Page 1
micro DM-100 p. 105 p. 125 p. 145 p. 165 p. 185 p. 205 p. 225 p. 247 p. 267 p. 287 p. 307 p. 327 p. 349 p. 369 p. 389 p. 409 p. 433 RIDGE TOOL COMPANY...
Page 3
Failure to understand and follow the contents of this manual may result in micro DM-100 Digital Multimeter electrical shock, re and/or Record Serial Number below and retain product serial number which is located on nameplate. serious personal injury.
DM-100 Digital Multimeter Table of Contents Table of Contents ........................... 2 Safety Symbols ..........................3 General Safety Rules ........................3 Work Area Safety .......................... 3 Electrical Safety ..........................3 Personal Safety ..........................3 Equipment Use and Care ......................4 Service ..............................
DM-100 Digital Multimeter Safety Symbols In this operator’s manual and on the product, safety symbols and signal words are used to communicate important safety information. This section is provided to improve under- standing of these signal words and symbols.
WARNING This section contains important safety information that is speci c to this tool. Read these precautions carefully before using the RIDGID® micro DM-100 Digital Multimeter to reduce the risk of electrical shock or other serious injury. SAVE THESE INSTRUCTIONS! Keep this manual with the tool for use by the operator.
Description, Specifications And Standard Equipment Description The RIDGID® DM-100 Digital Multimeter is a handheld instrument. The unit can measure DC and AC Voltage and Current, Resistance, Capacitance, Frequency, Temperature, Continuity (audible signal) and Test Diodes. The multimeter can automatically select the best range for measurement.
Page 8
DM-100 Digital Multimeter Input Limits Function Maximum Input Voltage V DC/AC 1000 V DC/AC Current mA DC/AC 400 mA DC/AC Current A DC/AC 10 A DC/AC Frequency, Duty Cycle 600 V DC/AC Accuracy is given at 18°C to 28°C (65°F to 83°F), less than 70% RH...
Page 9
DM-100 Digital Multimeter Resistance (Autoranging) Range Resolution Accuracy 400.0 Ω 0.1 Ω ±1.2% of Reading ± 4 Digits 4.000 kΩ 1 Ω ±1.0% of Reading ± 2 Digits 40.00 kΩ 10 Ω 400.0 kΩ 100 Ω ±1.2% of Reading ± 2 Digits 4.000 MΩ...
Test Current ............< 0.3 mA Overload protection ........600V DC or AC RMS Standard Equipment The RIDGID® micro DM-100 Digital Multimeter comes with the following items: • micro DM-100 Digital Multimeter • Terminal Plugs • Test Leads with Covers, Black and Red •...
DM-100 Digital Multimeter Icons Screen Icons Icon Number Icons on Screen Description Low Battery. — Polarity Indicator. Negative readings, In relative mode, this sign indicates that the present input is less than the stored reference value. Alternating Current or Voltage.
Changing/Installing Batteries The RIDGID DM-100 Digital Multimeter is supplied without the battery installed. When the low battery [ ] icon appears on the display screen, replace the battery. Operating the multimeter with a low battery can cause incorrect readings.
DM-100 Digital Multimeter 1. Switch OFF the device and disconnect Battery Compartment test leads. Cover 2. Use a Phillips head screwdriver to loosen the battery compartment cover screws and remove the cover. Remove existing battery. 3. Install 9V alkaline battery (NEDA 1604,...
DM-100 Digital Multimeter Set-Up and Operation WARNING Set up and operate the Multimeter according to these proce- dures to reduce the risk of injury from electric shock and other causes, and prevent tool damage. Use caution when working with voltages above 30 V AC RMS, 42 V AC peak or 60 V DC.
DM-100 Digital Multimeter have selected, change to a higher range. On some low DC and AC voltage ranges, with the test leads not connected to a device, the display may show a random, changing reading. This is normal and is caused by the high-input sensitivity. The reading will stabilize and give a proper measurement when connected to the circuit.
DM-100 Digital Multimeter Pushbuttons Mode Button (MODE) The Mode Button is used to select Ohms/Diode/Continuity or DC/AC current in the appro- priate rotary switch settings. Range Button (RANGE) When the meter is turned on, it automatically goes into Autoranging. This automatically selects the best range for the measurement being made and is generally the best mode for most measurements.
DM-100 Digital Multimeter 1. Set the function switch to the V DC/AC ( ) position and use the MODE button to select AC or DC. 2. Insert the black test lead plug into the “COM” terminal and the red test lead plug into the “V”...
DM-100 Digital Multimeter 2. Insert the black test lead plug into the “COM” terminal and the red test lead plug into the “Ω” terminal. 3. Touch the test probe tips across the circuit or part under test. It is good practice to disconnect one side of the part under test so the rest of the circuit will not interfere with the resistance reading.
DM-100 Digital Multimeter Capacitance Measurement To reduce risk of electric shock, disconnect all power (remove batteries, WARNING unplug cord, discharge all capacitors, etc.) to the circuit being measured before taking any capacitance measurement. Use the DC Voltage function to con rm that the capacitor is discharged.
Calibration The calibration of the meter should be checked once a year to ensure that it performs ac- cording to the speci cations. Take to a RIDGID Service Center for calibration check. Fuse Replacement If when measuring current the display shows zero, the fuse(s) may need to be changed.
Fuse F500mA/1000V fast blow for 400mA range 44763 Fuse F10A/1000V fast blow for 10A range Further information on accessories speci c to this tool can be found in the RIDGID Catalog and online at www.RIDGID.com or www.RIDGID.eu Storage The RIDGID micro DM-100 Digital Multimeter must be stored in a dry secure area between -20°C to 60°C (-4°F to 140°F) and humidity less than 80% RH.
DM-100 Digital Multimeter Troubleshooting SYMPTOM POSSIBLE REASON SOLUTION Meter does not work Fuse not properly Check the fuse, insert properly. inserted. properly. Battery low on power. Replace battery. Meter needs calibration. Send the unit for calibration to the RIDGID Independent Authorized Service Center.