Advertisement
IMPORTANT:
Read Before Using
GLL3-330C
GLL3-330CG
Call Toll Free
for Consumer
Information &
Service Locations
For English Version
1.800.561.8187
Operating/Safety Instructions
Consignes de fonctionnement/sécurité
Instrucciones de funcionamiento y seguridad
Pour obtenir des informations
et les adresses de nos centres
de service après-vente,
appelez ce numéro gratuit
See page 5
www.
IMPORTANT :
Lire avant usage
Version française
Voir page 19
.com
IMPORTANTE:
Leer antes de usar
0 C
- 3 3
L 3
G L
Llame gratis para
obtener información
para el consumidor y
ubicaciones de servicio
Versión en español
Ver la página 33
information@itm.com
Advertisement
Table of Contents
Related Manuals for Bosch GLL3-330C
Summary of Contents for Bosch GLL3-330C
- Page 1 Lire avant usage Leer antes de usar Operating/Safety Instructions Consignes de fonctionnement/sécurité Instrucciones de funcionamiento y seguridad - 3 3 GLL3-330C GLL3-330CG Call Toll Free Pour obtenir des informations Llame gratis para for Consumer et les adresses de nos centres obtener información...
- Page 2 - 3 3 GLL3-330C GLL3-330CG 1.800.561.8187 information@itm.com www. .com...
- Page 3 1.800.561.8187 information@itm.com www. .com...
- Page 4 (CR 2032) BAT411-BAT415 GBA12V30 1 608 M00 C1B BC330 BC430 1.800.561.8187 information@itm.com www. .com...
- Page 5 LR 6 0 601 069 H10 0 601 069 J11 BM 1 0 601 015 A01 1 608 M00 05B 6 082 762 25N (GLL3-330C) 1 608 M00 05J (GLL3-330CG) BP350 BT 150 0 601 096 B00 0 601 015 B00 1.800.561.8187...
-
Page 6: Safety Symbols
Safety Symbols The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. - Page 7 DO NOT use this laser tool for any purpose DO NOT charge alkaline batteries. other than those outlined in this manual. DO NOT mix old and new alkaline batteries. This could result in serious injury. Replace all of them at the same time with new DO NOT leave the laser tool “ON”...
-
Page 8: Noise Information
Magnets Battery tool use and care Recharge only with the charger specified by Keep the tool, positioning the manufacturer. A charger that is suitable for device BM 1 24, laser receiver one type of battery pack may create a risk of LR 6/LR8 25, and laser target fire when used with another battery pack. -
Page 9: Fcc Caution
Avoid operation in the direct vicin- Inc. and any use of such marks by Robert ity of the human body over longer periods Bosch Tool Corporation is under license. FCC Caution The manufacturer is not respon- that interference will not occur in a particu- sible for radio interference caused lar installation. -
Page 10: Technical Data
19 Serial number 9 Bluetooth ® button *The accessories illustrated or described are not included as standard delivery. Technical Data Laser Line GLL3-330C GLL3-330CG Working range (typical) –without laser receiver (diameter) 200 ft (60m) 200 ft (60m) –with laser receiver (diameter) - Page 11 B o s c h commercially available LR 6 (AA) batteries chargers listed in the or with a Bosch rechargeable lithium-ion technical data section of this manual. Use battery pack. of other chargers may increase the risk of Operation with Bosch Rechargeable fire, personal injury and property damage.
- Page 12 The non-rechargeable battery adapter is intended only for use in designated Charge Condition Bosch laser tools and must not be used Continuous lighting, green 100–75 % with power tools. Continuous lighting, yellow 75–35 % To insert the batteries, slide the cover 11 of the battery adapter into the battery port 10.
-
Page 13: Initial Operation
Operation Initial Operation Automatic Shut-off When no button on the tool is pressed for approx. 120 minutes, the tool automatically certain conditions while operating the switches off to save the batteries. tool. Therefore, keep the tool away from your ear or other persons. The loud audio To switch on the tool after automatic shut-off, signal can cause hearing damage. -
Page 14: Automatic Leveling
Do not turn on laser automatically compensates irregularities r e m o t e l y u s i n g t h e Bosch app within the self-leveling range of ±4°. The without line of sight to the laser tool. The... - Page 15 Should the laser tool exceed the maximum – The calibration interval (every 12 months) deviation during one of the tests, please have has expired. it repaired by a Bosch after-sales service. – The laser tool was stored outside of the storage temperature range. Working Advice –...
- Page 16 – Direct the laser against the close wall A and On the measuring distance of 2 x 16ft = 32ft, allow the tool to level in. Mark the center of the maximum allowable deviation is: the point where the laser lines cross each 32ft x ±0.0024in/ft = ±5/64 (0.078 in) other on the wall (point I).
- Page 17 – Mark the center of the laser line at the plane is generated aside of the tool. Turn the upper edge of the door opening as point IV. tool 90° before beginning with the measuring procedure. – The difference d of both marked points III and IV results in the actual deviation of the Doubled height of the door opening x 0.0024 tool to the plumb line.
-
Page 18: Maintenance And Service
Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all Bosch lasers and measuring tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase. Bosch will extend warranty coverage to two (2) years when you register your product within eight (8) weeks after date of purchase.