DTMF signal, in milliseconds. Value Range 60–200 Default Value DTMF_INTDIGIT_TIM Value Format INTEGER Description Specifies the interval, in milliseconds, between DTMF signals. Value Range 60–200 Default Value...
Page 297 5.3.26 RTP/RTCP/RTCP-XR Settings Value Range 3–50 (× 10 ms) Note • This setting is subject to the following conditions: – This value must be greater than "NOM_DELAY" – This value must be greater than "MIN_DELAY" – "NOM_DELAY" must be greater than or equal to "MIN_DELAY"...
Page 298 5.3.26 RTP/RTCP/RTCP-XR Settings Default Value 16000 Web User Interface Reference Minimum RTP Port Number RTP_PORT_MAX Value Format INTEGER Description Specifies the highest port number that the unit will use for RTP packets. Value Range 1424–59998 (only even) Default Value 20000 Web User Interface Reference Maximum RTP Port Number RTP_PTIME...
Page 299: Srtp Settings
5.3.27 SRTP Settings RTCP_SEND_BY_SDP_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format INTEGER Description Specifies whether to send RTCP signals by SDP (Session Description Protocol). Value Range 0–1 – 0: Send RTCP signals using the value specified in "RTCP_INTVL_n", if the "RTCP_ENABLE_n"...
Page 300 5.3.27 SRTP Settings • Value Range 0: SRTP • 1: RTP/SRTP • 2: Panasonic Original • 3: SRTP/RTP Note • 0: Use only SRTP for outgoing and incoming calls. • 1: Use only RTP for outgoing calls, and RTP or SRTP for incoming calls.
Page 301 5.3.27 SRTP Settings SRTP_HELD_CALL_RTP_ENABLE Value Format BOOLEAN Description Specifies whether to allow playing the melody on hold over RTP on a call that is using SRTP. Value Range • Y: Enable • N: Disable Default Value SRTP_CALL_MODE_ENABLE (For KX-HDV230/KX-HDV330/KX-HDV430) Value Format BOOLEAN Description Specifies whether to enable the unit to use only encrypted call mode...
Page 302: Vq Report By Publish
5.3.28 VQ Report by PUBLISH 5.3.28 VQ Report by PUBLISH VQREPORT_COLLECTOR_ADDRESS Value Format STRING Description Specifies the IP address or FQDN of the collector server. Value Range Max. 256 characters Default Value Empty string Web User Interface Reference Server Address VQREPORT_COLLECTOR_PORT Value Format INTEGER...
Page 303 5.3.28 VQ Report by PUBLISH Default Value Web User Interface Reference Threshold MOS-LQ (Critical) ALERT_REPORT_MOSQ_WARNING Value Format INTEGER Description Specifies the warning criteria to send VQ report at the time of occurring the MOSQ. Value Range 0–40 Default Value Web User Interface Reference Threshold MOS-LQ (Warning) ALERT_REPORT_DELAY_CRITICAL Value Format...
Page 304: Uacsta Settings
5.3.29 uaCSTA Settings Default Value VQREPORT_SEND_OPT_NW_CHANGE Value Format INTEGER Description Specifies the number of consecutive times the MOS (Mean Opinion Score) value may fall below the threshold value specified by either ALERT_REPORT_MOSQ_CRITICAL or ALERT_REPORT_MOSQ_WARNING before the phone sends VQREPORT. The ALERT_REPORT_TRIGGER setting determines whether ALERT_REPORT_MOSQ_CRITICAL or ALERT_REPORT_MOSQ_WARNING is used as the threshold.
Page 305 5.3.29 uaCSTA Settings CSTA_PRXY_ADDR Value Format STRING Description Specifies the IP address or FQDN of the proxy server for CSTA. Value Range Max. 256 characters Default Value Empty string CSTA_PRXY_PORT Value Format INTEGER Description Specifies the port of the proxy server for CSTA. Value Range 1–65535 Default Value...
Page 306: Telephone Settings
Empty string 5.3.30 Telephone Settings POWER_ON_DISPLAY_LOGO_PATH Value Format STRING Description Specifies URI for logo image file displayed when power is turned on. Note KX-HDV130/KX-HDV230 • Size: 132 × 64 • File type: BMP (1 bit) KX-HDV330/KX-HDV430 • Size: 480 × 272 •...
Page 307 5.3.30 Telephone Settings INTDIGIT_TIM Value Format INTEGER Description Specifies the length of time, in seconds, within which subsequent digits of a dial number must be dialed. Value Range 1–15 (s) Default Value Web User Interface Reference Inter-digit Timeout POUND_KEY_DELIMITER_ENABLE Value Format BOOLEAN Description Specifies whether the # key is treated as a regular dialed digit or a...
Page 308 5.3.30 Telephone Settings Description Specifies the minimum number of digits with which to match a phonebook entry with an incoming call’s caller ID. Value Range 0–15 Default Value NUMBER_MATCHING_UPPER_DIGIT Value Format INTEGER Description Specifies the maximum number of digits with which to match a phonebook entry with an incoming call’s caller ID.
Page 309 2: Soft Key B (Center) • 3: Soft Key C (Right) Default Value Web User Interface Reference Park Retrieve Soft Key (For KX-HDV130/KX-HDV230) HOLD_RECALL_TIM Value Format INTEGER Description Specifies the duration of the hold recall timer. If set to "0", the function is disabled.
Page 310 5.3.30 Telephone Settings Default Value ONHOOK_TRANSFER_ENABLE Value Format BOOLEAN Description Specifies whether to enable on hook transfer when HOLD_TRANSFER_OPERATION="N". Value Range • Y: Enable On-hook Transfer • N: Disable On-hook Transfer Default Value ONHOOK_HOLD_TRNS_ENABLE Value Format BOOLEAN Description Specifies whether to enable on hook transfer when HOLD_TRANSFER_OPERATION="Y".
Page 311 5.3.30 Telephone Settings PAUSE_INPUT_ENABLE Value Format BOOLEAN Description Specifies whether to enable or disable pause input. Value Range • Y: Enable • N: Disable Default Value NUM_PLAN_PICKUP_DIRECT Value Format STRING Description Specifies the feature number assigned to a BLF for performing call pickup.
Page 312 Number Identification Presentation) on the display when calling. Value Range • Y: Enable • N: Disable Default Value SOFT_KEY_LABELx (For KX-HDV130/KX-HDV230) Value Format STRING Description x=1-3 Specifies the text of the soft keys displayed on the screen for quick dialing.
Page 313 5.3.30 Telephone Settings Default Value SOFT_KEY_LABEL1: 1 SOFT_KEY_LABEL2: 2 SOFT_KEY_LABEL3: 3 SOFT_KEY_QUICK_DIALx (For KX-HDV130/KX-HDV230) Value Format STRING Description x=1-3 Specifies quick-dial numbers to assign to the soft keys. Note This setting is available only when "DISCLOSE_FUNCTION_ENABLE" is set to "Y".
Page 314 5.3.30 Telephone Settings • Value Range Y: Enable • N: Disable Default Value CALLPARK_METHOD Value Format INTEGER Description Specifies the method for the "Call Park" function. • Value Range 1: Info message type • 2: Refer type Default Value CALL_PARK_PROG_KEY_MODE Value Format INTEGER Description...
Page 315: Flexible Key Settings
5.3.31 Flexible Key Settings FLEX_BUTTON_FACILITY_ACTx Value Format STRING Description x=1–2 – KX-HDV130 x=1–24 – KX-HDV230/KX-HDV330/KX-HDV430 Specifies a particular Facility Action for the flexible Key. Nofacility action will be taken for the button if the string is empty or invalid. Note •...
Page 316 KX-HDV230/KX-HDV330/ : x=1–24 KX-HDV430 Specifies an optional argument associated with the specified Facility Action for the flexible Key. Value Range Max. 32 characters (For KX-HDV130) Max. 128 characters (For KX-HDV230/KX-HDV330/KX-HDV430) Default Value Empty string Web User Interface Reference Parameter FLEX_BUTTON_LABELx (For KX-HDV230/KX-HDV330/KX-HDV430)
Page 317: Dss Key Settings (For Kx-Hdv230/Kx-Hdv330/Kx-Hdv430)
5.3.32 DSS Key Settings (For KX-HDV230/KX-HDV330/KX-HDV430) Description Selects whether to enable or disable the flexible key or DSS key with a long press. Note For KX-HDV330/KX-HDV430, this function is valid only for DSS key. • Value Range Y: Enable • N: Disable Default Value 5.3.32 DSS Key Settings (For KX-HDV230/KX-HDV330/...
Page 318: Tone Settings
5.3.33 Tone Settings DSS_BUTTON_FACILITY_ARGx Value Format STRING Description x=1–200 Specifies an optional argument associated with the specified Facility Action for the flexible key. Value Range Max. 128 characters Default Value Empty string Web User Interface Reference Parameter DSS_BUTTON_LABELx Value Format STRING Description x=1–200...
Page 319 5.3.33 Tone Settings Default Value OUTSIDE_DIAL_TONE_RPT Value Format INTEGER Description Specifies whether Second Dial Tone is repeated. • Value Range 0: No Repeat • 1: Repeat Default Value OUTSIDE_DIAL_TONE_TIMING Value Format Comma-separated Integer Description Specifies the pattern, in milliseconds, of Second Dial Tone using Max. 10 whole numbers (off 1, on 1, off 2, on 2…) separated by commas.
Page 320 5.3.33 Tone Settings Description Specifies the duration, in seconds, that a disconnect tone will be heard when the other party ends a call and the unit is being used. Value Range 1–15 (s) Default Value DIAL_TONE1_FRQ Value Format Comma-separated Integer Description Specifies the dual-tone frequencies, in hertz, of Dial Tone 1 using 2 whole numbers separated by a comma.
Page 321 5.3.33 Tone Settings DIAL_TONE2_FRQ Value Format Comma-separated Integer Description Specifies the dual-tone frequencies, in hertz, of Dial Tone 2 using 2 whole numbers separated by a comma. Value Range 0, 200–2000 (Hz) (0: No tone) Default Value 350,440 DIAL_TONE2_GAIN Value Format INTEGER Description Specifies the gain, in decibels, of Dial Tone 2.
Page 322 5.3.33 Tone Settings Default Value 350,440 Web User Interface Reference Tone Frequencies DIAL_TONE4_GAIN Value Format INTEGER Description Specifies the gain, in decibels, of Dial Tone 4 (stutter-type dial tone). Value Range -24–24 (dB) Default Value DIAL_TONE4_RPT Value Format INTEGER Description Specifies whether Dial Tone 4 (stutter-type dial tone) is repeated.
Page 323 5.3.33 Tone Settings BUSY_TONE_GAIN Value Format INTEGER Description Specifies the gain, in decibels, of the busy tone. Value Range -24–24 (dB) Default Value BUSY_TONE_RPT Value Format INTEGER Description Specifies whether the busy tone is repeated. Value Range 0–1 – 0: No Repeat –...
Page 324 5.3.33 Tone Settings Default Value REORDER_TONE_RPT Value Format INTEGER Description Specifies whether the reorder tone is repeated. Value Range 0–1 – 0: No Repeat – 1: Repeat Default Value REORDER_TONE_TIMING Value Format Comma-separated Integer Description Specifies the pattern, in milliseconds, of reorder tones using up to 10 whole numbers (off 1, on 1, off 2, on 2…) separated by commas.
Page 325 5.3.33 Tone Settings Description Specifies whether the ringback tone is repeated. Value Range 0–1 – 0: No Repeat – 1: Repeat Default Value RINGBACK_TONE_TIMING Value Format Comma-separated Integer Description Specifies the pattern, in milliseconds, of ringback tones using up to 10 whole numbers (off 1, on 1, off 2, on 2…) separated by commas.
Page 326 5.3.33 Tone Settings CW_TONE1_GAIN Value Format INTEGER Description Specifies the gain, in decibels, of call waiting tone 1. Value Range -24–24 (dB) Default Value HOLD_TONE_FRQ Value Format Comma-separated Integer Description Specifies the dual-tone frequencies, in hertz, of the hold tone using 2 whole numbers separated by a comma.
Page 327 5.3.33 Tone Settings BELL_CORE_PATTERN3_TIMING Value Format Comma-separated Integer Description Specifies the cadence, in milliseconds, of pattern ID 3, described in the LSSGR, GR-506-CORE, "Signaling for Analog Interfaces" section 14, using up to 8 whole numbers (on 1, off 1, on 2, off 2…) separated by commas.
Page 328: Call Control Settings
13: Line 13 • 14: Line 14 • 15: Line 15 • 16: Line 16 Note KX-HDV130 Line 1-2 KX-HDV230 Line 1-6 KX-HDV330 Line 1-12 KX-HDV430 Line 1-16 Default Value Web User Interface Reference Default Line for Outgoing ANONYMOUS_CALL_ENABLE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters...
Page 329 5.3.34 Call Control Settings BLOCK_ANONYMOUS_CALL_ENABLE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether to accept or reject the incoming call without the called party’s phone number. Value Range • Y: Enable anonymous call block •...
Page 330 5.3.34 Call Control Settings Value Range Max. 24 characters Note • You can use Unicode characters for this setting. Default Value Empty string Web User Interface Reference Display Name VM_SUBSCRIBE_ENABLE Value Format BOOLEAN Description Specifies whether to send the SUBSCRIBE request to a voice mail server.
Page 331 5.3.34 Call Control Settings • Value Range Y: Enable • N: Disable Default Value DIAL_PLAN_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format STRING Description Specifies a dial format, such as specific phone numbers, that control which numbers can be dialed or how to handle the call when making a call.
Page 332 5.3.34 Call Control Settings DIALPLAN_MEMORY_DIAL_ENABLE Value Format BOOLEAN Description Specifies whether to enable Dial Plan processing for memory dialing. Value Range • Y: Enable Dial Plan • N: Disable Default Value MACRODIGIT_TIM Value Format INTEGER Description Specifies the length of time, in seconds, that the unit waits when a "T" or "t"...
Page 333 5.3.34 Call Control Settings Default Value Empty string Web User Interface Reference National Access Code IDLE_SOFT_KEY_A (For KX-HDV130/KX-HDV230) Value Format INTEGER Description Specifies the Soft Key A (Left) during IDLE state. Value Range • 1: Phonebook • 2: Menu •...
Page 334 5.3.34 Call Control Settings Description Specifies the Soft Key C (Right) during IDLE state. Value Range • 1: Phonebook • 2: Menu • 3: Outgoing Call Log • 4: Incoming Call Log • 5: Redial • 6: Page (Used when performing Multicast Paging) Note The following features are applied to the soft key only when the corresponding parameters are enabled.
Page 335 5.3.34 Call Control Settings Value Range Max. 32 characters (except &, ", ', :, ;, <, >) Default Value Empty string Web User Interface Reference 1–30 CLICKTO_ENABLE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description...
Page 336 5.3.34 Call Control Settings • Value Range Y: Enable shared call • N: Disable shared call Note • If set to "Y", the SIP server will control the line by using a shared-call signaling method. • If set to "N", the SIP server will control the line by using a standard signaling method.
Page 337 5.3.34 Call Control Settings • Value Range Y: Do not synchronize • N: Synchronize Default Value BS_EXECUTIVE_SETTING_ENABLE_n (For KX-HDV330/KX-HDV430) For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether to enable or disable the Executive Call Filtering feature of the selected line.
Page 338 Value Format INTEGER Description Specifies the mode of FWD/DND synchronizing with server. Value Range • 1: as feature event • 2: Panasonic original • 3: Entel Default Value FWD_DND_MISSEDLOG_ENABLE Value Format BOOLEAN Description Specifies whether to enable the unit to save forwarded calls and rejected calls on a Missed Call log when "FWD/DND"...
Page 339 5.3.34 Call Control Settings SIP_RESPONSE_CODE_CALL_REJECT Value Format INTEGER Description Specifies the response code when a call is rejected. Value Range 400–699 Default Value CW_ENABLE_n For details about parameter names end with "_n", see 5.2.1 Configuration File Parameters Value Format BOOLEAN Description Specifies whether automatic call waiting is enabled.
Page 340 "@" symbol, and a host part. Value Range Max. 256 characters Default Value Empty string Web User Interface Reference Resource List URI TALKING_SOFT_KEY_A (For KX-HDV130/KX-HDV230) Value Format INTEGER Description Specifies the display icon of soft key A during a call. Value Range •...
Page 341 – Blind: BLIND_TRANSFER_ENABLE – Park: CALLPARK_KEY_ENABLE – Pause: PAUSE_INPUT_ENABLE – Private Hold: PRIVATE_HOLD_ENABLE Default Value TALKING_SOFT_KEY_C (For KX-HDV130/KX-HDV230) Value Format INTEGER Description Specifies the display icon of soft key C during a call. Document Version: 2017-07 Administrator Guide...
Page 342 5.3.34 Call Control Settings • Value Range 0: Original • 1: Line • 2: Menu • 3: Blind (Used when performing Blind Transfer) • 4: Flash/Recall • 5: Incoming Log • 6: Outgoing Log • 7: Phonebook • 8: Park (Used when performing Call Park) •...
Page 343 5.3.34 Call Control Settings Description Specifies which types of devices can be used to respond using "Auto Answer". Value Range – 0: Speaker Phone – 1: Headset Default Value AUTO_ANS_DELAY Value Format INTEGER Description Specifies the delay time before "Auto Answer" answers a call. Value Range 0-20 (sec) Default Value...
Page 344: Video Communication Settings (For Kx-Hdv430)
5.3.35 Video Communication Settings (For KX-HDV430) Default Value 5.3.35 Video Communication Settings (For KX-HDV430) DEFAULT_CALL_MODE Value Format INTEGER Description Specifies the default call type when you make a call by going off hook, etc. Value Range • 0: Voice • 1: Video Default Value Web User Interface Reference...
Page 345 5.3.35 Video Communication Settings (For KX-HDV430) • Value Range 0: 128 kbps • 1: 256 kbps • 2: 384 kbps • 3: 512 kbps • 4: 768 kbps • 5: 1024 kbps • 6: 2048 kbps Default Value Web User Interface Reference Bit Rate VIDEO_BIT_RATE_USE Value Format...
Page 346: Network Camera Settings (For Kx-Hdv430)
5.3.36 Network Camera Settings (For KX-HDV430) H264_PAYLOAD Value Format INTEGER Description Specifies the payload size for H.264. Value Range 96–125 Default Value 5.3.36 Network Camera Settings (For KX-HDV430) NWCAMERA_DISPLAY_NAMEx Parameter Name Example NWCAMERA_DISPLAY_NAME1, NWCAMERA_DISPLAY_NAME2, …, NWCAMERA_DISPLAY_NAME16 Value Format STRING Description x=1–16 Specifies the name of the Network Camera to be displayed in the Network Camera viewer.
Page 347 5.3.36 Network Camera Settings (For KX-HDV430) Description x=1–16 Specifies the user ID to connect to the Network Camera. Value Range Max. 32 characters Default Value Empty string NWCAMERA_PASSx Parameter Name Example NWCAMERA_PASS1, NWCAMERA_PASS2, …, NWCAMERA_PASS16 Value Format STRING Description x=1–16 Specifies the password to connect to the Network Camera.
Page 348 5.3.36 Network Camera Settings (For KX-HDV430) Value Range Max. 24 characters Default Value Empty string NWCAMERA_LINK_PHONEm_NUMBERx Parameter Name Example NWCAMERA_LINK_PHONE1_NUMBER1, NWCAMERA_LINK_PHONE1_NUMBER2, …, NWCAMERA_LINK_PHONE5_NUMBER16 Value Format STRING Description m=1–5, x=1–16 Specifies the phone number to use for Network Camera phone number linkage. Value Range Max.
Page 349: Communication Camera Settings (For Kx-Hdv430)
5.3.37 Communication Camera Settings (For KX-HDV430) Value Range 1024–65535 Default Value 1818 NWCAMERA_AUTO_CLOSE_ENABLE Value Format BOOLEAN Description Specifies whether to disconnect the network camera when the call is ended. Value Range • Y: Disconnect • N: Do not disconnect Default Value NWCAMERA_OPEN_RECEIVE_CALL Value Format BOOLEAN...
Page 350 5.3.37 Communication Camera Settings (For KX-HDV430) COMM_CAMERA_RINGTONE_SETTINGx Parameter Name Example COMM_CAMERA_RINGTONE_SETTING1, COMM_CAMERA_RINGTONE_SETTING2, …, COMM_CAMERA_RINGTONE_SETTING16 Value Format INTEGER Description x=1–16 Specifies the ringtone of each Communication Camera. Value Range 1–32 (10: doorbell) Default Value Web User Interface Reference Ringtone [ 1 - 32 ] DTMF_CONTROL_UP_CAMERAx Parameter Name Example DTMF_CONTROL_UP_CAMERA1, DTMF_CONTROL_UP_CAMERA2, …,...
Page 351 5.3.37 Communication Camera Settings (For KX-HDV430) DTMF_CONTROL_RIGHT_CAMERAx Parameter Name Example DTMF_CONTROL_RIGHT_CAMERA1, DTMF_CONTROL_RIGHT_CAMERA2, …, DTMF_CONTROL_RIGHT_CAMERA16 Value Format STRING Description x=1–16 Specifies the DTMF value for panning the camera right for each Communication Camera. Value Range Max. 8 digits (0–9, *, #) Default Value DTMF_CONTROL_OPEN_CAMERAx Parameter Name Example...
Page 352: Logging Settings
5.3.38 Logging Settings DTMF_CONTROL_VOICE_CAMERAx Parameter Name Example DTMF_CONTROL_VOICE_CAMERA1, DTMF_CONTROL_VOICE_CAMERA2, …, DTMF_CONTROL_VOICE_CAMERA16 Value Format STRING Description x=1–16 Specifies the DTMF value for talking with the camera for each Communication Camera. Value Range Max. 8 digits (0–9, *, #) Default Value 5.3.38 Logging Settings SYSLOG_ADDR Value Format STRING...
Page 353 5.3.38 Logging Settings Value Range 0–6 Default Value LOGGING_LEVEL_SIP Value Format INTEGER Description Specifies the log level of SIP. Value Range 0–6 Default Value LOGGING_LEVEL_TR069 Value Format INTEGER Description Specifies the log level of TR-069. Value Range 0–6 Default Value LOGGING_LEVEL_STUN Value Format INTEGER...
Page 354: Twamp Settings
5.3.39 TWAMP Settings Default Value 5.3.39 TWAMP Settings TWAMP_ENABLE Value Format BOOLEAN Description Specifies whether to enable the TWAMP server function. Value Range Y: Enable the TWAMP server function. N: Disable Default Value Web User Interface Reference Enable TWAMP TWAMP_CONTROL_PORT Value Format INTEGER Description...
Page 355 5.3.39 TWAMP Settings Web User Interface Reference Wait Time for Reflector TWAMP_PADDING_ZERO Value Format BOOLEAN Description Specifies the packet padding for the TWAMP test session. Value Range Y: All zeros N: Random Default Value Document Version: 2017-07 Administrator Guide...
Page 356 5.3.39 TWAMP Settings Administrator Guide Document Version: 2017-07...
Page 357: Useful Telephone Functions
Section 6 Useful Telephone Functions This section explains phone number settings, dial plan settings, the phonebook import/export function, the Broadsoft XSI function, the BroadCloud (Presence) function and Pairing (Parallel Mode). Document Version: 2017-07 Administrator Guide...
Page 358: Phonebook Import And Export
6.1 Phonebook Import and Export 6.1 Phonebook Import and Export This section explains how to import and export phonebook data. Phonebook data of the unit includes names and phone numbers. Phonebook data on the unit can be exported, edited with editor tools, and imported again. In addition, phonebook data created with other software can be imported into the unit.
Page 359 6.1 Phonebook Import and Export Importing the Same Phonebook Data to other Units You can export the phonebook data created on a unit to a PC, and then import it into other units. You can also import phonebook data created on a PC to other units. Import/Export File Format The file format used for importing and exporting the phonebook data is "TSV".
Page 360: Import/Export Operation
6.1.1 Import/Export Operation Phonebook Data in Text Format Aaron MacDowel 1234001 Barbara Nicolls 1234002 Carl O’Brien 1234003 Dorothy Parker 1234004 ···· ···· ···· ···· ···· ···· ···· ···· ···· ···· ···· ···· ···· ···· ···· ···· ···· ···· Record ID (Unique ID: 1–500) Name (up to 24 characters) Reserved (up to 24 characters) Phone number (up to 32 digits)
Page 361: Editing With Microsoft Excel
6.1.2 Editing with Microsoft Excel Note • Depending on the security settings of your Web browser, pop-up menus might be blocked. If the file cannot be exported successfully, try the export operation again or change the security settings of your Web browser. Click Save on File Download window.
Page 362 6.1.2 Editing with Microsoft Excel Select All Files for the file type, select the exported phonebook data file, and click Open. On the Text Import Wizard - Step 1 of 3 window, click Next. Note • Regardless of what is selected for File origin, the file will be processed normally if the format is appropriate.
Page 363: Exporting Data From Microsoft Outlook
6.1.3 Exporting Data from Microsoft Outlook On the Text Import Wizard - Step 3 of 3 window, select all columns in Data preview, select Text in Column data format, and then click Finish. The TSV file will be opened. Note •...
Page 364: Dial Plan
6.2 Dial Plan On the Export to a File window, click Next. Click Map Custom Fields. Clear all items in the To list by clicking Clear Map. Then, drag only Last Name and Business Phone from the From list to the To list, and click OK. On the Export to a File window, click Finish.
Page 365 6.2.1 Dial Plan Settings Element Available Value Description String 0–9, [, -, ], <, :, >, *, You can enter dial plan descriptions using a combination of the #, !, S, s, T, t, X, x, ., characters listed as available values. |, + Digit 0–9, *, #, +...
Page 366 6.2.1 Dial Plan Settings Note • You can enter up to 1000 characters in [Dial Plan]. • You can assign up to 100 dial plans separated by "|" in [Dial Plan]. • You can assign up to 32 digits per dial plan in [Dial Plan]. •...
Page 367: Flexible Keys (For Kx-Hdv230/Kx-Hdv330/Kx-Hdv430)
6.3 Flexible Keys (For KX-HDV230/KX-HDV330/KX-HDV430) • If the dialed phone number is "0011", "1011" and so on when [Call Even If Dial Plan Does Not Match] is set to [No], the call is denied. 6.3 Flexible Keys (For KX-HDV230/KX-HDV330/ KX-HDV430) You can customize the flexible keys on the unit.
Page 368 6.3 Flexible Keys (For KX-HDV230/KX-HDV330/KX-HDV430) Button Description Lamp Indication Used to log in or log out of a group Off: Logged in when ACD (Automatic Call Red on: Logged out Distribution) is enabled. Note • It is necessary to set the ACD feature to enable (→...
Page 369 6.3 Flexible Keys (For KX-HDV230/KX-HDV330/KX-HDV430) Button Description Lamp Indication Simultaneous Enables parallel ringing. Up to 10 Off: Simultaneous Ring off Ring locations can be specified to ring Blue on: Simultaneous Ring on simultaneously when you receive a call. Note • It is necessary to set the XSI feature to enable (→...
Page 370: Settings Using Web User Interface Programming
6.3.1 Settings using Web User Interface Programming Button Description Lamp Indication Group Call Used to answer a group call as a Pickup representative. Network Used to connect to a Network Camera (For Camera. KX-HDV430) Presence Used to confirm the current status of the extension assigned to the key.
Page 371 6.3.1 Settings using Web User Interface Programming Parameter 1 Parameter 2 Button Description Value Description Value Hoteling (Hospitality) Transfer Phone Number Up to 32 digits Blind Transfer Phone Number Up to 32 digits Conference Phone Number Up to 32 digits Directed Call Pickup Phone Number Up to 32 digits...
Page 372: Settings Using Configuration File Programming
6.3.2 Settings using Configuration File Programming • Button 1 is set to log in and log out of an ACD group on line 6. • Buttons 2, 6 and 10 are set to show the status of a certain extension. They can also be used to call that extension and transfer calls to it.
Page 373 6.3.2 Settings using Configuration File Programming Parameter 1 Parameter 2 Value Value 1 Value 2 Note X_PANASONIC_IPTEL_ 1 (Local Category The search by name screen is PHONEBOOK Phonebook) Number (1–9) displayed when value 2 is "0" or "None". 2 (Remote Phonebook) 0 or None (Select...
Page 374: Broadsoft Xsi (Xtended Services Interface)
6.4 Broadsoft XSI (Xtended Services Interface) Parameter 1 Parameter 2 Value Value 1 Value 2 Note X_PANASONIC_IPTEL _APPLICATION X_PANASONIC_IPTEL_ User ID PRESENCE (Up to 128 digits) X_PANASONIC_IPTEL_ MYPHONE 6.4 Broadsoft XSI (Xtended Services Interface) 6.4.1 Outline BroadWorksXsi is an API library used to support the integration of Internet service-based BroadWorks functionality to create web applications and mashups (web application hybrids).
Page 375: Xsi Service Settings
6.4.2 XSI Service Settings * When Feature Key Synchronization is set (FWD_DND_SYNCHRO_ENABLE_n="Y", see page 336), the Do Not Disturb function will not operate as an XSI function. (7) Anonymous Call Rejection The Anonymous Call Rejection function rejects calls made to the IP phone as Anonymous Calls. 6.4.2 XSI Service Settings Phone settings for using XSI services can be set using configuration parameters or the Web user interface (administrators only).
Page 376: Broadcloud (Presence)
Tap "Call Settings" → "Remote Office", "Anywhere", "SimultaneousRing", "Anonymous Call", or "Block Anonymous". For details, refer to the Operating Instructions on the Panasonic Web site (→ see Introduction). 6.5 BroadCloud (Presence) 6.5.1 Outline This product supports the following BroadCloud functions.
Page 377 6.5.2 BroadCloud (Presence) Function Settings Parameter Name Description Reference XMPP_PORT Specifies the communication port for XMPP. page 244 XMPP_TLS_VERIFY Specifies the TLS (Transport Layer Security) certification page 244 validation type for protocol communication. XMPP_ROOT_CERT_ Specifies the path (URL) of the ROOT certificate for XMPP. page 244 PATH XMPP_CLIENT_CERT...
Page 378 6.5.2 BroadCloud (Presence) Function Settings Administrator Guide Document Version: 2017-07...
Page 379: Firmware Update
Section 7 Firmware Update This section explains how to update the firmware of the unit. Document Version: 2017-07 Administrator Guide...
Page 380: Firmware Server Setup
7.1 Firmware Server Setup 7.1 Firmware Server Setup No special server is necessary for the firmware update. You can use an HTTP, HTTPS, FTP, or TFTP server as the firmware server by simply setting its URL. Note • This feature is available only in IPv4 mode. •...
Page 381 7.3 Executing Firmware Update The firmware update process Note • Downgrading the firmware is not recommended. Operation cannot be guaranteed after performing a downgrade. Step 1 The unit downloads a configuration file from the provisioning server. • For details about setting the timing of when configuration files are downloaded, see 2.2.4 Downloading Configuration Files.
Page 382: Upgrade Firmware (For Kx-Hdv130/Kx-Hdv230)
When an updated version of the firmware is provided on a Web site or other means, you can perform the firmware update manually using Web user interface programming. For details about the manual firmware update, see 4.7.3 Upgrade Firmware (For KX-HDV130/ KX-HDV230).
Page 383: Troubleshooting
Section 8 Troubleshooting This section provides information about troubleshooting. Document Version: 2017-07 Administrator Guide...
Page 384: Troubleshooting
8.1 Troubleshooting 8.1 Troubleshooting If you still have difficulties after following the instructions in this section, disconnect the unit from the AC outlet, then connect the AC adaptor again. If using PoE, disconnect the LAN cable, then connect the LAN cable again.
Page 385 8.1 Troubleshooting Making/Answering Calls, Intercom Problem Cause/Solution The unit does not ring. • Check the VoIP status in the Web user interface and confirm that each line is registered properly (→ see To check the setting status in the Web user interface in this section).
Page 386: Error Codes
Check the status displayed. Click [VoIP Status] to check the VoIP settings. Check the status displayed. To check the setting status using the Unit KX-HDV130/KX-HDV230 [ ]/[ ]: System Settings → [ ]/[ ]: Status → Administrator Guide Document Version: 2017-07...
Page 387 Note KX-HDV330/KX-HDV430 To check the setting status using the Unit [In standby mode] → System Settings. Tap Status. Export Logging File Export the log file using the Web user interface (see 4.7.4 Export Logging File). Document Version: 2017-07 Administrator Guide...
Page 388 Panasonic Corporation 1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8501, Japan © Panasonic Corporation 2017 PNQX8471YA PM0417SM1067...

This manual is also suitable for:

Kx-hdv430 Kx-hdv230 Kx-hdv330

Panasonic KX-HDV130 Manual

1 Initial Setup

2 General Information on Provisioning

3 Phone User Interface Programming

4 Web User Interface Programming

5 Configuration File Programming

6 Useful Telephone Functions

7 Firmware Update

8 Troubleshooting

Quick Links

Administrator Guide

SIP Phone

Troubleshooting

Related Manuals for Panasonic KX-HDV130

Summary of Contents for Panasonic KX-HDV130