Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Baumatic B6FS
Summary of Contents for Baumatic B6FS
- Page 2 PREFACE Dear Customer, Congratulations on purchasing your new product from Home Appliances. To register your Parts and Labour Warranty, some conditions apply, please refer to your warranty card for more details and contact our After Sales Support team on: 1800 444 357 and Select 1 Our Customer Care Centre is there to ensure you get the most out of your appliance.
- Page 3 DESCRIPTION OF THE HOT PLATES B6FS MODEL: NATURAL U-LPG 1 Wok burner 13.5 MJ/h 11.4 MJ/h 2 Rapid gas burner 12.0 MJ/h 10.4 MJ/h 3 Semi rapid gas burner 7.1 MJ/h 6.3 MJ/h 4 Auxiliary gas burner 4.1 MJ/h 3.6 MJ/h...
- Page 4 1) BURNERS Burners Power ratings Pan Ø in cm NATURAL ULPG A diagram is screen-printed above each knob on the front panel. This diagram indicates to which burner Ultra rapid 13.5 MJ/h 11.4 MJ/h 22 ÷ 24 the knob in question corresponds. After having Rapid 12.0 MJ/h 10.4 MJ/h 20 ÷...
- Page 5 WARNINGS AND ADVICE FOR THE USER: - use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by activating the mechanical aeration device (suction hood or electric fan fig.
-
Page 6: Care And Maintenance
CLEANING IMPORTANT: - Do not force the taps if they are difficult to open or close. Contact the technical always disconnect the appliance from the gas assistance service for repairs. and electricity mains before carrying out any - Don’t use steam jets for cleaning the hotplate. cleaning operation. -
Page 7: Installation
INSTALLATION TECHNICAL INFORMATION FOR construction shall be within 450 mm above the top INSTALLATION PERSONNEL of the burner. A minimum depth of 70 mm from the top of the worktop surface must be provided for the This appliance shall be installed only appliance. -
Page 8: Maintenance Schedule
INSTALLATION 4) FIXING THE HOT PLATE withstanding the appliance temperatures. Ensure that the supply connection point is accessible with The hot plate has a special seal which prevents the appliance installed. To facilitate the shield may liquid from infiltrating into the cabinet. Strictly need to be removable. -
Page 9: Gas Connection
INSTALLATION 5) GAS CONNECTION Natural Gas The gas connection is located in the rear and on the Natural Gas installations require the connection of a underside of the appliance 118 mm (for 60 cm), gas regulator at the appliance. This regulator is 165 mm (for 70 cm), 255 mm (for 90 cm) from the supplied with the appliance on purchase. -
Page 10: Electrical Connection
INSTALLATION 6) ELECTRICAL CONNECTION Letter N (neutral) = blue wire; Earth symbol = green - yellow wire. IMPORTANT: the appliance must be installed - The power supply cable must be positioned so that no following the manufacturer's instructions. The part of it is able to reach an overtemperature of 90 °C. manufacturer will not be liable for injury to - Never use reductions, adapters of shunts for persons or animals or property damage caused... - Page 11 ADJUSTMENTS Always disconnect the appliance from the 7) TAPS electricity main before making any adjustments. Our taps are suitable for all the gas, they are male All seals must be replaced by the technician at conical type at one way. the end of any adjustments or regulations.
- Page 12 CONVERSIONS 8) U-LPG GAS TO NATURAL GAS 9) NATURAL GAS TO U-LPG GAS CONVERSION PROCEDURE CONVERSION PROCEDURE Appliance models: Gas stainless steel hotplate Appliance models: Gas stainless steel hotplate models: models: 4 Burners 4 Burners 5 Burners 5 Burners 1. Remove each burner cap and burner skirt. 1.
-
Page 13: Replacing The Injectors
CONVERSIONS paragraphs 7. The technician must reset any 10) REPLACING THE INJECTORS seals on the regulating or pre-regulating The burners can be adapted to different types of devices. gas by mounting injectors suited to the type of gas The envelope with the injectors and the labels in question. - Page 14 SERVICING CABLE TYPES AND SECTIONS TYPE OF TYPE OF SINGLE - PHASE HOT PLATE CABLE POWER SUPPLY Gas hot plate H05 RR - F Section 3 x 0.75 mm ATTENTION!!! If the power supply cable is replaced, the installer should leave the ground wire longer ( B) than the phase conductors (fig.
-
Page 15: Technical Assistance And Spare Parts
TECHNICAL ASSISTANCE AND SPARE PARTS Before leaving the factory, this appliance will have been tested and regulated by expert and specialized personnel in order to guarantee the best performances. Any repairs or adjustments which may be subsequently required may only be carried out by qualified personnel with the utmost care and attention.