Rear Panel Facilities - Pioneer PRV-LX10 Service Manual

1

• Rear Panel Facilities

1
A
B
No. Name
1 AC IN connector
2 Main power switch
3 AUDIO CH1/L CH2/R IN/OUT
connectors
4 S-VIDEO IN/OUT connectors
C
5 COMPOSITE VIDEO IN/OUT
connectors
6 COMPONENT VIDEO IN/OUT
connectors
7 DV connector (*6)
8 Fan motor
9 LTC connector (*2)
10 EXT SYNC IN and through
Output connector
11 Terminate switch
D
12 SIGNAL GND terminal
13 REMOTE IN/OUT connectors
14 PCM/ DIGITAL OUT connector
15 ETHERNET connector
16 MOUSE/KEYBOARD connectors
17 VGA (GUI) connector
18 UPS connector
E
19 Expansion slot 1
20 Expansion slot 2
*1 Inputs are compatible with signal levels for both BETA and SMPTE (NTSC only). However, since outputs are based on DVD format, they
differ from BETA and SMPTE levels. As a result, outputs should be used only for monitoring.
*2 LTC is not supported in drop frame mode.
*3 SONY is a trademark of Sony Corporation. Frame precision is not guaranteed when this unit is used as a playback unit for editing.
This component does not support control from an editing machine.
*4 Functionality of connected devices is not guaranteed. If a USB hard disk drive is not recognized, or if operation is unstable, change to a hub
supporting USB 2.0. If USB mouse and keyboard operation is unstable, try disconnecting and reconnecting the USB connector.
If operation continues to be erratic, inquire your Pioneer dealer or one of the service centers listed at the end of this manual.
F
*5 The VGA output connector is provided for future expansion use; at present, the connector does not support the output of GUI display signals
Whenever connecting a DV cable to the rear panel DV connector, be sure to attach the accessory ferrite core to the cable.
192
1
2
19
2 3
18
Connect to power cord.
When set to ON, the unit enters standby condition and front panel indicator
lights orange.
Input/output connectors for analog audio CH1/L CH2/R signals.
Input/output connectors for S-VIDEO video signal. Output is compatible with S2.
Input/output connectors for analog composite video signals.
Note: Use coaxial cables (impedance: 75-ohm) to connect with BNC plugs.
Input/output connectors for analog component video signals. (*1)
Note: Use coaxial cables (impedance: 75-ohm) to connect with BNC plugs.
Connect to DV connector of professional use VTR or similar component.
Fan motor for cooling internal parts.
Connector for obtaining time code from VHS, VTR, etc.
Note: Use a coaxial cable (impedance: 75-ohm) to connect with BNC plugs.
Use for connecting external sync signal, and for pass-through signals.
Note: Use coaxial cables (impedance: 75-ohm) to connect with BNC plugs.
Use to terminate sync signal. Set to ON when used alone or when connected to a terminating
unit.
Ground terminal for signals. When using the unit in environments exposed to high levels of
electronic noise, malfunctions may occur to mouse and other control devices. In such cases,
connect a ground wire between the components to reduce the noise. This is not an electric
safety ground.
RS-422A compatible external control connector. The protocol is compatible with SONY
format. (*3)
Digital audio output connector.
Note: Use a coaxial cable (impedance: 75-ohm) to connect with RCA in plugs.
Use for network connection.
Allows connection of a USB mouse, USB keyboard and USB HDD to the unit. (*4)
Connect to VGA monitor for expanded operation. (*5)
Connect when using UPS.
Provided to allow installation of the optional SDI AES/EBU input board (PRA-BD11).
• Consult your dealer regarding installation.
Provided to allow installation of the optional SDI AES/EBU output board (PRA-BD12).
• Consult your dealer regarding installation.
PRV-LX10
2
3
20
4 5 6 7
17 16 15
Function
3
4
8 9 10
SIGNAL GND
14 13 12 11
4