Panasonic WJ-RT208 Operating Instructions Manual page 36

3.1.2 Record search (SEARCH)
Refer to 3. 2.
3.1.3 Recording & event setup (REC & EVENT)
Timer recording (TIMER REC)
(1) Press the [MENU] button. "WJ-RT208 SETUP MENU"
appears.
WJ-RT208 SETUP MENU
SYSTEM MANAGEMENT
SEARCH
REC&EVENT SETUP
PTZ SETUP
CAMERA SETUP
COMMUNICATION SETUP
REPORT
USER INFORMATION
DATA MANAGEMENT
(2) Move the cursor to "REC&EVENT SETUP" and press the
[SET] button.
TIMER REC
TERMINAL REC
VMD REC
RECORD LENGTH
AUDIO SELECT
(3) Move the cursor to "TIMER REC" and press the [SET]
button. The "TIMER REC" menu is displayed.
Channel 1
SUN 00: 00 24: 00
MON 00: 00 24: 00
TUE 00: 00 24: 00
WED 00: 00 24: 00
THU 00: 00 24: 00
FRI 00: 00 24: 00
SAT 00: 00 24: 00
DAILY 00: 00 24: 00
All
Camera identification: 1 - 8
Picture quality: "SP Fine/Fine/Good/Normal/Extended"
Default: "Normal"
Frame rate: "Full, 1/2F, 1/4F, 1/8F, 1/16F"
Default: "Full"
36
REC & EVENT
TIMER REC
Normal Full CBR
Off 00: 00 24: 00
Off 00: 00 24: 00
Off 00: 00 24: 00
Off 00: 00 24: 00
Off 00: 00 24: 00
Off 00: 00 24: 00
Off 00: 00 24: 00
Off 00: 00 24: 00
OK Cancel
Stream type: "CBR" or "VBR"
Default: "CBR" (If screen changes seem extreme,
Recording date: "SUN", "MON", "TUE", "WED", "THU",
"FRI", "SAT", "DAILY"
Two types of "Period1" and/or "Period2" can be set
up for one day.
If the same setting is used every day, the setting
should be made with "DAILY". When all time spans
have been set up, select "On".
Default: 00:00 - 24:00, "Off"
(4) If the same setting is required for all channels, press
[All] after completing the setting for one channel. All the
parameters are then made identical to that setting.
Press the [SET] button to close the prompt box.
(5) Move the cursor to [OK] and press the [SET] button.
Note: When trying to stop the recording by changing
the settings in the process of the timer recording,
recording will not stop immediately. The timer
recording will not stop until it reaches the end time
of the set duration for the timer recording. (When
two durations are set, the timer recording will stop
when it reaches the end time set later.) To stop the
timer recording, stop recording manually after
changing the settings for the timer recording.
Terminal recording (TERMINAL REC)
(1) Press the [MENU] button. "WJ-RT208 SETUP MENU"
appears. Move the cursor to "REC&EVENT SETUP" and
press the [SET] button. (Refer to steps (1) and (2) in
3.1.3.)
Off
Off
Off
TIMER REC
TERMINAL REC
Off
VMD REC
Off
RECORD LENGTH
Off
AUDIO SELECT
Off
Off
(2) Move the cursor to "TERMINAL REC" and press the
[SET] button.
the setting made at "VBR" is preferable.)
Current channel information
has been copied to all
channels!
OK
REC & EVENT