Related Manuals for Cactus 602 SERIES
Summary of Contents for Cactus 602 SERIES
- Page 1 Cactus Technologies, Limited -602 Series Industrial Grade SATA SSD Product Manual April 1, 2011 Corporate Headquarters Suite C, 15/F, Capital Trade Center 62 Tsun Yip Street, Kwun Tong Kowloon, Hong Kong...
- Page 2 Cactus products are not designed, intended or authorized for use as components in systems intended for surgical implant into the body or in other applications intended to support or sustain life or for any application where the failure of a Cactus product can result in personal injury or death.
-
Page 3: Table Of Contents
Cactus Technologies, Limited Table of Contents 1.Introduction to Cactus Technologies -602 Series Industrial Grade SATA SSD Products .........4 1.1.Supported Standards...........................5 1.2.Product Features............................5 1.2.1.Host and Technology Independence....................5 1.2.2.Defect and Error Management......................5 1.2.3.Power Supply Requirements......................6 2.Product Specifications..............................6 2.1.System Environmental Specifications......................6 2.2.System Power Requirements........................6 2.3.System Performance...........................7 2.4.System Reliability............................7... -
Page 4: Introduction To Cactus Technologies -602 Series Industrial Grade Sata Ssd Products
• Voltage support: 5.0V±10% The Cactus Technologies -602 Series SATA Solid State Drive(SSD) is a high capacity solid- state flash memory product that complies with the Serial ATA 2.6 standard and is functionally compatible with a SATA hard disk drive. Cactus -602 Series SATA SSDs provide up to 128GB of formatted storage capacity in 2.5”... -
Page 5: Supported Standards
The soft error rate for Cactus Technologies -602 Series Industrial SATA SSDs is much lower than that of magnetic disk drives. In the extremely rare case where a read error does occur, the drive has sophisticated ECC to recover the data. -
Page 6: Power Supply Requirements
Cactus Technologies -602 Series Industrial SATA SSDs unparalleled reliability. 1.2.3. Power Supply Requirements Cactus Technologies -602 Series Industrial SATA SSD operates at a voltage range of 5.00 volts ± 10%. 2.Product Specifications For all the following specifications, values are defined at ambient temperature and nominal supply voltage unless otherwise stated. -
Page 7: System Performance
< 1 non-recoverable error in 10 bits READ Endurance: > 2,000,000 erase/program cycles 2.5. Physical Specifications The following sections provide the physical specifications for Cactus Technologies -602 Series Industrial SATA SSD products. Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4... -
Page 8: 2.5" Sata Ssd Physical Specifications
Cactus Technologies, Limited 2.5.1. 2.5” SATA SSD Physical Specifications Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4... - Page 9 Cactus Technologies, Limited Figure 2-1. 2.5” SATA SSD Dimensions Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4...
-
Page 10: 1.8" Sata Ssd Physical Specifications
Cactus Technologies, Limited 2.5.2. 1.8” SATA SSD Physical Specifications Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4... -
Page 11: Interface Description
Cactus Technologies, Limited 3. Interface Description The following sections provide detailed information on the Cactus Technologies -602 Series Industrial SATA SSD interface. 3.1. SSD Pin Assignments and Pin Type Cactus -602 Series SATA SSD uses industry standard 7+12 connector. The signal/pin assignments are listed in Table 3-5. -
Page 12: Electrical Specification
Active 3.3.3. AC Characteristics Cactus -602 Series SATA SSD products conforms to all AC timing requirements as specified in the Serial ATA specifications. Please refer to that document for details of AC timing for all operation modes of the device. -
Page 13: Ata Drive Register Set Definition And Protocol
Bit 0 (AMNF) This bit is set in case of a general error. 4.1.3. Feature Register This register provides information regarding features of the SSD that the host can utilize. Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4... -
Page 14: Sector Count Register
Bit 0 (HS0) When operating in the Cylinder, Head, Sector mode, this is bit 0 of the head number. It is Bit 24 in the Logical Block Address mode. Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4... -
Page 15: Status Registers
The Interrupt Enable bit enables interrupts when the bit is 0. When the bit is 1, interrupts from the drive are disabled. This bit is set to 0 at power on and Reset. Bit 0 This bit is ignored by the drive. Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4... -
Page 16: Drive Address Register
Bit 0 (-nDS0) This bit is 0 when the drive 0 is active and selected. 5.ATA Command Description This section defines the ATA command set supported by the Cactus -602 Series SATA SSDs. 5.1. ATA Command Set Table 5-7 summarizes the supported ATA command set . - Page 17 D—only the drive parameter is valid and not the head parameter. Note: 1. For SATA drives, the drive number is always 0. Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4...
-
Page 18: Identify Drive-Ech
MWDMA mode. 0007H 0003H Advanced PIO modes supported (modes 3 and 4) 0078H Minimum MWDMA cycle time per word is 120ns. 0078H Recommended MWDMA cycle time is 120ns. Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4... - Page 19 Master password revision code XXXXH COMRESET result 80FEH Acoustic management values 95-99 0000H Reserved 100-103 XXXXH Maximum user LBA for 48-bit addressing mode. 104-127 0000H Reserved XXXXH Security status 129-255 Reserved Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4...
- Page 20 (1) 8GB 2.5” SATA SSD ---------------------------------------------------------- KD8GF-602S (2) 8GB 2.5” SATA SSD Extended Temp ------------------------------------ KD8GFI-602S (3) 8GB 1.8” SATA SSD ---------------------------------------------------------- KD8GF-602SA (4) 128GB 2.5” SATA SSD -------------------------------------------------------- KD128GFT-602S Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4...
- Page 21 B.1.Direct Cactus Technical Support Cactus Technologies Limited Suite C, 15/F, Capital Trade Center 62 Tsun Yip Street, Kwun Tong Kowloon, Hong Kong Tel: +852-27972261 Fax: +852-27973777 Email: tech@cactus-tech.com Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4...
- Page 22 Appendix C.Cactus Worldwide Sales Offices Cactus Technologies Limited Suite C, 15/F, Capital Trade Center 62 Tsun Yip Street, Kwun Tong Kowloon, Hong Kong Tel: +852-27972277 Fax: +852-27973777 Email: sales@cactus-tech.com Cactus Technologies Limited -602 Series Industrial Grade SATA SSD Product Manual v1.4...
- Page 23 Appendix D.Limited Warranty I. WARRANTY STATEMENT Cactus Technologies warrants its Industrial Grade products only to be free of any defects in materials or workmanship that would prevent them from functioning properly for five years from the date of purchase. This express warranty is extended by Cactus Technologies Limited to customers of our products.
- Page 24 Technologies Customer Service department (tech@cactus-tech.com) with the following information: product model number and description, nature of defect, conditions of use, proof of purchase and purchase date. If approved, Cactus Technologies will issue a Return Material Authorization or Product Repair Authorization number. Ship the defective product...