Samsung shs-2920 Instruction Manual

Instruction
Manual
Convenient Opening of the
Door
Simple operation via card and
passcode
Automatic card recognition
feature
Convenient card recognition when
contacting the card
Dual-Authentication
Feature
Dual-Authentication feature through
card and passcode
Dual-Lock Feature
With dual-lock feature, the security
is enhanced
Fire Detection Feature
Built-in fire detection sensor
Crime prevention feature
when going outside
Alarm feature for inside activation
when going outside
Internet Home Page
SamsungSNS(Inc.)
Anywhere in the country If you accurately provide the product name,
ServiceCenter
fault condition, and contact number, then
Representative we will always provide kind assistance and
quick service to customers' questions.
PhoneNumber
Opening the door from the outside
(passcode)
When the product is first purchased, it is set in dual-security
mode. To set the product into normal mode, please refer to
the 'dual-security mode setting" method.
1. Tuch the [Number keypad]
[Number Keypad] is touched.
2. Enter the passcode.
Dual-security mode
Two buttons randomly lit up, When all of the lights in the
so press the two numbers in number keypad show up, enter
the sequence. the passcode and press [*]
button.
When all of the lights in the number keypad show
up, enter the passcode and press [*] button.
Passcode must be entered when the number keypad is lighted up,
so if the lights are not on, then touch the [number keypad] and then
re-enter the passcode.
Reference
When the passcode is incorrectly entered to cancel the input, press
the [ ]button and start from the beginning.
If the passcode is incorrectly entered for five consecutive sounds, a
different alarm sound is played for about 10 seconds, and the
operation of doorlock is paused for roughly 3 minutes. During the
operation pause status, "beep" sound is played every 10 seconds,
and after 3 minutes, a long "beep" sound is played, and the pause
status is automatically disabled.
Precautions for Safety
Precautions for safety protect the user's safety and prevent damages
and inconvenience due to accidents. Please read this and use the
product properly.
Warning
Do not install or repair the product
randomly as you want.
Do not install the product in a location
where the gap between the door and
doorframe is more than 5mm.
Cautiously manage the passcode so
that other people cannot know it, and
regularly change the number.
Do not operate the product when your
hand is wet, and be careful to not let
water, beverages, and other liquid to
get inside the product.
Do not forcibly press or use a sharp
tool to hit the button.
When you are going out, always check
the ensure that the door was fully
locked.
Product Components
Product components may be changed depending on the
installation environment.
Outside of Main Unit
Warning
You must carry or keep at least one
emergency key outside.
In the case of an emergency, please
read and learn the instruction for
manual switchgear.
Opening the door from the outside
(card, key tag)
When the product is first purchased, it is set in automatic
detection mode. To set it to manual detection mode, please
refer to "card automatic/manual detection setting" method.
Automatic
Detection
Mode
Manual
Detection
Mode
Touch the [number pad]
Success :
↑'Beelililic' melody
Fail : Short beep~
Reference
Opening and closing the door from
the inside
Electrically opening the door Electrically closing the door
Success : ↑'Beelililic' melody
With the door locked, pressing
Fail : Short beep~
the [OPEN] button of the main unit
on the inside opens the door.
Mechanically opening the
door
With the door locked, turn the
manual switchgear to
Properly fit the battery into the product
onto its accurate (+/-) terminals. When
the battery is incorrectly placed in its
direction or charge as displayed into
the battery room, leakage and breakage
may occur, so please be careful.
When the battery life is ended, replace
all the batteries at once, and avoid
using new and used batteries at the
same time.
When cleaning the product, do not
wipe it with water, benzene, or alcohol,
and instead, use a dry cloth.
Replace the batteries to new ones
within one week of first hearing the
battery replacement notification alarm.
Inside of Main Unit Doorframe Strike Plate
(Strike)
Key-Tag (2EA)
'AA' Battery (LR6) (4EA)
Spacer
Instruction Manual
Installation Screw
Installation
Paper Diagram
Fixed Panel
Contact the card and key tag
to the [card recognition area].
The door will open within one
second.
Success :↑'Beelililic'
Fail : Short beep~
When the number pad is lighted up,
contact the card or key tag in the
[card recognition area].
After 1 seconds, the door is opened.
In the case of a card or a key tag which is not recognized
automatically, the door will be open after touch the number
pad and place it.
↑Beelillic ↓Beellic
With the door manually locked,
pressing the [OPEN] button of the
main unit on the inside locks the
already closed door.
Mechanically closing the
door
With the door closed in manual
direction. lock status, turn the manual
switchgear to direction.
Names and Features (Outside)
Number Keypad
Turned Off Number Keypad On
Number Keypad
Touch
Names and Features (Intside)
Opening the cover of the main unit on the inside
Gently press the battery cover of the main unit on the inside
and pull the cover in the direction shown in the arrow.
※ All registration and setting up can only
be operative while the door is open.
Passcode Registration
Passcode can be registered in 4~12 digits, and only one
can be registered to use.
1. Press the [Register] button. 2. Register the new passcode.
Beep
Open the battery cover and shortly Enter the new passcode (4~12
press [register] button. digits) and press the [*] button.
To prevent theft accidents, it is recommended to use the passcode
that is 6 digits or longer (only 0~9 numbers are usable).
Please be careful to manage the passcode so that other people will
Caution
not know. Using the same passcode for a long period of time may
lead to its exposure, so regularly change the passcode for use.
Registered passcode cannot be deleted, so register a new passcode
to use.
Check with the new passcode to see if the passcode was registered
normally, and then close the door.
Card and Key Tag Registration
When card or key tag is registered, previously registered card
and key tag information are all deleted, so try to register all
cards and key tags at once. Total of 20 card keys and key tags
can be registered (ISO 14443 Type A support)
1. Press the [Register] button. 2. Contact card and key tag.
Beep
Open the battery cover and shortly Contact the card or key tag that
press [register] button. needs to be registered.
3. End card key registration
To end registration, press the
↑Beelililic
[register] button of the main unit on
the inside.
To register various cards and key tags continuously, register the card or
key tag, and contact another card or key tag within 10 seconds. If another
card or key tag is not registered within 10 seconds, the registration
automatically ends.
Caution
To check if the card or key tag is normally registered, check the card and
key tag, and then close the door.
"Samsung SNS Doorlock" abides to the "ISO 14443 Type A standards, and
the cards, key tags, and NFC-use smartphones that completed
certification from "Samsung SNS Doorlock" are able to be registered on the
doorlock for use.
Number Keypad
Battery replacement
notification
Card Recognition Area
Reset hole
External Power
Contact Area
Registration Button
OPEN Button
Manual Switchgear
Deadbolt
Deadbolt
Door Opening Sensor
Automatic/Manual
Lock Conversion
Switch
Beelililic
Beelililic