Related Manuals for Samsung LH015I SERIES
Summary of Contents for Samsung LH015I SERIES
-
Page 1: Led Display
Ver. 2.1 LED Display Installation Manual LH015I ***** (P1.5) LH020I ***** (P2.0) LH025I ***** (P2.5) Samsung Electronics LED Display Installation... -
Page 2: Table Of Contents
1-6 Accessary [Components] 2. How to install 2-1 How to handle (warning/caution) 2-2 Installation Requirements 2-3 Physical Installation 2-4 Data cabling 2-5 Power cabling 3. Example of Installation Feature 4-1 PC Control Program 4-2 LED Color correction Samsung Electronics LED Display Installation... -
Page 3: Specification
- High brightness product for Indoor display(1.5mm/2.0mm 800nit, 2.5mm 2000nit) - Various sizes of screen configuration : Users can configure multiple size of screen by LED cabinet unit [Leeum, Samsung Museum of Art, P1.5 8x4] Samsung Electronics LED Display Installation... -
Page 4: Specification
- Able to adjust picture quality (Brightness, Contrast, etc.,) - Support HDBT input and output for long distance video signals and control transmission - Various input port : DP, HDMI, DVI, USB, RJ45 LED Signage BOX LED Display Samsung Electronics LED Display Installation... - Page 5 Brightness (max) 800nits 800nits 2,000nits Min : 25% of max 3,000:1 3,000:1 5,000:1 Brightness Level 15.5bit 15.5bit 15.5bit Power Consumption 210W 210W 150W Name of Work Temp 0~40℃ 0~40℃ 0~40℃ FHD Size 133.1”(3x6) 173.5”(4x8) 216.8”(5x10) Samsung Electronics LED Display Installation...
- Page 6 3 x 6 (18 units) 1 unit (Pitch 1.5) LH020I***** 4 x 8 (32 units) 1 unit (Pitch 2.0) LH025I***** 5 x 10 (50 units) 1 unit (Pitch 2.5) SBB-IS08E Reference Picture (LED Signage Box) Samsung Electronics LED Display Installation...
-
Page 7: Dimension Spec
1. Specification 1-3 Dimension spec (unit : mm) [except the depth of LED ] P1.5/P2.0: 0.6mm P2.5 : 1.0mm Samsung Electronics LED Display Installation... -
Page 8: Exploded View
6 COVER HANDLE 7 COVER FRAME TOP 8 COVER FRAME BOTTOM 9 ASSY BRACKET P-FRONT 9.1 BRAKET-FRONT 9.2 INLAY TERMINAL 9.3 HOLDER-WIRE 9.4 HOLDER MAGNET 9.5 MAGNET 10 COVER-TOP BOTTOM LEFT RIGHT 4 11 LED MODULE Samsung Electronics LED Display Installation... -
Page 9: Viewing The Connection
1. Specification 1-5 Viewing the Connection Samsung Electronics LED Display Installation... -
Page 10: Accessary [Components]
1. Specification 1-6 Accessary [Components] Components may vary based on the country. Samsung Electronics LED Display Installation... -
Page 11: How To Install
[Do not let panel face down] ▶ Do not lay the product having the LED Front LED cracked MODULE side as the bottom side after uncovering Front the protection from the product before Lower – Long Samsung Electronics LED Display Installation... - Page 12 When you use magnetic to during the remove the substances, the module may damage be unlocked. So determine whether to remove after separating it or having it attached depending on the attachment status. Samsung Electronics LED Display Installation...
- Page 13 (metal dust) stick to LED surface. LED surface must be cover if display area is under construction 2. Clean dust on the LED surface with Cleaner machine (must use a soft brush head) Soft brush Samsung Electronics LED Display Installation...
- Page 14 - Slowly move it around the metal dust area. - Metal Dust will stick to Magnet Block. - Remove Magnet Block and clean it for next times using. Magnet block Metal Dust Magnet block after removing from LED surface Samsung Electronics LED Display Installation...
-
Page 15: Installation Requirements
2. How to install 2-2 Installation Requirements (Circuit) Samsung Electronics LED Display Installation... - Page 16 2. How to install 2-2 Installation Requirements (Circuit) Static Electricity Precautions Samsung Electronics LED Display Installation...
- Page 17 2. How to install 2-2 Installation Requirements (Circuit) Installation Precautions Samsung Electronics LED Display Installation...
- Page 18 2. How to install 2-2 Installation Requirements (Software) - Desktop or Notebook PC installed with Operating System of below: ∙ Windows 7 32bit/64bit ∙ Windows 8 32bit/64bit - Software ∙ .Net Framework 4.5 or above Samsung Electronics LED Display Installation...
- Page 19 6. Rear clearances : Needs to secure enough space to a worker in all kinds of structure. 7. Local regulations should be considered for each type of Samsung Electronics LED Display Installation...
- Page 20 When the height of a structure is too high, Samsung recommend to install ‘ Cat Walk’ at the rear of set and a lift in the front of set so that workers can work easily in a high area.
- Page 21 - When the structure is installed in a pocket shape, the surrounding temperature should be maintained below 35C degree and it is recommended to make more than 10cm of space from the wall. Samsung Electronics LED Display Installation...
- Page 22 SET to be managed below Max 40℃. Secure space for absorbing air at the back under area of the SET. Secure enough working space and heat rejection area at the back area of the SET. Samsung Electronics LED Display Installation...
- Page 23 2. How to install 2-2 Installation Requirements : Free space behind the Set Door open: 480*540*379mm => FREE SPACE behind Cabinet should be over 300mm for door opening space. Door open Samsung Electronics LED Display Installation...
- Page 24 Open space for Bracket Align 8.0mm Rounded rectangle Hole for handles and hole for SET fixing Hex bolt Vertical frame 90° Free space for Door opening 10.0mm Flat base Rounded rectangle hole for Frame position left-right adjustment Samsung Electronics LED Display Installation...
- Page 25 2. How to install 2-2 Installation Requirements : Tool for Installation LED MODULE JIG Wrench 10.0mm Phillips head crew driver (model name: CY-LJFNAS) socket ratchet Pliers Rubber Flat head crew driver Antistatic hammer Glove Samsung Electronics LED Display Installation...
- Page 26 1) Remove the tape from the upper side of the box, and then open up. 2) Remove the Top–Cushion 3) Take out the set while holding the handle inside the PE-Bag, and then remove the PE-bag * Do not keep the LED display face down to ground Samsung Electronics LED Display Installation...
- Page 27 Use internal pattern to check dead pixel or any damage with screen Internal white pattern : - Turn on Power - Push Source button 5 seconds and release, - Wait for display, push one more times. (color rotation : W -> R-> G -> B) Samsung Electronics LED Display Installation...
- Page 28 (As the sensor area has magnetic Sensor for properties, able to be attached on the Illumination Intensity metallic objects. Illumination Intensity Sensor is included in LED Signage Box accessory) Samsung Electronics LED Display Installation...
- Page 29 Bottom row: side use Stud guide used to guide position between 2 cabinets. (tolerance 0.2mm) - For bottom row use them on side(Left-right) - From the second row use it on Top (refer example picture) Tool : Plier Samsung Electronics LED Display Installation...
- Page 30 - When rubber pad or a bracket is input between bottom of LED module and a cover-frame, it can reduce a gap of module~module by preventing a sagging of LED module. (Refer to the bottom figure and page 70) line lasers line lasers level tool Base Guide side Rubber pad Samsung Electronics LED Display Installation...
- Page 31 From 2 cabinet : Align LED modules of For first cabinet : Align LED module new cabinet with around cabinets with mechanical cabinet LED modules Alignment line Mechanical cabinet Samsung Electronics LED Display Installation...
- Page 32 - Install from bottom to top - Install from center to side - Must align all LED modules after install each cabinet Center column from bottom to top Next column from bottom to top Next column from bottom to top Samsung Electronics LED Display Installation...
- Page 33 2-3 Physical Installation: Remove Protection Material PROTECTION (item : BN63-15047A, COVER-TOP BOTTOM LEFT RIGHT) Cushion Top Put Cabinet on BOX, LED module face up Remove all of the Cover-Protection Keep Cabinet on Cushion Top Tool: screw driver Samsung Electronics LED Display Installation...
- Page 34 2. How to install 2-3 Physical Installation: Base row Fix 1 cabinet to Wall-frame - Check cabinet horizontal alignment - Use M6 screws, Fix 4 points on back side M6 Screw Horizontal alignment is most important Samsung Electronics LED Display Installation...
- Page 35 - Slightly fix 2 cabinet to Wall-frame - Reduce gap between Cabinets by tighten M6 Hex bolt Assemble Stud Slide 2 cabinet to 1 Slightly fix cabinet to Tighten Hex bolt to guide cabinet Frame (4points) reduce gap Samsung Electronics LED Display Installation...
- Page 36 2. How to install 2-3 Physical Installation: Hex-Bolt Introduction Bolt-Hex Hex bolt used to connect cabinet & cabinet, reduce gap between 2 cabinets Tool: Wrench 10.0mm Samsung Electronics LED Display Installation...
- Page 37 *Internal white pattern : turn on Power, Push Source button 3 seconds and release, wait for display, push one more times. - GAP must be adjusted when install each cabinet. After install all cabinets it’s Hard to modify Gap. - FLUSH can be modify later after installation Samsung Electronics LED Display Installation...
- Page 38 2. How to install 2-3 Physical Installation: Bracket Align Introduction Use Bracket Align to flatten Cabinet-Cabinet , fix by M4 screws. Samsung Electronics LED Display Installation...
- Page 39 2-3 Physical Installation : Bracket Align Introduction Example: 2*2 cabinets 4 points alignment 2 points alignment Bracket Align used to flatten /align position between 2 cabinets. - Use M4 screws to fix Bracket Align with Cabinet Tool: Screw driver, M4L8 screw Samsung Electronics LED Display Installation...
- Page 40 - Reduce gap between Cabinets by tighten M6 Hex bolt - Gap/ flush adjustment like previous steps. Assemble stud guide Slightly fix new cabinet Check top-bottom LED module alignment If can not adjust alignment => Remove Stud Guide Samsung Electronics LED Display Installation...
- Page 41 - Tight M6 bolt to reduce the gap until it has no black seam between cabinets. Rules: New cabinet - New cabinet and around Cabinets are correctly alignment - No black line in full white Check black seam condition at these lines - LED modules are removable with Module JIG Samsung Electronics LED Display Installation...
- Page 42 2. How to install 2-3 Physical Installation: Adjust GAP between cabinets Case 1 : uniform GAP between 2 Cabinets Uniform gap Solution: tighten M6 HEX bolt more to reduce the gap between cabinets Hex bolt Samsung Electronics LED Display Installation...
- Page 43 Small uniform gap Big partial gap Solution : slightly move module A and B together to reduce the gap By hand between them. Try to change from 1 big gap to 3 uniform small gap. Samsung Electronics LED Display Installation...
- Page 44 Flush Guide spec 1) module Flush : 0.07mm↓ LED module 2 LED module 1 2) module gap : 0.05mm ↓ LED module 2 CABINET LED module 1 Flush Samsung Electronics LED Display Installation...
- Page 45 Use Flat screw driver to counterclockwise turn Magnet Bolt * Turn Magnet Bolt counterclockwise 1 circle it will go up 1.0mm Put back LED Module to check the flush, fix LED module position with JIG Flush position Holder magnet Samsung Electronics LED Display Installation...
-
Page 46: Physical Installation
2-3 Physical Installation: Module JIG User Guide (replace Module) Unlock face up for remove Module Put JIG on LED Module Remove JIG together with Module Turn Jig to Lock mode Remove JIG after lock Module Put the module back with Unlock JIG Samsung Electronics LED Display Installation... - Page 47 Cabinet and HDBT IN of the second LED Cabinet. Then repeat. 3) Connect the power using power cords and power extension cables. ※ For details on the cabling method, please refer to 2-4 Data Cabling. Samsung Electronics LED Display Installation...
- Page 48 2. The signal quality is different according to the rolled condition of cable. In case of the random rolled condition, we recommend 50m with CAT5e type. 3. Use an unfolded cable for HDBT signal quality. Samsung Electronics LED Display Installation...
- Page 49 3) Connect from HDBT Out Port of LSB and HDBT IN Source of Cabinet using LAN Cable. 4) Check whether the input source of the first cabinet is HDBT or not. (Check source transition button of the Cabinet) Samsung Electronics LED Display Installation...
- Page 50 While the Screen is being operated, check whether there is any defect on the LED and whether there is any abnormality on the screen. Check whether the connection of DP cables is normal when some monitors are off Sometimes. Samsung Electronics LED Display Installation...
- Page 51 2-3 Physical Installation: T-CON PCB replacement If you must change or repair T-CON and SMPS, open the door using hand + driver turning Captive screw to the left (counterclockwise) that is attached to door. T-CON SMPS Captive screw Samsung Electronics LED Display Installation...
- Page 52 2. How to install 2-3 Physical Installation: T-CON PCB replacement 1. Separate Data Cable and Power Cable of T-CON. 2. Remove 8 Points of Screw that are holding T-CON. Data cable T-CON power board cable Samsung Electronics LED Display Installation...
- Page 53 2. Disassemble the data cable and power cable that are connected to each other. Put on Lock Jig on Module Remove Module, disassemble cable Remove Module with Unlock JIG Data cable Power cable Samsung Electronics LED Display Installation LED module with JIG...
- Page 54 2. When flipping the jig, support with finger so that LED module may not fall out. Remove Lock JIG Flip JIG from Unlock to Lock Assemble the cables Put LED with Unlock JIG Data cable Power cable LED module with JIG Unlock Lock Samsung Electronics LED Display Installation...
-
Page 55: Data Cabling
When connecting DP OUT source of the cabinet with other displays, the screen may not appear normally. DP source is a source that is supported for redundancy if there is a cabinet where abnormality has occurred while being connected to HDBT. Samsung Electronics LED Display Installation... - Page 56 2. How to install 2-4 Data cabling RS232C Redundancy Connection First Cabinet Last Cabinet Only the cabinets connected with the same web can be controlled. Samsung Electronics LED Display Installation...
-
Page 57: Power Cabling
IL(S)025 should be below 4 units. For 220V, All sets should be below 4 units If connected more than recommended, circuit breaker of the product may get tripped due to overload of electricity. First Cabinet Last Cabinet Samsung Electronics LED Display Installation... -
Page 58: Example Of Installation
3. Example of Installation Floor type Ceiling type Wall mounting type Samsung Electronics LED Display Installation... - Page 59 - Example of support structure (2 rows x 6 columns matrix) ∙ The support structure in the below example is typical example for 2R x 6C display. Several variants of support structures are possible for the same size. Contact Samsung for more information.
- Page 60 3. Example of Installation 3-1 Floor type : Example of (5 columns x 6 rows matrix) Component for Assembly : Die-casting gusset + bolt + nut Assy Frame L & R connecting bracket Wheel Samsung Electronics LED Display Installation...
- Page 61 3. Example of Installation 3-1 Floor type : Example of 3columns x 10rows matrix, Curve R6000 Aluminum profile 40*40 Wheel (16EA) component: Die-casting gusset + bolt + nut Al Profile Aluminum T10.0 pipe 20*30 Plastic Cover Samsung Electronics LED Display Installation...
- Page 62 3-2 Wall-mount type Wall Mount & Pocket Structure Wall Mount with Swivel Structure Applied 10cm Make a hole on the Hydraulic Cylinder Open Wall Structure wall and carry out Hydraulic Cylinder work in the rear area Samsung Electronics LED Display Installation...
- Page 63 SECC T3.0 bending, Hole CNC, Black painted Bracket Frame R SECC T3.0 bending, Hole CNC, Black painted Bracket Support Bottom Al T10 , hole CNC, Black Anodizing Bracket Frame Center SECC T3.0 bending, Hole CNC, Black painted Samsung Electronics LED Display Installation...
- Page 64 3. Example of Installation Tolerence : ±1.0mm Tolerence : ±2.0mm Samsung Electronics LED Display Installation...
- Page 65 3. Example of Installation Bracket Frame center dimension Guide <Front View> <Bottom View> *Bracket 홀 관련 치수 Samsung Electronics LED Display Installation...
- Page 66 3. Example of Installation Bracket Frame L/R dimension *hole dimension is same with Bracket Frame Center Bracket Support Top/Bottom dimension Samsung Electronics LED Display Installation...
- Page 67 3. Example of Installation 3-4 Frame Assembly 1. Bracket-Frame is matched by special guide jig. (dimension between hole: horizontal 420mm, vertical 468mm) example 1) [guide jig] example 2) Φ6.0 [guide jig] Samsung Electronics LED Display Installation...
- Page 68 2. Checking the status of bending of frame , degree between Frame and Base structure as 90 degree. 3. There should be 80x370mm hole on the frame for having space to join each cabinet. <Front View> Samsung Electronics LED Display Installation...
- Page 69 3. Example of Installation 4. Frames can be moved horizontal by a rail structure. Rail Ellipse hole Samsung Electronics LED Display Installation...
- Page 70 3. Example of Installation 5. It needs enough space at rear of cabinet for opening the door. Dead space for Bracket-Frame (width 300mm) Samsung Electronics LED Display Installation...
- Page 71 6. It needs a Bracket Cover at border of the display to prevent making a seam by a sagging or a moving of LED module. ◎ Cover Spec (material : Steel , thickness 1.0, tolerence ±0.2) – non provide ◇ Horizontal Cover ◇ Vertical Cover Samsung Electronics LED Display Installation...
-
Page 72: Feature
LSB is connected to the first LED cabinets via HDBT. LED cabinets is connected in daisy chain method via HDBT IN Control PC HDBT and HDBT OUT ports. HDBT Cabinet 2 Cabinet HDBT HDBT Cabinet 3 Cabinet 4 Samsung Electronics LED Display Installation... - Page 73 “Start” button. If the user does not want to set any password, check “Don’t password” option in the checkbox. In this case, when LSM application gets launched, it will no longer require password to log in. Samsung Electronics LED Display Installation...
- Page 74 In Connection list, users can edit connection name, ID Range, AutoSet ID options and Delete the relevant connection information from the Connection List. Press “Connect” button to connect all or select connection in Connection List Samsung Electronics LED Display Installation...
- Page 75 In Connection list, users can edit connection name, ID Range, AutoSet ID options and Delete the relevant connection information from the Connection List. Press “ Connect ” button to connect all or select connection in Connection List Samsung Electronics LED Display Installation...
- Page 76 4. Feature 4-1 PC Control Program LSM(LED Signage Manager) Main Window-Home Window • Home Screen : Displays information of connected devices, Input source, Layout and Faulty devices. Samsung Electronics LED Display Installation...
- Page 77 Cabinet Layout : Displays layout of all LED cabinets, number of cabinets, number of connected cabinets and number of disconnected cabinets. Faulty device: Displays the ID of the LED cabinet in Error and the contents of error. Samsung Electronics LED Display Installation...
- Page 78 Vertical size, Videowall Matrix, X position and Y position settings. (iii)LED Signage Cabinet: X and Y position of cabinet. Show ID: When checked X Position and Y Position of LED Cabinet Save and Cancel setting. Samsung Electronics LED Display Installation...
- Page 79 Check location of each LED cabinet and layout Category View: Home/Connections Tab and Environment Settings Device Information/Setting View: Change LSB Setting (Screen Setting, etc.) Sub Information View: Displays: Monitoring log, LSB Information and LED Cabinet information. Samsung Electronics LED Display Installation...
- Page 80 Change Power On/off, Input Source Setting. 2. Picture: Screen Mode, Brightness, Contrast, Sharpness, Tint, Color Temperature, Gamma and PIP Setting, etc. 3. Picture Option: Color Tone, MPEG Noise Filter, HDMI Black Level, Film Mode, etc. Samsung Electronics LED Display Installation...
- Page 81 4. System: Auto Power On, Auto Power off, Standby Control, Network Standby, Energy Saving, Clock Set, DST, Timer and Reset Setting. 5. Advance Option: Dynamic Contrast, Black Tone, Flesh Tone, RGB Mode Only, ABL Setting, etc. Samsung Electronics LED Display Installation...
- Page 82 ※ In case of using the gamut function, The using necessity over LSM version and Novatek SW version # LSM Version : A-LEDMGDSP- 1003.4 ↑ # Cabinet Novatek SW Version : Basic model : L-ILEMWWAC-1005.0 ↑/ L-ILFMWWAC-1003.0 ↑ / L-ILFMWWBC-1001.0 ↑ Step up model: L-ISFMWWAC-1002.4↑ Samsung Electronics LED Display Installation...
- Page 83 LED Signage Cabinet: LED cabinet’s IC and Power information LED Signage Box: IP address, MAC address, ID Range of LED Cabinet, Number of LED Cabinets (All / Connected / Not Connected), Serial Number, Version Information Samsung Electronics LED Display Installation...
- Page 84 Alter(in degree Celsius) settings. Support: Contains Language, Log Backup export, Faulty device Alert with Time (in mins) and Mail setting, User password settings. Version: Displays current version of the application, Automatic update and Check for update settings button. Samsung Electronics LED Display Installation...
- Page 85 Rr, Gg, Bb = 15,000, Others = 0 ※ The value for 3x3 matrix and brightness and chromaticity can be adjusted for each module unit ※ The Maximum of Each Value can be applied up to 16383 Samsung Electronics LED Display Installation...
-
Page 86: Led Color Correction
- Screen layout - Color correction target - Measuring pattern mode (spacing) ex) FHD : 5x5 spacing - Camera focus optimized - ND filter & exposure time setting - Pixel mapping pre test (about R/G/B color) Samsung Electronics LED Display Installation... - Page 87 - Re-arrange the color difference module position (move to the screen edge area) #7. Final measure & make the correction coefficient (C.C) #8. Apply the C.C file to Cabinet Flash memory use SPI Jig #9. Fine tunning use manual calibration (Module level C.C & edge seam correction) Samsung Electronics LED Display Installation...
- Page 88 DP Out HDBT Out HDBT Out DVI Cable DP Cable S-BOX (1) S-BOX (2) HDBT Cable DVI In DVI In Terminate Graphic : Matrox Mura 2 x FHD Screen Control Box (PC or controller) Wall Controller Samsung Electronics LED Display Installation...
- Page 89 4. Feature 4-2 LED Color correction #2. Setting the cabinet information use LSM S/W Cabinet position S-Box Picture mode “Office-Text” HDMI Black Level “Low” Backlight level 10 Pixel CC off Samsung Electronics LED Display Installation...
- Page 90 #3. PC display setting Multi display (extend Monitor) Use ATI Fire-Pro & NVIDIA Quadro series Can make UHD screen setting UHD screen = 4 x FHD screen (4 x S-Box) Output signal setting (0~255 gray Level). Samsung Electronics LED Display Installation...
- Page 91 #4. Color correction H/W setting Camera position : Center position in front of LED screen Control PC connection PC & Calibration S/W CAMERA (Radiant I-16) (R社 Vision Cal 10.X,X) USB or Ethernet Video output ↔ S-Box S-BOX Samsung Electronics LED Display Installation...
- Page 92 4. Feature 4-2 LED Color correction (Vision 4.8.29 ver.) #5. Vision Cal S/W setting (Radiant Program) : screen layout - Screen Layout - Detector Shape ‘Rectangle’ - Detector Width : Pitch size x spacing Samsung Electronics LED Display Installation...
- Page 93 4. Feature 4-2 LED Color correction (10.x.x ver.) #5. Vision Cal S/W setting (Radiant Program) : Color correction target (좌표 값 설정) Enter Target value about R/G/B/W Samsung Electronics LED Display Installation...
- Page 94 4. Feature 4-2 LED Color correction (10.x.x ver.) #5. Vision Cal S/W setting (Radiant Program) : Measuring pattern mode (spacing) ex) FHD : 5x5 spacing Samsung Electronics LED Display Installation...
- Page 95 4. Feature 4-2 LED Color correction (10.x.x ver.) #5. Vision Cal S/W setting (Radiant Program) : Camera focus optimized Recommend focus level : one LED pixel > 10x10 CCD pixel Samsung Electronics LED Display Installation...
- Page 96 4. Feature 4-2 LED Color correction (10.x.x ver.) #5. Vision Cal S/W setting (Radiant Program) : ND filter & exposure time setting determined by LED brightness & spacing figure Samsung Electronics LED Display Installation...
- Page 97 4. Feature 4-2 LED Color correction (10.x.x ver.) #5. Vision Cal S/W setting (Radiant Program):Pixel mapping pre test (about R/G/B color) Samsung Electronics LED Display Installation...
- Page 98 4. Feature 4-2 LED Color correction #6. 1st Measurement & check correction result Re-arrange the color difference module position (move to the screen edge area) Samsung Electronics LED Display Installation...
- Page 99 4. Feature 4-2 LED Color correction #7. Final measure & make the correction coefficient (C.C) Final Measurement - Select “Run All” * measurement time : 40min @ FHD resolution Samsung Electronics LED Display Installation...
- Page 100 4-2 LED Color correction #8. Apply the C.C file to Cabinet Flash memory use SPI Jig Use SPI jig & SPI writer s/w, can save C.C data to Module flash memory : select “Product model” → select “START” Samsung Electronics LED Display Installation...
- Page 101 Reset * All reset buttons is dimmed before data is edited • Apply edited data / maintain screen Apply * Apply is dimmed before data is edited • Go to device screen without saving Cancel Samsung Electronics LED Display Installation...
- Page 102 4-2 LED Color correction #10. S-BOX Menu “ S-BOX Player connect - Select “ 사진 변경 [1931 CIEXYZ 색도표] LED Display “Color Temperature” select (Default : 6500K) 6500K ↑ : Cool color 6500K ↓ : Warm color Samsung Electronics LED Display Installation...
- Page 103 [1931 CIEXYZ 색도표] (Default: 128) 1. R-Gain 128↑: Redish , 128↓: Cyanish 2. G-Gain 128↑: Greenish, 128↓: Magentaish 3. B-Gain 128↑: Blueish, 128↓: Yellowish ※caution : When adjusting, recommend the control from R / B Gain. Samsung Electronics LED Display Installation...