Samsung SHP-H20 User Manual

SHP-H20
Convenient Door Opening
Easy access with PIN code and Key tag
Silent Mode
When going in or out, the sound of the
key entering and door opening will be
suspended.
Automatic Key Tag Reading Function
When a user places a key tag on the reader,
it automatically recognizes the key tag.
2-Step Authentication Mode
Both PIN code and key tag need to be authenticated
to open the door, ensuring a higher level of security.
Privacy Mode
Unlocking the door from outside is prevented while
someone is inside.
Away Mode
After a user goes out, this function generates
alarm sound when an attempt is made to open
the door from the inside.
High Temperature Alarm
When the built-in sensor detects abnormal
high-temperature, the alarm will be triggered,
and the doorlock will be automatically unlocked
to allow fast escape.
smarthome.samsungsds.com
Opening the Door from Outside (PIN code)
When purchased, the product is set to Multi-leveled Security Code Entry Mode
initially. Please, refer to 'Multi-leveled Security Code Entry Mode setting' for
Common Mode setting.
※ Silent Mode
Before entering the PIN code, press the [] button and enter the PIN code, then both
the sound of the key entering and the door opening will be muted.
It is a useful function if you do not want to disturb neighbors when you go in and
out at night.
1. Randomizer Mode
Touching [Number When two arbitrary
Pad] will light up buttons are lighted,
the number pad. press the buttons
in order.
2. Common Mode
Touching [ Number Pad ]
When the number pad lights up, enter the
will light up the number pad.
PIN code and press the [] button.
●
PIN code must be entered after the light is on, and if does not, touch [Number Pad]
and re-enter.
●
Note To cancel, press [ ] button and re-enter.
●
If the PIN code is wrong 5 times, "peep" warning alarm will sound 20 times and
the system will shut-down for about 3 minutes. When malfunction happens,
"beep" will sound every 10 seconds, and stop mode will be turned
off automatically after 3 minutes with multiple 'beeps'.
Opening the Door from Outside (Key Tag)
A locked door can be opened from outside by using a key tag.
Place the registered key tag on the key tag sensor.
Success:
Place the key tag on the key tag sensor.
Be be be beep↑
Fail: The door will be opened after 1 second.
Ding dong ding dong
●
When the key tag sensor does not recognize the key tag, touch
the number pad and put the key tag on the key tag sensor to
Note open the door.
Safety Precautions
This section contains important information to ensure the user's safety
and prevent potential damage to property.
Please, read this section carefully and use the product accordingly.
Warning
• The installation and repair should be done
by the professional installer or service
person.
• Do not install the product in the place
where the gap between the door and the
frame is 5 mm or more.
• Long-term exposure to direct sunlight
may cause a crack on its touch pad.
Avoid exposure to direct sunlight.
• Do not use the excessive force or sharp
objects to push the lock buttons, as this
can damage the product.
• Do not operate the product with wet
hands, and keep liquids such as water
or drinks away from the product, or the
product may malfunction or be damaged.
• Do not use water, benzene or alcohol
when cleaning the product, but use a soft
dry cloth.
• Make sure that the door is completely
closed when going outside.
• Make sure that no unauthorized person
has the access to the PIN code .
※ The information of this user manual is subject to change without any
notices to improve the performance of this product.
※ Customer's improper installation may result in a additional service costs.
We highly recommend professional installation.
Product Components
The product components may vary depending on the installation
environment.
Exterior Unit
RF Key Tag : 2EA
●
User Manual
●
'AA' Batteries (LR6)
●
PTMP5800ONTB ED:00
Opening the Door from the Inside
Success: Locking the Door from Outside
BE BE BE BEEP↑
Fail:
DING DONG DING DONG
Automatic Locking Setting
When the numbers on the
number pad are lighted, enter
Manual Locking Setting
the PIN code and press the
[  ] button.
Success:
BE BE BE BEEP↑
Locking the Door from the Inside
Fail:
DING DONG DING DONG
Automatic Locking Setting
Manual Locking Setting
All registration and setting are activated only when the door is opened.
Initialization (PIN code , Key Tag)
All registered data (PIN code , Key tag) are deleted.
After initialization, the PIN code is set to '1234', and the registered key tag
data are erased. Please register a new PIN code after initialization.
1. Press [Register] Button
DING DONG →
DING DING
Open the battery cover of the
inner body and press the [Register]
button for 3 seconds.
4
Change it regularly.
• Be sure to correctly match the battery
polarities (+/-) when installing the batteries.
Wrong direction of battery polarities may
cause the battery liquid leakage or the burst
of them.
• When the battery replacement alarm
melody is generated, use all new batteries
instead of the existing batteries.
• According to the wireless communication
environment, its battery may consume
much.
• Interference in wireless communication
may occur when this product is used, or
radio interference may occur from other
devices.
• As this radio system may have radio
interference during the operation, it cannot
provide a service for human lives.
• Too much dew condensation may affect the
performance of this product.
• Keep 20 cm or longer away from this
product when using it.
Mortise
Interior Unit
Strike Plate Dust Box
Handle Shaft Spring
●
Handle Shaft, Installation Screws
●
Installation Manual
●
In order to open from indoors,
push the Inner Handle downwards to unlock.
The door is automatically locked 2 seconds after the
door is closed.
Touch the out body unit number pad
to lock the door.
The door is automatically locked 2 seconds after the
door is closed.
The door is locked when the
[ CLOSE / DOUBLE LOCK ] button
from the inside is pressed.
2. Enter the Numbers for Initialization
Success:
DING DONG DENG
Fail:
DING DONG DING DONG
When the number pad is lighted, enter
'4560852580' and then press the
[] button.
Exterior Unit Parts
Entry Complete/
Silent Mode Touch Button
Battery Replacement Alert
LED
External Power
Exterior Unit Handle
Interior Unit Parts
Battery Cover
Door open /
Warning LED
Interior Unit Handle
Mortise
2
Change the PIN code
A user can register a PIN code (4 to 12 digits), and only one PIN code canbe
registered, The default PIN code is "1234."
1. Press [Register] Button 2. Enter a New PIN code
DING DONG
Open the battery cover of the inner body Enter the new PIN code (4 to 12 digits)
and press the [] button.
and press the [Register] button shortly.
● To prevent an intrusion, it is recommended to make a PIN code with 6 or
more digits. (Each digit number ranges from 0 to 9.)
● Manage your master PIN code with care so that unauthorized people will not
Warning have access to it. Regularly changing your PIN code can reduce the risk of it
being leaked.
● A registered PIN code cannot be deleted. Register a new PIN code .
● To make sure the PIN code has been properly registered, check the new
PIN code and close the door.
● If checking the new PIN code fails, initialize the key information (see page 5)
to initialize the PIN code, and change the PIN code again.
Key Tag Registration
During registration, already registered key tags will be deleted.
Please register all key tags at once.
Up to 20 key tags can be registered. (Only ISO14443 A Type is available.)
1. Press [Register] Button
DING DONG
Open the battery cover of the inner body
and press the [ Register] button shortly.
3. Exit Registration Mode
If you want to end this process,
press the [Register] button
DING DONG DENG of the inner body shortly.
●
To register multiple key tags, lightly place another key tag to
the Key tag reader within 20 seconds after registering the previous key tag.
●
Only the key tags provided by Samsung SDS can be used.
Warning
●
Samsung SDS will not take responsibilities for any problem that may
occur because you used an authentication means other than the
key tags that we provided.
5
Number Pad
Away Mode Touch Button
Key Tag Reader
Reset Button
1.5V AA Batteries
[ Registration ]
Button
[ CLOSE / DOUBLE LOCK ]
Button
Dead Bolt
Latch Bolt
3
DING DONG DENG
2. Place the Key Tag Reader
DING DONG DENG
Place the key tag to be registered
on the key tag reader of the outer body.
You will know the key tag has been
registered when "DING DONG DENG"
sounds.
6