Makita RP1800 Instruction Manual
Hide thumbs
Also See for RP1800:
- Instruction manual (100 pages) ,
- Instruction manual (73 pages) ,
- Instruction manual (82 pages)
Related Manuals for Makita RP1800
Summary of Contents for Makita RP1800
- Page 1 INSTRUCTION MANUAL Router RP1800 RP1800F RP1801 RP1801F RP2300FC RP2301FC 009852 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
-
Page 2: Specifications
0.38 Ohms it can be presumed that there will be no negative effects. The mains socket used for this device must be protected with For Model RP1800 a fuse or protective circuit breaker having slow tripping ENF100-1 For public low-voltage distribution systems of characteristics. - Page 3 EC Declaration of Conformity The typical A-weighted noise level determined according Makita Corporation responsible to EN60745: manufacturer declare that the following Makita Sound pressure level (L ) : 86 dB(A) machine(s): Sound power level (L ) : 97 dB(A) Designation of Machine:...
- Page 4 Keep children and bystanders away while 15. Do not overreach. Keep proper footing and operating a power tool. Distractions can cause balance at all times. This enables better control you to lose control. of the power tool in unexpected situations. Electrical safety 16.
-
Page 5: Router Safety Warnings
SAVE THESE INSTRUCTIONS. 27. Keep handles dry, clean and free from oil and grease. GEB018-2 WARNING: ROUTER SAFETY WARNINGS DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence Hold power tools by insulated gripping to safety rules for the subject product. - Page 6 Nylon nut Switch action 1. Nylon nut 1. Lock button 2. Switch trigger 009855 009864 The upper limit of the tool body can be adjusted by CAUTION: turning the nylon nut. Before plugging in the tool, always check to see •...
-
Page 7: Installing Or Removing The Bit
Speed adjusting dial CAUTION: For model RP2300FC,RP2301FC only Do not look in the light or see the source of light • directly. 1. Speed adjusting Pull the switch trigger to turn on the light. The lamp dial keeps on lighting while the switch trigger is being pulled. The lamp turns off 10 - 15 seconds after releasing the trigger. -
Page 8: Operation
OPERATION dimensions. When using the straight guide or the trimmer guide, • be sure to install it on the right side in the feed CAUTION: direction. This will help to keep it flush with the side Before operation, always make sure that the tool •... - Page 9 Fine Adjusting Function for Positioning Blade 1. More than 15 in Relation to Straight Guide 2. Straight guide 1. Adjusting screw 3. Wood 55 mm 55 mm 004931 When using a large diameter bit, attach pieces of wood 009873 to the straight guide which have a thickness of more than 15 mm to prevent the bit from striking the straight Loosen thumb nut (M6 x 50mm).
- Page 10 guide. The distance (X) can be calculated by using 1. When set to the following equation: maximum Distance (X) = (outside diameter of the templet opening width guide - bit diameter) / 2 Trimmer guide (optional accessory) 009870 Templet guide (optional accessory) 009867 Trimming, curved cuts in veneers for furniture and the like can be done easily with the trimmer guide.
-
Page 11: Depth Of Cut
Dust nozzle set (Accessory) 1. Installing the screw and washer on the tool Attach flat washer onto this screw. • Insert this screw through a screw hole in the tool • base and then screw in the threaded part in the motor bracket of the tool. -
Page 12: Maintenance
(1.0 mm per a full turn) brake operation when releasing the switch trigger. If Turning it clockwise makes the depth of cut greater electric brake is not working well, ask your local Makita • and turning it counterclockwise smaller. -
Page 13: Router Bits
Router bits "V"Grooving bit Straight bit 005118 005116 1/4" 006454 1/4" Drill point flush trimming bit 1/2" 1/2" 1/4" 1/4" 006452 005120 "U"Grooving bit 006456 Drill point double flush trimming bit 005117 006453 005121 006457... - Page 14 Board-jointing bit Cove beading bit 005123 005129 006459 006464 Corner rounding bit Ball bearing flush trimming bit 005125 005130 006460 1/4" 006465 Chamfering bit Ball bearing corner rounding bit 005126 005131 1/4" 006462 006466...
- Page 15 Ball bearing chamfering bit Ball bearing roman ogee bit 005132 005135 1/4" 006470 006467 Ball bearing beading bit 005133 006468 Ball bearing cove beading bit 005134 006469...
- Page 16 Makita Corporation Anjo, Aichi, Japan 884877C225...