Yamaha 01x Service Manual page 81

displayed on the LCD. The page can be changed among "FADER
AGING (COUNT), FADER AGING (MOVE MEASURE) and
FADER AGING (FADER RANK) by pressing the [DISPLAY
DOWN/UP] button.
30:FADER AGING (COUNT)
COUNT=xxxxxxx
When the [DISPLAY DOWN] button is pressed once, the LCD
appears as shown below. Figures show the time required for
each fader to move 20mm (1/3 stroke) from the moment it starts
to move in miliseconds. Displayed at the upper right of the LCD
is the moving time of the STEREO fader. If the moving time is
999msec or longer, 999 is used. RANGE=xxx is the difference
with the shortest moving time subtracted from the longest one.
30:FADER AGING(MOVE MEASURE)
350 370 381 360
When the [DISPLAY DOWN] button is pressed once again, the
LCD appears as shown below. Displayed on it are the fader
speed setting parameters and the fader ranks (graded in 15 steps
0: light - 14: heavy) and displayed at the upper right is the fader
rank of the STEREO fader. (The fader speed can be changed by
turning [KNOB-7] but usually it is kept unchanged at 28 because
changing it may result in a large variation of the fader speed
within the same model.)
30:FADER AGING(FADER RANK)
4 3 4
To end execution, press [KNOB-8] in the FADER AGING
(COUNT) page. Then the set FADER SPEED parameter is saved
in the memory.
(3) Execution method in the faulty state
If 4.22 FADER LEVEL adjustment has not been executed, the
following message is displayed and it is not possible to execute
this check.
30:FADER AGING
ERROR:NOT EXECUTE (22)FADER LEVEL
When ERROR appears on the LCD, press [KNOB-8] and testing
comes to an end. The screen returns to the execution select screen
and "X" is displayed in the check item space.
30:FADER AGING
ERROR:xxxxxx
(4) Item description and error message
1: NOT EXECUTE
EXIT
RANGE=80
390 320 400
FADER SPEED = 28
4 5 4 4
EXIT
EXIT
ERROR message: ERROR: NOT EXECUTE (22)
FADER LEVEL
As the FADER LEVEL adjustment has not been
executed, it is not possible to execute this test.
2: CAN NOT SAVE
ERROR message: ERROR: CAN NOT SAVE
Saving in the Flash ROM is not possible.
(5) Check point when judged as NG
None
4.25 DSP PATCH connection ......
(1) Outline
The DSP patch required for the hardware verification work is
355
provided. The LCD appears as shown below and the patch can
350
be varied by turning [KNOB-1], [KNOB-3] and [KNOB-5].
31:DSP PATCH
AD14->DA14
(2) Execution method in the normal state
Select the signal to be output to DA14 (DA12, DA34) by turning
[KNOB-1]. It is possible to make following settings.
"AD14->DA14": AD1-4 is output to DA1-4.
"AD58->DA14": AD5-8 is output to DA1-4.
"D.IN->DA12": Digital In is output to DA1-2, DA3-4 is
5
4
"D.IN->DA34": Digital In is output to DA3-4, DA1-2 is
The signal to be output to D.OUT can be varied by turning
[KNOB-3]. It is possible to make following settings.
"AD12->D.OUT":
"AD34->D.OUT":
"AD56->D.OUT":
"ADA78->D.OUT:
FS when using the built-in clock can be selected by turning
[KNOB-5].
"INT48K"->Built-in clock FS 48kHz is used.
"INT96K"->Built-in clock FS 96kHz is used.
To terminate the operation, press [KNOB-8].
(3) Execution method in the faulty state
None
(4) Item description and error message
None
(31) DSP PATCH
AD12->DOUT INT48K
muted and Digital In becomes the word
clock master.
muted and Digital In becomes the word
clock master.
AD1-2 is output to Digital Out.
AD3-4 is output to Digital Out.
AD5-6 is output to Digital Out.
AD7-8 is output to Digital Out.
O1X
EXIT
81