Summary of Contents for RIDGID AF3000
- Page 1 $) 2:1(56 0$18$/ $,5%251( ),/75$7,21 6<67(0 ‡ $VVHPEO\ ‡ 2SHUDWLRQ ‡ 5HSDLU 3DUWV )RU <RXU 6DIHW\ 48(67,216 25 &200(176" &$// 5,'*,' 5HDG DOO LQVWUXFWLRQV FDUHIXOO\ Part No. SP6154 Printed in Canada...
-
Page 2: Table Of Contents
Do not use with damaged cord, plug or damage to Airborne Filtration System, use other parts. If your Airborne Filtration Sys- only RIDGID recommended accessories. tem is not working as it should, has miss- Sparks inside the motor can ignite flam- ing parts, has been dropped, damaged, mable vapors or dust. -
Page 3: Save These Instructions
Do not handle plug or the Airborne Filtra- WARNING: To reduce the risk of tion System with wet hands. electric shock - do not expose to rain - store indoors. Keep hair, loose clothing, fingers and all parts of body away from openings and WARNING: For your own safety, read moving parts. -
Page 4: Unpacking And Checking Carton Contents
Unpacking and Checking Carton Contents Remove entire contents of carton. Check List. Contact 1-800-4-RIDGID if any parts each item against the Carton Contents are damaged or missing. Carton Contents List Description ......Qty. Airborne Filtration System ..1 Owners Manual......1... -
Page 5: Installation Procedure
Installation Procedure WARNING: For your own safety, 2. Joists are normally sixteen inches never connect plug to power source apart. Spacing of holes on width of outlet until all assembly steps are unit is 19-7/16", and on length of unit complete and you have read and is 26"... - Page 6 Installation Procedure (continued) 6. The next step is to install the eye bolts in the top of the unit. To do this, you must remove the three filters first. Ceiling Refer to drawing under “Maintenance” Joist section for location of three types of fil- ters.
-
Page 7: Electrical Requirements
14. Reinstall filter cover plates by slipping upper loop of extension spring to bot- tab into slots in end frame, then pivot tom loop of fourth double loop of to side panel. Reinstall fasteners. chain. Repeat for other three springs. Refer to figure shown on previous 15. - Page 8 Electrical Requirements (continued) Improper connection of the equipment grounding conductor can result in a risk of 3-Prong Plug Properly electric shock. The conductor with insula- Grounded tion having an outer surface that is green Outlet with or without yellow stripes is the equip- ment grounding conductor.
-
Page 9: Operation
Operation WARNING: To avoid fire or explo- Your RIDGID Airborne Filtration System is sion, do not operate this filter unit in equipped with an Pull On/Pull Off switch, areas with flammable gases or flam- a light to show power is ON, and a power mable vapors such as lighter fluid, cord to plug into your electrical outlet. -
Page 10: Removal
Maintenance (continued) In addition to cleaning and/or replacing WARNING: For your own safety, use both filters the Exhaust Filter (Part No. only RIDGID replacement filters. 824295) requires periodic inspection and WARNING: To avoid electrical cleaning. Simply wash in warm water with shock, be sure to replace screw that a mild detergent, dry, and then reinstall. -
Page 11: Wiring Diagram
Wiring Diagram White Black Quick Connections Wire Nut Ground Black Black Switch Light Black Wire Nut White Black Blower... -
Page 12: Repair Parts
Repair Parts Airborne Filtration System Model Number AF30000 Always order by Part Number - Not by Key Number Part No. Description Cabinet 825946-4 Cover 825950-2 † Pre Filter - Intake RF3001 † Fine Filter - Mid Bag Type RF3002 Filter - Exhaust 826424 Blower Assembly 824311-1... - Page 13 Repair Parts Airborne Filtration System Model Number AF30000...
- Page 14 Lifetime Warranty On RIDGID Tools The RIDGID REPUTATION is the result of the consistent product quality and years of pride in workmanship. Rigorous checks and controls from raw materials to packaged products insure product confidence widely accepted as the mark of the professional trades. Therefore,...