1. Manuals
  2. Brands
  3. HP Manuals
  4. Server
  5. 9000 rp7420
  6. Installation manual

HP 9000 rp7420 Installation Manual

Hp 9000 rp7420 server installation guide
Hide thumbs Also See for 9000 rp7420:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual

Installation Guide

HP 9000 rp7420 Server
Fourth Edition
Manufacturing Part Number : A7025-96014
October 2006
Printed in the U.S.A.
© Copyright 1979-2006 Hewlett-Packard Development Company, L.P.

Advertisement

Table of Contents
loading

Related Manuals for HP 9000 rp7420

Summary of Contents for HP 9000 rp7420

  • Page 1: Installation Guide

    Installation Guide HP 9000 rp7420 Server Fourth Edition Manufacturing Part Number : A7025-96014 October 2006 Printed in the U.S.A. © Copyright 1979-2006 Hewlett-Packard Development Company, L.P.

  • Page 2: Legal Notices

    The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

  • Page 3: Table Of Contents

    Internal Disk Devices for the HP 9000 rp7420 Server ....... .
  • Page 4 Contents Index ............... 67...
  • Page 5 Table 3-1. HP 9000 rp7420 Server PCI-X I/O Cards ....... .
  • Page 6 Tables...
  • Page 7 Figures Figure 1-1. HP 9000 rp7420 Server with mounted bezel (Front View) ......3 Figure 1-2. Right-Front View of HP 9000 rp7420 Server ........5 Figure 1-3.
  • Page 8 Figures viii...

  • Page 9: Introduction

    HP 9000 rp7410 product. The HP 9000 rp7420 Server shares the same hardware as the HP 9000 rp7410 with changes to the cell board, CPU modules, core I/O, and the PCI-X backplane.

  • Page 10: Overview

    Overview Overview The HP 9000 rp7420 Server is a 10U, 8-socket Symmetric Multi-Processing, rack-mount server that accommodates up to 64 GB of memory; PCI-X I/O, and internal peripherals, including disks and DVD/tape. Its high availability features include N+1 hot-pluggable fans and power, redundant power cords, and hot-pluggable PCI-X cards and internal disks.

  • Page 11: Figure 1-1 Hp 9000 Rp7420 Server With Mounted Bezel (Front View)

    Introduction Overview Figure 1-1 HP 9000 rp7420 Server with mounted bezel (Front View) • Depth: Defined by cable management constraints to fit into standard 36-inch deep racks: 25.5 inches from front rack column to PCI connector surface 26.7 inches from front rack column to MP Core I/O connector surface 30 inches overall package dimension, including 2.7 inches protruding in front of the front rack columns...
  • Page 12 Introduction Overview See Figure 1-2 on page 5 for component location. The mass storage section located in the front allows access to the hard disk drives without removal of the bezel (bezel removed in figure). Removing the bezel allows access to the removable media drive, the front fans and the bulk power supplies.

  • Page 13: Figure 1-2 Right-Front View Of Hp 9000 Rp7420 Server

    Introduction Overview Figure 1-2 Right-Front View of HP 9000 rp7420 Server PCI/PCI-X slots PCI-X fan Hard Disk modules Drives Front panel Cell 0 display board Cell 1 Removable Media PCI Power modules Front fans Bulk powers supplies Chapter 1...

  • Page 14: Figure 1-3 Left-Rear View Of Hp 9000 Rp7420 Server

    The two redundant MP/SCSI Core I/O cards are positioned vertically, one above the other, at the rear of the chassis. Redundant power line cords attach to the AC power receptacles at the bottom rear. Two 20-amp cords are required to power the HP 9000 rp7420 server. Two additional 20-amp cords provide redundancy. Chapter 1...

  • Page 15: Front Panel

    (PDH) and micro controller hardware. Each cell board holds up to 16 DIMMs. There can be one or two cell boards installed in an HP 9000 rp7420 server. A cell board can be selectively powered down for cell replacement without affecting the other cell in another configured partition.

  • Page 16: I/O Subsystem

    Introduction Overview I/O Subsystem All of the I/O is integrated into the system by way of the PCI-X buses. The CC on each cell board communicates with one system bus adapter (SBA). The SBA converts the SBA link protocol into “ropes”. A rope is defined as a high-speed, point-to-point data bus.

  • Page 17: Mp/Scsi Core I/O Board

    MP/SCSI Core I/O Board The HP 9000 rp7420 Server accommodates two sets of core I/O functionality. Each core I/O board set consists of a MP/SCSI Core I/O board and a Procurium LAN/SCSI board. At least one MP/SCSI Core I/O board inserted in slot 1 is required (independent of partitions).

  • Page 18: Internal Disk Devices For The Hp 9000 Rp7420 Server

    Internal Disk Devices for the HP 9000 rp7420 Server In an HP 9000 rp7420 Server, the top internal disk drives connect to cell 1 through the core I/O for cell 1. Both of the bottom disk drives connect to cell 0 through the core I/O for cell 0.

  • Page 19: Unpacking The Server

    Unpacking the Server Inspect shipping containers when the equipment arrives at the site. Check equipment after the packing has been removed. This chapter discusses how to inspect and receive the HP 9000 rp7420 server. Chapter 2...

  • Page 20: Inspecting The Server Cabinet

    HP shipping containers are designed to protect their contents under normal shipping conditions. After the equipment arrives at the customer site, carefully inspect each carton for signs of shipping damage. A tilt indicator is installed on each carton shipped.

  • Page 21: Receiving The Server Cabinet

    Unpacking the Server Receiving the Server Cabinet Receiving the Server Cabinet This section contains information about unpacking the cabinet. WARNING Wear protective glasses while cutting the plastic bands around the shipping container. These bands are under tension. When cut, they can spring back and cause serious eye injury.

  • Page 22: Figure 2-2 Removing The Shipping Bolts And Plastic Cover

    Unpacking the Server Receiving the Server Cabinet Step 4. Remove the packing materials. CAUTION To reduce any ESD exposure, cut off the plastic wrapping around the cabinet. DO NOT pull it off the cabinet. Step 5. Remove the bolts that hold the ramps to the pallet, and remove the ramps. See Figure 2-2. Figure 2-2 shows one ramp attached to the pallet on either side of the cabinet with NOTE each ramp secured to the pallet using two bolts.

  • Page 23: Figure 2-3 Preparing To Roll Off The Pallet

    Unpacking the Server Receiving the Server Cabinet Step 6. Remove the six bolts from the base attaching the rack to the pallet. See Figure 2-3 Figure 2-3 Preparing to Roll Off the Pallet Use caution when rolling the cabinet off the ramp. A single 2-cell server in WARNING the cabinet weighs approximately 220 lb.

  • Page 24: Securing The Cabinet

    Unpacking the Server Receiving the Server Cabinet Securing the Cabinet When in position, secure and stabilize the cabinet, using the leveling feet at the corners of the base. Follow the instructions in rack documentation to install the anti-tip mechanisms on the bottom front and rear of the rack.

  • Page 25: Stand Alone And To Be Racked Systems

    Rack Mount System Installation There are several documents written to help with rack mounting the server. This list is intended to guide the HP Installation Specialist to the documentation that has been written by the Rack Solutions team. The external website is http://h18004.www1.hp.com/products/servers/proliantstorage/bcs-rackandpower/index.html.

  • Page 26: Manual Lifting

    Manual Lifting Use this procedure only if a HP approved lift is not available. This procedure should only be performed by two qualified HP Service Personnel utilizing proper lifting techniques and procedures. System damage can occur through improper removal and re-installation of devices. This task must be performed by trained personnel only.

  • Page 27: Figure 2-5 Positioning The Lift Handles

    Unpacking the Server Manual Lifting Step 6. Insert the pins of the panel into the rear of the front rack mount flange of the chassis. See Figure 2-5. (Cell boards are shown installed in figure.) Figure 2-5 Positioning the Lift handles Pins Chapter 2...

  • Page 28: Figure 2-6 Inserting The Shoulder Washer Pins Into The Server Chassis

    Unpacking the Server Manual Lifting Step 7. Pull the spring plunger out and move the handles apart. Install the shoulder washer end of the panel into the keyways at the rear of the server chassis. See Figure 2-6. (Cell boards shown installed in figure.) Figure 2-6 Inserting the Shoulder Washer Pins Into the Server Chassis Step 8.

  • Page 29: Figure 2-7 Lift Handles Mounted

    Step 11. To lift the server, two individuals may rotate the handles 90 degrees to the horizontal position and grasp. NOTE To ensure proper installation, refer to the “Installation Guide” of the HP J1530B Rack Integration Kit. Step 12. After moving the server, remove the lift handle panels from the chassis.

  • Page 30: Using The Roni Model 17000 Sp 400 Lifting Device

    Documentation for the RonI lifter has been written by RonI and is on the HP intranet at the Cybrary Web site. Complete details on how to assemble the lifter, troubleshoot the lifter, and maintain the lifter are provided by RonI in the documentation.

  • Page 31: Figure 2-9 Server With Shipping Box Removed

    Unpacking the Server Using the RonI Model 17000 SP 400 Lifting Device Step 1. Obtain the HP J1530B Rack Integration Kit Installation Guide before proceeding with the rack-mount procedure. This guide covers these important steps: • Installing the anti-tip stabilizer kit (A5540A) •...

  • Page 32: Figure 2-10 Remove Cushions For Lift Access

    Unpacking the Server Using the RonI Model 17000 SP 400 Lifting Device Step 4. Remove the two foam cushions for lift access as shown in Figure 2-10. Figure 2-10 Remove Cushions for Lift Access Remove Cushions Clearance for RonI lift is 28”...

  • Page 33: Figure 2-11 Raising A Server Off The Pallet

    Figure 2-11 Raising a Server Off the Pallet Step 7. Roll the lifter and server away from the pallet. Step 8. Follow the HP J1530B Rack Integration Installation Guide to complete these steps: • Mounting the server to the slides.

  • Page 34: Wheel Kit Installation

    Unpacking the Server Wheel Kit Installation Wheel Kit Installation Compare the packing list with the contents of the wheel kit before beginning the installation. Table 2-1 Wheel Kit Packing List Part Number Description Quantity A6753-04013 Wheel Kit consisting of the following components: A6753-04002 Right side caster cover...

  • Page 35: Figure 2-12Component Locations

    Unpacking the Server Wheel Kit Installation Step 1. Cut and remove the polystrap bands securing the server to the pallet. Step 2. Lift the cardboard top from the cardboard tray resting on the pallet. Step 3. Remove the bezel kit carton and the top cushions from the pallet. Figure 2-12Component Locations Top Cushions Cardboard Tray...

  • Page 36: Figure 2-13Left Foam Block Position

    Unpacking the Server Wheel Kit Installation Step 5. Carefully tilt the server and place one of the foam blocks (A6093-44002) under the left side of the server. Do not remove any other cushions until instructed to do so. Figure 2-13Left Foam Block Position Foam Block Cardboard Tray Step 6.

  • Page 37: Table 2-2 Caster Part Numbers

    Unpacking the Server Wheel Kit Installation Step 7. Remove the cushions from the lower front and rear of the server. Do not disturb the side cushions. Figure 2-15Foam Block Removal Step 8. Locate and identify the caster assemblies. Use the following table to identify the casters. NOTE The caster part number is stamped on the caster mounting plate.

  • Page 38: Figure 2-16Attaching A Caster To The Server

    Unpacking the Server Wheel Kit Installation Step 9. Locate and remove one of the four screws from the plastic pouch. Attach a front caster to the server. Figure 2-16Attaching a Caster to the Server Front Casters Step 10. Attach the remaining casters to the server using the screws supplied in the plastic pouch. Step 11.

  • Page 39: Figure 2-17. Securing Each Caster Cover To The Server

    Unpacking the Server Wheel Kit Installation Step 16. Insert the slot on the caster cover into the front caster. Secure the cover to the server by tightening the captive screw on the cover at the rear of the server. Figure 2-17 Securing Each Caster Cover to the Server Right Caster Cover Rear Casters...

  • Page 40: Figure 2-18 Completed Server

    Unpacking the Server Wheel Kit Installation Step 18. Wheel kit installation is complete when both caster covers are attached to the server, all covers are installed and the front bezel is mounted. Figure 2-18 Completed Server Attached Caster Cover Chapter 2...

  • Page 41: Installing Accessories

    Installing Accessories The following options may be installed in the HP 9000 rp7420 server: • additional hard disk drive storage • removable media device storage • PCI and PCI-X I/O cards Chapter 3...

  • Page 42: Installing Add-On Products

    See Figure 3-1. A list of replacement disk drives for the HP 9000 rp7420 server is in Appendix A of the Service Guide for the HP 9000 rp7420 server. The list contains both removable media disk drives and hard disk drives.
  • Page 43 Refer to “Shutting Down nPartitions and Powering OFF Hardware Components” in the Service Guide for the HP 9000 rp7420 server for more information. Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD CAUTION safety precautions could result in damage to the HP 9000 rp7420 server.

  • Page 44: Pci/Pci-X Card Cage Assembly I/O Cards

    PCI/PCI-X Card Cage Assembly I/O Cards PCI/PCI-X Card Cage Assembly I/O Cards A number of PCI and PCI-X I/O cards are supported in the HP 9000 rp7420 Server. Known cards supported at the release of this manual are shown in Table 3-1.
  • Page 45 64-port Terminal MUX PCI I/O Card Installation HP 9000 rp7420 Servers implement Manual Release Latch (MRL) hardware for use in online add or replacement (OLAR) operations. If an MRL is left open while the server is booting, HP-UX can incorrectly cache PCI slot power status causing OLAR operations to fail.
  • Page 46 IMPORTANT The installation process varies depending on what method for installing the PCI card is selected. PCI I/O card installation procedures should be downloaded from the http://docs.hp.com/ Web site. Background information and procedures for adding a new PCI I/O card using online addition are found in the Interface Card OL* Support Guide.

  • Page 47: Figure 3-2 Pci I/O Slot Details

    Installing Accessories PCI/PCI-X Card Cage Assembly I/O Cards Step 1. Remove the top cover. Step 2. Remove the PCI bulkhead filler panel. Step 3. Lever open the Manual Retention Latch for selected slot. Refer to Figure 3-2. Step 4. Install the I/O card in the slot. NOTE A slow, firm pressure is needed to properly seat the card into the backplane.
  • Page 48 For finer control over CRA actions use pdweb or the olrad command. Refer to the Interface Card OL* Support Guide located on the Web at http://docs.hp.com for details. Step 9. Replace the top cover.

  • Page 49: Cabling And Power Up

    Cabling and Power Up After the system has been unpacked and moved into position, it must be connected to an AC power source. The AC power must be checked for the proper voltage before the system is powered up. This chapter describes these activities.

  • Page 50: Voltage Check

    Procedure).” Preface The HP 9000 rp7420 Server requires a minimum of 2 power cords. To enable full power redundancy, 4 power cords may be used. When using 4 power cords, dual power sources may be used to provide additional power source protection.

  • Page 51: Table 4-1. Single Phase Voltage Examples

    Figure 4-1 Voltage Reference Points for IEC 320 C19 Plug IMPORTANT These measurements must be performed for every power cord that plugs into the HP 9000 rp7420 Server. Step 1. Measure the voltage between L1 and L2. This is considered to be a phase-to-phase measurement in North America.

  • Page 52: Figure 4-2 Safety Ground Reference Check-Single Power Source

    Cabling and Power Up Voltage Check Safety Ground Verification (Single Power Source) This procedure measures the voltage level between A0 and A1. The voltage level between B0 and B1 will also be verified. All measurements will be taken between ground pins. See Figure 4-2 for ground reference points when performing these measurements.

  • Page 53: Figure 4-3 Safety Ground Reference Check-Dual Power Source

    Cabling and Power Up Voltage Check Safety Ground Verification (Dual Power Source) This procedure measures the voltage level between A0 and A1, between B0 and B1, between A0 and B0, and between A1 and B1. All measurements will be taken between ground pins. See Figure 4-3 for ground reference points when performing these measurements.

  • Page 54: Voltage Check (Additional Procedure)

    If a UPS is used, refer to applicable UPS documentation for information to connect the server and to check the UPS output voltage. UPS User Manual documentation is shipped with the UPS. Documentation can also be found at http://www.hp.com/racksolutions. Step 1. Verify that site power is Step 2.
  • Page 55 Cabling and Power Up Voltage Check (Additional Procedure) Do not set site AC circuit breakers serving the processor cabinets to WARNING before verifying that the cabinet has been wired into the site AC power supply correctly. Failure to do so might result in injury to personnel or damage to equipment when AC power is applied to the cabinet.

  • Page 56: Connecting Ac Input Power

    Cabling and Power Up Connecting AC Input Power Connecting AC Input Power The server can receive AC input power from two different AC power sources. If two separate power sources are available as depicted in Figure 4-6 on page 49, the server can be plugged into the separate power sources, increasing system reliability should one power source fail.

  • Page 57: Figure 4-6. Power Source Versus. Power Distribution

    Cabling and Power Up Connecting AC Input Power Select Option: Figure 4-6 Power Source versus. Power Distribution BPS 0 BPS 1 Power Source A Power Source B *180-269 VAC Voltage is present at various locations within the server whenever a power source is WARNING connected.

  • Page 58: Mp/Scsi Core I/O Connections

    MP/SCSI Core I/O Connections Each HP 9000 rp7420 Server can have up to two core I/O board sets installed, which allows two partitions to operate, or MP/SCSI Core I/O redundancy in a single partition configuration. Each core I/O board set consists of two boards: the MP/SCSI Core I/O board and the LAN/SCSI board.

  • Page 59: Setting Up The Customer Engineer Tool (Pc)

    Setting Up the Customer Engineer Tool (PC) The Customer Engineer (CE) Tool is usually a laptop. It allows communication with the MP in the HP 9000 rp7420 Server. The MP monitors the activity of either a one partition or a multiple-partition configuration.

  • Page 60: Connecting The Ce Tool To The Local Rs232 Port On The Mp

    Cabling and Power Up Setting Up the Customer Engineer Tool (PC) If the CE Tool is a laptop using Reflection 1, ensure communications settings are in place, using the following procedure: 1. From the Reflection 1 Main screen, pull down the Connection menu and select Connection Setup. •...

  • Page 61: Turning On Housekeeping Power And Logging In To The Mp

    1. Connect the server to AC power. On the front of the HP 9000 rp7420 Server, a solid green Standby Power LED, a solid green MP Present LED, and a flashing amber Attention LED will illuminate after about 30 seconds.

  • Page 62: Figure 4-7 Mp Main Menu

    Cabling and Power Up Turning on Housekeeping Power and Logging in to the MP The MP Main Menu is displayed: Figure 4-7 MP Main Menu Chapter 4...

  • Page 63: Configuring Lan Information For The Mp

    Cabling and Power Up Configuring LAN Information for the MP Configuring LAN Information for the MP This section describes how to set and verify the server MP LAN port information. LAN information includes the MP network name, the MP IP address, the subnet mask, and gateway address. This information is provided by the customer.

  • Page 64: Figure 4-9The Ls Command Screen

    This is the host name for the MP LAN. The name can be as many as 64 characters in length, and include alphanumeric characters, - (dash), _ (under bar), . (period), or a space. HP recommends that the name be a derivative of the complex name. For example, Acme.com_MP.

  • Page 65: Accessing The Management Processor Via A Web Browser

    The MP/SCSI Core I/O card has a separate LAN port from the system LAN port. It requires a separate LAN drop, IP address, and networking information from that of the port used by HP-UX. Before starting this procedure, the following information is required: •...

  • Page 66: Figure 4-11 Browser Window

    Cabling and Power Up Accessing the Management Processor via a Web Browser Step 7. Launch a Web browser on the same subnet using the IP address for the MP LAN port. Figure 4-11 Browser Window Zoom In/Out Title Bar Step 8. Select the emulation type you want to use. Step 9.

  • Page 67: Verifying Presence Of The Cell Boards

    Cabling and Power Up Verifying Presence of the Cell Boards Verifying Presence of the Cell Boards To perform this activity, either connect to the MP using a console, or connect the CE Tool (laptop) to the RS-232 Local port on the MP/SCSI Core I/O. After logging in to the MP, verify that the MP detects the presence of all the cells installed in the cabinet.

  • Page 68: Booting The Hp 9000 Rp7420 Server

    If a LAN connection to the MP/SCSI Core I/O is available, review server activity for each partition configured, while the server powers up and boots. Windows can be opened for the complex and for each partition. HP recommends that at least two windows be opened: 1.

  • Page 69: Selecting A Boot Partition Using The Management Processor

    Booting HP-UX using Boot Console Handler If Instant Ignition was ordered, HP-UX will have been installed in the factory at the Primary Path address. If HP-UX is at a path other than the Primary Path, use the pa (path) command (from the Configuration Menu) to set boot path.

  • Page 70: Adding Processors With Instant Capacity On Demand

    These iCOD CPUs reside in the purchased system, but they belong to HP and therefore are HP assets. A nominal “Right-To-Access Fee” is paid to HP for each iCOD processor in the system. At any time, any number of iCOD CPUs can be “activated.” Activating an iCOD CPU automatically and instantaneously transforms the iCOD CPU into an instantly ordered and fulfilled CPU upgrade that requires payment.

  • Page 71: Using The Checklist

    Cabling and Power Up Using the Checklist Using the Checklist The following checklist is an installation aid and should be used only after you have installed several systems using the detailed procedures described in the body of this manual. This checklist is a compilation of the tasks described in this manual, and is organized as follows: PROCEDURES The procedures outlined in this document in order IN-PROCESS...
  • Page 72 Cabling and Power Up Using the Checklist Table 4-2 Factory-Integrated Installation Checklist (Continued) (Continued) PROCEDURE IN-PROCESS COMPLETED Initials Comments Initials Comments Unpack other equipment Remove and dispose of packaging material Move cabinet(s) and equipment to computer room Install non-factory, integrated I/O cards (if required) Move cabinets into final position...
  • Page 73 Cabling and Power Up Using the Checklist Table 4-2 Factory-Integrated Installation Checklist (Continued) (Continued) PROCEDURE IN-PROCESS COMPLETED Initials Comments Initials Comments Verify remote link (if required) Select PCI card slot Install PCI card Verify installation Route cables using the cable management arm Install other peripherals (if required)
  • Page 74 Cabling and Power Up Using the Checklist Chapter 4...
  • Page 75 SP Active Standby Power Good Lift Handle backplane login name mass storage ls (LAN status) command system booting HP-UX BPS (Bulk Power Supply) MAC address bulk power supply Management Processor (MP) mass storage mass storage backplane cell board verifying presence...
  • Page 76 Index unpacking inspecting for damage verifying system configuration voltage check...

Table of Contents