The interlock mechanism mentioned above becomes invalid in this mode. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 49. DV-360-S...
Page 3
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. DV-360-S...
7.1.7 ID NUMBER AND ID DATA SETTING....................62 7.1.8 SEQUENCE AFTER POWER ON ......................65 7.1.9 DISASSEMBLY ............................. 66 7.2 IC ................................73 7.3 DISC / CONTENT FORMAT PLAYBACK COMPATIBILITY ..............87 7.4 CLEANING............................... 90 8. PANEL FACILITIES ............................91 DV-360-S...
Dolby Laboratories. • “DTS” and “DTS Digital Out” are registered trademarks of Digital Theater Systems, Inc. • TruSurround and the symbol are trademarks of SRS Labs, Inc. TruSurround tech- nology is incorporated under license from SRS Labs, Inc. DV-360-S...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING WVXCN Type Only WYXCN and WYXCN/FG Types Only "Operating Instructions" DV-360-S...
Page 7
(French / German) Operating Instructions See Contrast table (2) (Spanish / Dutch) NSP 10 Warranty Card ARY7065 (2) CONTRAST TABLE DV-360-S/WYXCN, WYXCN/FG, WVXCN, DV-360-K/WYXCN and WYXCN/FG are constructed the same except for the following : DV-360-S/ DV-360-S/ DV-360-S/ DV-360-K/ DV-360-K/ Mark No.
2.2 EXTERIOR SECTION Refer to "2.4 LOADING MECHA. ASSY". Refer to "2.3 FRONT PANEL SECTION". DV-360-S...
Page 9
Label VRW1872 NSP 11 Base Chassis VNA2562 Rear Panel See Contrast table (2) (2) CONTRAST TABLE DV-360-S/WYXCN, WYXCN/FG, WVXCN, DV-360-K/WYXCN and WYXCN/FG are constructed the same except for the following : DV-360-S/ DV-360-S/ DV-360-S/ DV-360-K/ DV-360-K/ Mark No. Symbol and Description...
Page 11
Screw PPZ30P080FMC Connector Assy (4P) VKP2298 FP Angle VNE2297 Rubber Foot VEB1349 (2) CONTRAST TABLE DV-360-S/WYXCN, WYXCN/FG, WVXCN, DV-360-K/WYXCN and WYXCN/FG are constructed the same except for the following : DV-360-S/ DV-360-S/ DV-360-S/ DV-360-K/ DV-360-K/ Mark No. Symbol and Description...
JGZ17P028FMC Screw Z39-019 Flexible Cable (24P) VDA1945 Tray VNL1920 Connector Assy 2P VKP2253 Floating Rubber VEB1351 Belt VEB1330 Stabilizer VNE2253 Loading Base VNL1917 Float Base DVD VNL1918 Drive Cam VNL1919 Gear Pulley VNL1921 Loading Gear VNL1922 Drive Gear VNL1923 DV-360-S...
Page 13
Rear View Daifree Daifree No. 23 No. 23 GEM1036 GEM1036 Tray Tray Concave of unevenness Concave of unevenness Inner side of a ditch Daifree GEM1036 Top View Bottom View Side of the rib Concave of unevenness Daifree Daifree GEM1036 GEM1036 DV-360-S...
3.3 LOAB ASSY and OVERALL WIRING DIAGRAM Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST". POWER SUPPLY UNIT (VWR1366) ( or VWR1368) DVDM ASSY (VWS1556) SCRB ASSY (VWV1934) DV-360-S...
Page 21
: FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE FLKY ASSY IRKY ASSY (VWG2408) (VWG2415) PICKUP ASSY-S (OXX8005) SPINDLE STEPPING MOTOR MOTOR : VXM1101 : VXM1099 LOADING MOTOR ASSY : VXX2872 LOAB ASSY (VWG2426) DV-360-S...
Page 25
: V SIGNAL ROUTE : S-VIDEO OUT C/C SIGNAL ROUTE S-C/C B/Cb S-Y/Y : S-VIDEO OUT Y/Y SIGNAL ROUTE S-Y/Y : R/Cr SIGNAL ROUTE R/Cr : G/Y SIGNAL ROUTE : B/Cb SIGNAL ROUTE B/Cb : AUDIO SIGNAL ROUTE : AUDIO(DIGITAL) SIGNAL ROUTE DV-360-S...
Page 27
: V SIGNAL ROUTE : S-VIDEO OUT C/C SIGNAL ROUTE S-C/C : S-VIDEO OUT Y/Y SIGNAL ROUTE S-Y/Y B/Cb : R/Cr SIGNAL ROUTE R/Cr R/Cr : G/Y SIGNAL ROUTE : B/Cb SIGNAL ROUTE B/Cb : AUDIO SIGNAL ROUTE : AUDIO(DIGITAL) SIGNAL ROUTE DV-360-S...
Page 33
: V SIGNAL ROUTE : S-VIDEO OUT C/C SIGNAL ROUTE S-C/C : S-VIDEO OUT Y/Y SIGNAL ROUTE S-Y/Y : R/Cr SIGNAL ROUTE R/Cr : G/Y SIGNAL ROUTE : B/Cb SIGNAL ROUTE B/Cb : AUDIO SIGNAL ROUTE DV-360-S...
SIDE B Chip Part P.C.Board transistor Resistor array 3-terminal regulator SIDE A SIDE B LOAB ASSY (VNP1910-A) LOAB S101 LOAD+ VWG2426- CN602 CN602 C102 LOAD- PYKC F6 VNP1910- C101 CN601 CN601 CN602 CN601 CN601 CN602 CN103 LOADING MOTOR ASSY DV-360-S...
CONTAINS LEAD IN SOLDER AND CERTAIN ELECTRICAL PARTS WARNING CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. IC101 IC301 IC400 IC404 IC603 IC604 IC403 IC601 IC602 Q403 Q390 Q211 Q201 Q202 Q405 Q402 Q603 Q212 Q404 Q401 DV-360-S...
[Electrical Part] screw screw Electrical adjustments are not required. 6.2 JIGS AND MEASURING INSTRUMENTS Test mode remote control Screwdriver (large) Screwdriver (medium) TV monitor unit (GGF1067) Screw tight (GYL1001) DVD test disc Precise screwdriver Soldering iron (GGV1025) DV-360-S...
Purpose: To set the sweep which was correct with the individual Traverse mechanism. Be sure to perform the following step finally when replaced Pickup, Traverse Mechanism and Spindle Motor. CLEAR GGF1067 Test mode remote control unit (It is necessary when performed adjustment procedure Ÿ.) DV-360-S...
Perform only trace, video and audio outputs are nothing. < When playback with the target address of disc (DVD)> For example, when playback with # 30000 During PLAY CHP/TIM Press keys in order 030000 TEST MODE: OFF POWER GGF1067 Test mode remote control unit DV-360-S...
(Refer to "6.1 ADJUSTMENT ITEMS AND LOCATION".) Spacer for Height adjustment Note: Turn a flat side into bottom Before removing the flexible cable for the pickup, soldering of the pickup circuit is necessary. For details, see "7.1.9 DISASSEMBLY". DV-360-S...
J : Min Disc playback normally. If error rate is OK, • The measurement of block error rate locks a root of tangential and radial adjustment screws with the Screw tight, and go to step Screw tight: GYL1001 Test mode end DV-360-S...
Page 52
Initialize the Focus Sweep Setting Purpose: To set the sweep which was correct with the individual Traverse mechanism. Turn on the Player POWER CLEAR Note: Be sure to perform this step when replaced the Pickup or Traverse mechanism. DV-360-S...
Perform only trace, video and audio outputs are nothing. = Screen display ON/OFF 1. Turn off the display by pressing the [AUDIO] (A8-1E) key of the remote control unit. 2. Turn on the display by pressing the [DISPLAY] (A8-43) key of the remote control unit. DV-360-S...
Page 54
• After the search, perform only trace and video and audio outputs are nothing. 4. Release the Search address input • Clear the address by pressing the [CLEAR] (A8-45) key. Release the address input mode when pressing the [CLEAR] key once again. DV-360-S...
Kinds of version / firmware of the FE. Scart terminal output [SK – ∗ ∗] RAM or ROM (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-360-S...
• Region confirmation mode (ESC + AUDIO [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys) After you press the AUDIO key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-360-S...
(version of ST core software) softwareVersion . softwareRevision / buildNumber 0 F.E VERSION Version of FRONT END (version of mechanism controller CHIP software) MainVersion / Kinds of firmware RAM or ROM - Remote control code = Key code of Main unit DV-360-S...
PLL lost timeout 0x93 DECODER ERROR 0xa∗ DECODER TIMEOUT 0xb∗ Note : 0 x & & ID lost error 0xa3 ID lost timeout 0xb3 DEVICE ERROR 0xd∗ code SRAM error 0xd1 (Only this part is displayed to a display) DV-360-S...
Do move to inner and outer periphery 1. Stepping motor of the stepping in the test mode? 2. Inside switch Stepping move timeout 0 x 54 Did timeout at stepping movement Do indicate "S-04" at the most inner 3. Driver periphery of the stepping? DV-360-S...
Page 61
SRAM error 0 x d1 Cannot access SRAM 2. Front End IC Is not bus line short-circuiting? 3. Front End-SRAM bus line FAILSAFE (0 x e∗) 1. software runaway Unexpected error 0 x e1 Unexpected error 3. Software bug DV-360-S...
(The SEARCH key is not accepted after all 9 digits have been entered.) Input ID Number ! [Player's ID Number Setting] ID Number ? > 0 0 0 0 0 0 0 0 1 OK ? <PLAY> Compare Mode <SEARCH> Enter Input ID Number ! DV-360-S...
Page 63
[Player's ID Number Setting] ID Number ? [ 0 0 0 0 0 0 0 0 1 ] Compare > 0 0 0 0 0 0 0 0 1 OK? <PLAY> Enter <STOP> Memory Clear Input ID Number ! DV-360-S...
Page 64
• Indication when the data have not been set If no ID data are set after the ID number is changed, the message "NO ID DATA" flashes on the screen and FL display for a few seconds after the power is turned on or during Stop mode. DV-360-S...
BACK END (FP_XRDY) [BACK END] Outputs the communicable signal to FL controller (FP_ACK) BACK END – FL controller communication The opening picture appears [FRONT END] Check the following: • Slider positioning (INSIDE SW) • Spindle FG stop Disc detection (Focus control) DV-360-S...
Gear in the Loading Mecha. Assy in the direction of the arrow, as indicated in the photo. If the Tray pops out a little, fully pull it out by hand. Screwdriver (small) Projection Slit Drive Gear Loading Mecha.Assy Tray open Screwdriver (small) DV-360-S...
Page 67
Remove the six hooks. Remove the front panel section. ×2 DVDM Assy 1 1 1 Remove the four screws. Remove the three screws. ×3 DVDM Assy DVDM Assy Remove the DVDM Assy and stand it against the other parts. DV-360-S...
Page 68
Mecha. Assy to the unit. Bridge Tray Drive Cam Note when reinserting the Tray When reinserting the Tray, first align the triangle printed on the Loading Base and the pin of the Drive Cam, then insert the Tray. Front Side Loading Base Triangle DV-360-S...
Page 69
Dislodge the flexible cables from their factory for the spindle motor Front Side placement. Flexible cable Flexible cable for the pickup for the stepping motor Bottom View Remove the four hooks. Traverse Mecha. Assy-S × 2 Remove the Traverse Mecha. Assy-S. × 2 DV-360-S...
Page 70
Remove the flexible cable for the pickup. Flexible cable for the pickup Bottom View Adjustment screw Adjustment screw Remove the two adjustment screws and two adjustment springs. (Skew screw) (Skew screw) Remove the Pickup Assy-S. Pickup Assy-S Adjustment spring (Skew spring) Adjustment spring (Skew spring) DV-360-S...
Page 71
Joint Spring Silicone Adhesive GEM1037 Joint 03 Silicone Adhesive GEM1037 Arrangement of the flexible cable Arrangement of the flexible cable for the spindle motor for the stepping motor : Conductive surface : Conductive surface Hook Hook Bottom View Bottom View DV-360-S...
Page 72
Reference line Hook Fold the flexible cable as indicated in the photo. Fold the flexible cable along the hook. Hook the part folded in Step 1 to the hook. Reference Hook Pass the cable below the hook line Hook DV-360-S...
Page 73
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. • List of IC STM6316ATXXA, STM5589CVA, M63108FP, PE5374A 7 STM6316ATXXA (DVDM ASSY : IC301) • FRONT END IC ¶ Block Diagram DV-360-S...
Page 74
¶ Pin Function t i c t i c t s i t s i t s i t s i t s i t i s t i s DV-360-S...
Page 75
- t l l i c y t i - t l l i c y t i - t l l i c y t i d l l DV-360-S...
Page 85
Destination (of player) Select (Set with a combinaition of this 3 ports) MS1_0 H" : No System Reset mode , "L" : General mode H" : OEM Model , "L" : Pioneer Model MIC IN Detection of Microphone "H" : Microphone connected CHECKER H"...
Other formats, including but not limited to the • This unit will play DVD-RW discs recorded following, are not playable in this player: using the Video Recording (VR) format. • DVD-RW shows in the display when a VR format DVD-RW disc is loading. DV-360-S...
Page 88
Rights Management) copy protection will not play and the message Can’t play this format will be displayed (NO PLAY in the front panel display). The Windows Media™ logo printed on the box indicates that this player can playback WMA data. DV-360-S...
Page 89
Audio encoded at 128Kbps should sound close to regular CD Audio quality. This player will play lower bit-rate files, but please note that the sound quality becomes noticeably worse at lower bit-rates. DV-360-S...
7.4 CLEANING Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DV-360-S...
• Press and hold for fast reverse/forward restart. scanning. • Press to jump to the previous/next chapter or track. Press to start or resume playback. This mark indicates compatibility with DVD-RW discs recorded on a DVD recorder in Video Recording mode. DV-360-S...
Page 92
Match the colors of supplied audio/video cable. the jacks and cables for correct stereo sound. S (S-video output) This is an S-video output that you can use instead of the video output described in 5 above. DV-360-S...
Page 93
Indicates that the character display is selected. showing a CD or Video CD track number. 11 DTS Lights when a DTS soundtrack is playing. Lights during multi-angle scenes on a DVD disc. Lights in any of the repeat play modes. DV-360-S...
Page 94
Press to pause playback; press again to restart. 12 PLAY MODE Press to display the Play Mode menu. (You can also get to the Play Mode menu by pressing HOME MENU and selecting Play Mode). DV-360-S...
Page 95
ENTER button in 6 above). 24 ZOOM 18 MENU Press to change the zoom level. Press to display a DVD disc menu, or the Disc Navigator if a VR format DVD-RW, CD, Video CD , MP3, WMA or JPEG disc is loaded. DV-360-S...