Page 1
Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http:// www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right corner of our website.
Page 2
Thank you for choosing ViewSonic As a world leading provider of visual solutions, ViewSonic is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity. At ViewSonic, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic product you have chosen will serve you well.
Compliance Information Please read before proceeding • Use only the batteries and power adapter provided by the manufacturer. The use of unauthorized accessories may void your warranty. • Do not store your device in temperatures higher than 50°C (122°F). • The operating temperature for this device is from 0°C (32°F) to 35°C (95°F). FCC Notice The following statement applies to all products that have received FCC approval.
FCC SAR Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Proposed Maximum Substance...
Serial Number: Purchase Date: Product disposal at end of product life ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more. USA & Canada: http://www.viewsonic.com/company/green/recycle-program/ Europe: http://www.viewsoniceurope.com/eu/support/call-desk/...
Contents Compliance Information Please read before proceeding ................i FCC Notice ......................i FCC SAR Information ....................ii CE Conformity for European Countries ..............ii Following information is only for EU-member states: ..........ii European Union Regulatory Conformance............ii Declaration of RoHS2 Compliance ............... iii Copyright Information Product Registration .....................iv For Your Records ....................iv Packaged Items...
Page 8
Troubleshooting The stylus pen does not work ................18 The finger touch operation does not work ............18 Lines traced with the stylus pen do not match screen .........18 You can check the installation condition of the camera unit when the troubleshooting in the EyeRIS setup menu is displayed on ........19 Windows Operating System Version ..............20 Specifications Customer Support...
Packaged Items Make sure your box contains everything listed. If any pieces are missing, contact your dealer. • Camera unit x 1 • Laser Module unit x1 • Adapter • Quick start Guidel x 1 • Screw (T3 x 15) x 2 •...
Part names of the supplied stylus pen LED indicator Charging jack (Mini USB) Charging Stylus Please use the Stylus charging cable and connect the charging jack of Stylus to a USB port on a computer and Stylus will start charging; it takes approximately 3 minutes to charge Stylus.
Page 12
Disclaimer: meters. ViewSonic Corporation shall not be liable for technical or editorial reeors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this meterial, or the performance or use of this product. In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specifications without notice.
Page 14
6.2 Red Laser flatness calibration steps: 6.2.1 Adjust Gear B; make the distance between the two points b / c in the image below and the whiteboard parallel. 6.2.2 Adjust Gear A, check and make sure that the distance between the two points b / c and the whiteboard is 6±1.5mm.
Operating Environment / EyeRIS Supported OSs are as follows Windows 7, Windows 8/8.1 and above • For starting up the software, Microsoft .NET Framework 4 or later is required. Download the Microsoft .NET Framework from the website of Microsoft and install it onto the computer.
Page 16
1. Download the software Access to our projector support page in our website with the below URL: HTTP://www.viewsonic.com/support/ Find the software for the IWB Setup Software, EyeRIS, download and install it onto the computer according to the displayed instructions. 2. Double click [EyeRIS_3.0.6.21_20160517_ViewSonic.msi] The Setup window is displayed.
Page 17
5. Click [Next>]. After that, follow the displayed instructions to complete installation. When the installation is complete,EyeRIS and SensorViewer icon is added to the desktop.
How to uninstall the software 1. Click [Control Panel] in the start menu, and double-click [Add or Remove Programs]. 2. Right-click [EyeRIS] and click [Uninstall] in the list. After that, follow the displayed instructions to complete uninstallation. 3. When uninstallation is completed properly, reboot the computer.
Startup the Software Preparation: • First of all, perform setup according to the user’s manual supplied with the projector or the installation manual supplied with the Interactive White Board Kit or the Touch Module. • If the computer and the camera unit are not connected by a USB cable, the message at right would be displayed on and the software would not be started 1.
Calibration Menu Display Indicate status of the stylus pen or the finger touch operation. [Calibrated] The stylus pen or the finger touch operation is ready to use [Not calibrated] Cannot use the stylus pen or the finger touch operation because calibration is not performed, or the trouble shooting is displayed on Indicate Close EyeRIS Setup Menu.
Performing Calibration Before starting to use the stylus pen or the Touch Module, make sure to perform calibration in order to make the computer to recognize exact position touched by the stylus pen or a finger. Start Manual Automatically calibrate the stylus pen position. Recommend this when simple calibration is preferred.
Perform Calibration Automatically [Automatic Calibration] Click the [Start Automatic] button on the displayed calibration menu. Projected image on the screen will be switched to the Automatic Calibration Screen After five to eight seconds, calibration will be completed and the screen will return to display the projected image.
Perform Calibration Manually [Manual Calibration] 1. Click [Start Manual] button on the displayed calibration menu. Projected image on the screen is switched to the Manual Calibration Screen and red dot is indicated at the top left on the screen. 2. Press the center of the red dot with the stylus pen. The red dot is indicated at 25 points in order on the screen.
Page 24
3. Touch icon in the task tray by the stylus pen. This message is popped up when calibration is completed properly. 4. In order to align EyeRIS more precisely with visual aid, click on Power button to exit EyeRIS U I and Open "Sensor Viewer"application to physically align EyeRIS module with Projection area.
Page 25
Troubleshooting Tips: If the Projection area is not visible due to high ambient light, try reducing and click "Confirm" to adjust to the reduced or increased exposure settings. Please note that this adjustment is just to confirm that projection area is fully covered by EyeRIS sensor and has no correlation with the working of EyeRIS.
Troubleshooting The stylus pen does not work • Have the driver and the calibration software been installed on the computer? • Is the USB cable connected between the computer (type A USB port) and the camera unit (type Mini USB port)? •...
You can check the installation condition of the camera unit when the troubleshooting in the EyeRIS setup menu is displayed on • Troubleshooting screen Change the stylus pen status. Switch to the If clicking / pressing calibration menu this by the mouse / the stylus pen when PAUSE Enable/disable the CALIBRATION is indicated...
Windows Operating System Version CNY EyeRIS Intellispace 3.1.7_022 supported supported Windows 8.1 Windows 8.1 Windows 8.1 Pro Windows 8 Windows 8 Windows 8 Pro Windows 8 OEM Windows 7 Home Premium Windows 7 Professional Windows 7 Windows 7 Enterprise Windows 7 Ultimate Windows 10 Home Windows 10 Windows 10 Pro...
® What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Page 32
Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: 1. Damage to other property caused by any defects in the product, damages based...
Page 33
Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: 1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.
Page 34
Tel: (52) 999-925-1916 Tel: 01(52)95-15-15-22-22 E-Mail: rrrb@sureste.com Fax: 01(52)95-15-13-67-00 E-Mail. gpotai2001@hotmail.com Tijuana: FOR USA SUPPORT: ViewSonic Corporation Av Ferrocarril Sonora #3780 L-C 14035 Pipeline Ave. Chino, CA 91710, USA Col 20 de Noviembre Tel: 800-688-6688 (English); 866-323-8056 (Spanish); Tijuana, Mexico E-Mail: http://www.viewsonic.com...